ngHobbies
ROBBE ROXXY BRUSHLESS OUTRUNNER 2827-35
| Normal load | 6–9 A |
| Maximum Load (max 60 sec.) | 10 A |
| Idle Rotation | 760 prm |
| Reccomanded propellers | 10x4.5 (EPP1045), 12x4.5 (EPP1245) |
| Wellenleistung | ca. 110 W |
| Maximum thrust | ca. 820 g |
| Weight (with cable and adapter) | ca. 54-68 g |
| Dimension | 28,8 x 29 mm |
| Bore diameter | 3,17 mm |
Technical Data:, Lithium cell number: 4,
The Roxxy brushless outrunners are more efficient 14 pole high ...ngHobbies
MIKROKOPTER BASIKSET L4-ME
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included in this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Quadro?action=show&redirect=en%2Fassembly |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, 1 x preassembled FlightCtrl ME V2.1 with Altitude Sensor, Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
BLACK ALU RIGGER FOR 400MM MK FRAME
,
This is the Red aluminum rigger only, for the 400mm ...ngHobbies
MIKROKOPTER BRUSHLESS OUTRUNNER MK3638
| •Lithium cell count | 3-6 |
| •Load current | max. 20A |
| •Maximum load current. (60 sec) | 25 A |
| •No-load speed | 770 rpm / V |
| •Recommended Propeller Size | 10" .. 14" |
| •Machanical power | 350 W |
| •Thrust max. | 2200 g |
| •Wire length | about 52 cm |
| •Total weight (without cable) | approx 100g |
| •Dimensions | h=35mm, d=38mm |
| •Shaft diameter | 4 mm |
Technical Data:,
This is a 14 pole brushless outrunner motor with high ...ngHobbies
FLEXIBLE BLUE LED STRIP
| - Length | 10cm (6 x LED) |
| - Voltage required | 12V |
| - Mounting | remove the protective layer from the bottom to stick it to your MK. |
Technical Data:, Package contains:, One strip of 10cm long felxible blue LED strip with 6 LED's on it.,
This is a felxible high output blue LED strip. Usually ...ngHobbies
MIKROKOPTER BASIKSET HEXA 2
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Hexa |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...ngHobbies
BL-CTRL V1.2 SPEED CONTROLLER
The following items are included in this kit:,
The BL-Ctrl is the speed controller of choice for any ...ngHobbies
BLACK ALU RIGGER FOR MK OKTO XL
,
This is the black long aluminum rigger only, for the ...ngHobbies
EPP1045 CF PROPELLER PAIR
| - External diameter | 10" |
| - Pitch | 4.5" |
| - Mounting hole | 5mm with inserts for 3mm and 4mm shafts. |
Technical Data:, Package contains:, One pair of counter rotating propellers (one of each direction - total 2),
This is a pair of left and right propellers to ...ngHobbies
AT MEGA 644P-20AU
| Clock | max. 20 MHz. |
ngHobbies
BLACK ALU RIGGER FOR 500MM MK FRAME
,
This is the black aluminum rigger only, for the 500mm ...