ngHobbies
GPS-SHIELD 1.1
The following items are included in this kit:, , Documentation:, Click here,
This cover is made from thin circuit board which will ...ngHobbies
BL-CTRL V1.2 SPEED CONTROLLER EXTRA SWITCH
The following items are included in this kit:,
This BL-Ctrl programmed for the Hexa nad Optokopter opertion. Each ...ngHobbies
APC 13X6.5 ELECTRIC PUSHER PROPELLER
| - External diameter | 13" |
| - Pitch | 6.5" |
| - Mounting hole | approx 6.35mm |
| One propeller, manual and 5 centering rings for the following dimensions | 0.128"(3.25mm), 0.158"(4mm), 0.197"(5mm), 0.237"(6mm) , 0.313"(7.95mm). |
Technical Data:, Package contains:,
This is a 13 x 6.5 electric pusher propeller (Not ...ngHobbies
3 CELL BALANCING ADAPTER
Package contains:, One balancing cable for 3 cell batteries.,
This is a balancer adapter for the 3 cell Vislero ...ngHobbies
SPEKTRUM SATELLITE DIVERSITY CONTROLLER
| Connector 1 | Connection to the flight controller |
| Connector 2-5 | Connection to satellite receivers |
Binding Instructions:, As any spektrum receiver, the diversity board and the satellite receivers connected to it will have to be bound to your spektrum transmitter. To enter the binding mode, you will need to hold the binding button pressed while powering on the circuit. All attached satellite recievers will be blinking fast during binding mode. The LED on the diversity receiver board will blink briefly 3-6 times, then it will turn off for a few seconds after which it will start flashing again - waiting for the RC signal. At this point follow the instructions of your RC transmitter to turn it on in binding mode. When the RC binding signal is detected, the satellite receivers will follow their routine of binding and blink slower. When the binding is complete, the LED's on the satellite recievers will stay on and on the diversity board will turn off., The package contains:, 1 x MK Diversity Controller, Documentation:, Additional documentation translated by google:, Click here,
This litte diversity controller has been designed to connect 4 ...ngHobbies
XBEE INTERFACE ADAPTER PAIR
| Industrial operating temperature range | -40 ° C to +85 ° C. |
Specifications of the USB module:, pre installed FTDI USB to serial converter chip, no driver is requored for most Windows systems., The following items are included in this kit:, 1 x USB Interface adaptor, Important:, xBee modules are NOT included in this kit., Manual:,
This interface pair has been developed by New Generation Hobbies ...ngHobbies
CUSTOM MK QUAD CENTERPLATE
,
This is a custom made centerplate for the MikroKopter's quad ...ngHobbies
ROBBE ROXXY BRUSHLESS OUTRUNNER 2815
| Power | 40W |
| Weight (with cable and adapter) | ca. 33 g |
| Efficiency | 79% |
Technical Data:,
The Roxxy brushless outrunners are more efficient high torque very ...ngHobbies
100 AMP SENSOR FOR EPI STORM
Content of the package:, 1 x 100Amp current sensor, Datasheet:, Click here,
The EPI Storm requires a current sensor. Since different users ...ngHobbies
MIKROKOPTER BASIKSET OKTO XL
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-OktoXL |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
ACC UPGRADE FOR FC 2.1
Please note:, the picture of this product on our website is Copyright Mikrokopter.de,
For the installation of this board very good soldering skills ...