ngHobbies
50 AMP SENSOR FOR EPI STORM
Content of the package:, 1 x 50Amp current sensor, Datasheet:, Click here,
The EPI Storm requires a current sensor. Since different users ...ngHobbies
HITEC HTS-SS SENSOR STATION
,
The HItec compact sensor station collects data from each sensor ...ngHobbies
HITEC HTS-GPS GPS SENSOR
,
The Hitec HTS-GPS sensor displays constant directional information such as ...ngHobbies
MK 6MM PROPELLER MOUNT FOR 3538 MOTORS
,
MK propeller mount for APC type propellers, with 6mm shaft. ...ngHobbies
OKTO XL POWER DISTRIBUTION BOARD
| • Dimensions | 120 x 120 x 1 mm |
Specifications:, , Documentation:, -,
This is a power distribution board for the Okto XL. ...ngHobbies
QUADRO XL POWER DISTRIBUTION BOARD
| • Dimensions | 120 x 120 x 1 mm |
Specifications:, , Documentation:, -,
This is an 4-fold power distribution printed circuit board for ...ngHobbies
LIPO HOLDER
Assembly instructions:, Click Here,
This is the new LiPo holder from Mikrokopter. It will ...ngHobbies
APC 13X6.5 ELECTRIC PROPELLER
| - External diameter | 13" |
| - Pitch | 6.5" |
| - Mounting hole | approx 6.35mm |
| One propeller, manual and 5 centering rings for the following dimensions | 0.128"(3.25mm), 0.158"(4mm), 0.197"(5mm), 0.237"(6mm) , 0.313"(7.95mm). |
Technical Data:, Package contains:,
This is a 13 x 6.5 electric propeller (Not Slow ...ngHobbies
NAVI CONTROLLER V2.0
| Other components | Ribbon cable and connectors. |
The following items are included in this kit:, ,
This item is the Navi-Controller kit with an ARM9 microcontroller ...ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO NO SERVOS
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
EPP0845 CF PROPELLER PAIR
| - Pitch | 4.5" |
| - Mounting hole | 5mm |
Technical Data:, - External diameter: 8", Package contains:, One pair of counter rotating propellers (one of each direction - total 2),
This is a pair of left and right propellers be ...ngHobbies
WI 232 V2.0 MODULE PAIR
The following items are included in this kit:, 1 x Wi232 ground station module, Instructions:, Setup and instructions on wiki,
This set contains two ready assembled and preconfigured WI232 V2.0 ...