ReadyMadeRC
MINI METAL HEAD - G10 ARMS
Features & Specifications:, , Recommended Motors:,
Metal-H Mini FPV Quadcopter Frame One of the Strongest in ...ReadyMadeRC
AIMDROIX ALUMINUM EXTENDED ARM FOR DJI MULTIROTORS V1.0 (BLUE)
| Note | This listing is for a single arm ONLY |
| Motor mounting holes | 16mm to 25mm |
| Weight | 72 grams. (DJI Stock arms 54g) |
| http | //www.readymaderc.com/store/index.php?main_page=product_info& |
Features:, , : Users should verify that the motor mount screws don't go in too far into their motor since these arms are thinner than the stock arms!!!, : For larger diameter motors, when using the legs, you simply need to use these spacers:,
Please do not back order this item. V1.0 - These ...ReadyMadeRC
HS-7955TG HIGH TORQUE, TITANIUM GEAR, CORELESS ULTRA PREMIUM
| Motor Type | Coreless |
| Bearing Type | Dual Ball Bearing |
| Speed (4.8V/6.0V) | 0.19 / 0.15 |
| Torque oz./in. (4.8V/6.0V) | 250 / 333 |
| Torque kg./cm. (4.8V/6.0V) | 18.0 / 24.0 |
| Size in Inches | 1.57 x 0.78 x 1.45 |
| Weight ounces | 2.29 |
| Weight grams | 64.92 |
Size in Millimeters:, 39.88 x 19.81 x 36.83,
Product Description Hitec's best servo just got better. Based on ...ReadyMadeRC
FLYTRON - SLED IR SHUTTER CONTROL - SONY
| You can also attach it to IR window of your camera with a sticky tape. Weight | 4gr |
| Voltage | 3-7 volts |
| Current | 2mA |
| Cable Length | 30cm |
| Accepting Signal | 1-2ms PPM over servo line. |
| UP Position | Photo |
| position | Idle mode of |
| DOWN Position | Video Start/Stop |
| Note 2 | You should enable " |
Operation:, Just plug it to your, Control Modes:, Compatible Models:, , Note 1:, Your model may not be included in the above list. Please check the manual of you camera to see whether it is compatible with IR video start/stop option.,
The sLED is a unique, lightweight and robust Infrared RC ...ReadyMadeRC
RMRC ANACONDA - KIT
| Wingspan | 2,060mm |
| Wing Area | Approx. |
| Length | 1,410mm |
| Motor | 35-48 800-1000kv Brusless outrunner |
| Propeller | 13x6.5 E or 14x5.5 E (Not included) |
| ESC | 60-80A ESC with switch mode BEC |
| Servos | 3x 30g and 2x 17g Metal Gear Digital |
| Flap servos | HS-81 |
| Battery | Li-Po 4s 5,000mAH - 20,000mAH (Additional nose weight needed with smaller batteries) |
| Center of Gravity | 1/3 of wing from leading edge at the main spar |
| Approximate flight duration | 45 minutes to over an hour depending on configuration |
| Fuselage dimensions (Inside) | L 66cm (26.5") x W 15cm (6") x H 8cm (3") |
| RcGroups.com Unboxing Video with Jim Graham | (PNP version shown) |
Features:, , Specifications:, , Control:, Width, Looking inside the fuselage:, , Notes:,
Anaconda KIT After months of testing, we are proud to ...ReadyMadeRC
RMRC LUNAR ECLIPSE - KIT
| Wingspan | 1240MM |
| Length | 960MM |
| Wing Area | 21dm sq (Mainwing Area) |
| Motor | Brushless outrunner motor 2820-3540, 900-1000kv |
| Prop | 10x7E |
| ESC | 20-30A |
| Servos | 9g (Hitec HS-65's work perfectly!) |
| Battery | Li-Po 3s 2200mAH - 3300mAH |
| Center of Gravity | 70-80mm from leading edge of wing root |
| CG Location | (Red line) |
Features:, , Specifications:, , Inside the fuselage and motor bay:, , Control rods, servos, and back of fuselage:, , Tail:, , Hardware and air exit:, , : :),
Introducing the RMRC Lunar Eclipse! This semi-scale aircraft offers excellent ...ReadyMadeRC
MARCO POLO - TRACKER SET
From Tim Crabtree at Eureka Products regarding possible interference:, Regarding interoperability with your existing control and video telemetry systems, our tag transceiver (the part the goes in the model) does not transmit any RF energy until commanded to by the handheld locator. In fact, each and every transmission it makes is only in response to receiving a command from the locator. The user is in total control of that from the ground so interference during flight is not an issue., Includes:,
Quickly and easily track, locate and recover wayward RC models ...ReadyMadeRC
DJI ZENMUSE H3-3D STANDARD
| Static current | 400mA (@12V) |
| Dynamic current | 600mA (@12V) |
| Gimbal Input Power | 3S~6S (12V ~ 26V) |
| Operating Temperature | -10°C ~ 50°C |
| Gimbal Dimensions (With Damping Unit) | 97mm X 95mm X 73mm |
| GCU Weight | 22g |
| Tilt/Roll | ±0.02°? |
| Yaw | ±0.03° |
| Maximum Controlled Rotation Speed | Tilt axis |
Supported Camera:, GoPro3, GoPro3+ Black and Silver, GCU Input Power:, 3S~6S LiPo (12V~26V), Assistant Software System Requirement:, Windows XP SP3; Windows 7; Windows 8, Gimbal Weight:, 168g (camera excluded), GCU Dimensions:, 42 mm X 32 mm X 9.3 mm, : Tilt axis control: ?130 ~ +45°,
Zenmuse H3-3D Features 3-axis high performance gimbal Effortless Setup Compatible ...ReadyMadeRC
UMX RADIAN BNF
| Wingspan | 28.7 in (730mm) |
| Overall Length | 16.5 in (418mm) |
| Flying Weight | 1.50 oz (43 g) |
| Motor Size | 8.5mm coreless brushed motor |
| Radio | 4+ channel transmitter required |
| CG (center of gravity) | 1.22 in (31mm) back from the leading edge of wing at wing root |
| Recommended Battery | 1S 3.7V 150mAh 25C LiPo |
| Approx. Flying Duration | 8-10 minutes |
| Charger | 1S 300mA LiPo USB Charger |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Indoor/Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |
® technology gives a pilot the feeling of flying a much larger glider especially outdoors because of its renowned ability to smooth out the effects of wind and turbulence. Its distinctively curved wing delivers outstanding lift and impressive glide ratio using 3-channel control simplicity. The lightweight brushed power system requires just a single-cell Li-Po battery to provide excellent launch performance and long flight times. Plus the one-piece wing can be easily removed and stored in the handle-equipped box making your ability to soar through the clouds as convenient as can be. You’ll be in the air in no time thanks to great features like:, , Flaps: No,
The first ultra micro motor glider with AS3X® technology. Features ...ReadyMadeRC
CARBON-Z CUB BNF BASIC
| Wingspan | 84.6 in (215 cm) |
| Overall Length | 55.8 in (142 cm) |
| Wing Area | 1100 sq. in. (71.0 sq. dm.) |
| Flying Weight | 8.15 lb (3.70 kg) |
| Motor Size | 50-size brushless outrunner (installed) |
| Radio | 6+ channel DSM2/DSMX transmitter (required) |
| Servos | (4) 26-gram MG mini servos, (2) 13-gram micro servos (installed) |
| CG (center of gravity) | 4.72 in (120mm) back from leading edge of wing |
| Wing Loading | 17 oz/sq ft |
| Prop Size | 15 x 5.5 Electric (included) |
| Speed Control | 60-amp brushless (installed) |
| Recommended Battery | 22.2V 6S 3200mAh LiPo (required) |
| Flaps | Yes |
| Approx. Flying Duration | 7 minutes |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |
| Spinner Size | 2.64 in (67mm) |
Optional Accessories:, - Float set (EFL1045016), Retracts: No,
Features Easy-to-complete final assembly Quique Somenzini design and attention to ...ReadyMadeRC
RADIAN PRO PNP
| 5-channel control | aileron, elevator, flaps, rudder and throttle |
| Wingspan | 78.5in (2000mm) |
| Overall Length | 45.0 in (1140mm) |
| Flying Weight | 34.6oz (980g) |
| Motor Size | 480 Outrunner Brushless Motor, 960Kv |
| CG (center of gravity) | 2.75 in (70mm) back from leading edge of the wing at the root |
| Prop Size | 9.75 x 7.5 Folding Prop |
| Speed Control | E-Flite 30Amp Pro Switch-Mode Brushless ESC |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |
ReadyMadeRC
SPORT CUB PNP
| Wingspan | 51.0 in (1300mm) |
| Overall Length | 34.0 in (865mm) |
| Flying Weight | 33.3 oz (945 g) |
| Motor Size | 480 Brushless Motor 960Kv |
| Radio | 4+ channel (5+ channel for optional flaps) (required) |
| Prop Size | 9 x 6 |
| Speed Control | 18 amp brushless ESC (installed) |
| Recommended Battery | 11.1V 3S 1300mAH LiPo battery (required) |
| Flaps | Optional |
| Landing Gear | Yes |
| Steering | Yes |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
| Assembly Time | Less than 1 Hour |
| Is Assembly Required | Yes |
ReadyMadeRC
AIMDROIX EVO ONE - Y6
| - Frame size | 610mm (with extended length arms) |
| -Max props size | 16in on top motor / 15in props on lower motor. |
Frame configurations:, The frame was designed to be as customizable as possible so that it could be built in many different multirotor configurations. The default frame configuration is a Y6 but it can be built as a quad, quad X8, Y4, V- tail quad and tricopter. This is possible by just installing the optional configuration kits sold separately., Main Frame and landing gear:, The top and bottom plate are stiffened with an innovative aluminum beam stiffeners, which increase the stiffness of the frame plates without the need of standoffs or sandwiched plates. This maximizes the space between the top and bottom plates for a better placement of the ESC and batteries. The integrated landing gear increases the stiffness of the bottom plate and allows two high capacity batteries to be mounted on the sides of the frame. The height of the landing gear can be easily changed by replacing the 8mm carbon fiber leg tubes., Camera mounting system:, The innovative camera mounting system was designed to provide vibration isolation for the camera and video transmitter electronics. The camera plate is mounted on 6 AIMDROIX soft dampers that the takes away the vibrations from the props and motors. The rear support dampening balls are mounted on the top plate brackets so that they are in compression load. This allowed mounting the camera gimbal and FPV camera on front of the plate, away from the top and bottom props view and maintain the plate parallel with respect to the frame plates. The plate was designed to fit the Feiyu Tech FY-G3 brushless gimbal without modifications., Designed for the Aimdroix Aluminum Arms:, The frame was designed to fit the AIMDROIX aluminum arms that have been well proven for many customers around the world. With the optional AIMDROIX arms accessories, it possible to build the most versatile multirotor frame in the market., Key Features:, -Innovative vibration isolated camera system., Y6 Specs:, -Aprox frame,
Aimdroix EVO ONE Y6 The AIMDROIX EVO ONE is the ...ReadyMadeRC
C-RAY 180 PNP
| Wingspan | 21.7 in (550mm) |
| Overall Length | 13.5 in (342mm) |
| Wing Area | 126 sq. in. (8.05 sq. dm.) |
| Flying Weight | 4.40 oz (125 g) |
| Motor Size | 180-size, 2500Kv brushless outrunner (installed) |
| Radio | 4+ channel transmitter with elevon mixing |
| Servos | (2) 3-gram super sub-micro servos (installed) |
| CG (center of gravity) | 3/4 in (18mm) in front of the forward edge of the servo casing |
| Prop Size | 4.5 x 4 electric propeller (installed) |
| Speed Control | 3-amp brushless (installed) |
| Recommended Battery | 7.4V 2S 430–450mAh LiPo battery (required) |
| Control Throw (Ailerons) | Low |
| Control Throw (Elevator) | Low |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Outdoor |
Is Assembly Required: No,
Features Fully assembled and hinged with control horns and pushrods ...ReadyMadeRC
UMX BEAST 3D BNF BASIC
| Wingspan | 14.7 in (374mm) |
| Overall Length | 15.7 in (400mm) |
| Wing Area | 83.8 sq in (54.2 sq dm) |
| Flying Weight | 2.54 oz (72 g) |
| Motor Size | BL180 2500Kv brushless outrunner |
| Radio | 4-channel minimum |
| Trim Scheme Colors | Black, Red, Silver |
| CG (center of gravity) | 19mm back from leading edge of bottom wing |
| Wing Loading | 3.4 oz/sq ft (1.01 g/sq dm) |
| Prop Size | 5 x 2.75 inch |
| Recommended Battery | 2S 7.4V 180mAh Li-Po |
| Control Throw (Ailerons) | Low |
| Control Throw (Elevator) | Low |
| Control Throw (Rudder) | Low |
| Approx. Flying Duration | 5 minutes |
| Minimum Age Recommendation | 14 years |
| Experience Level | Intermediate |
| Recommended Environment | Indoor/Outdoor |
Is Assembly Required: No,
Seize the UMX™ Beast® 3D, Equipped with AS3X® Technology, and ...