HiModel
LIBRA-METER 100A WATT-METER/BATTERY CHECKER/SELF-BALANCER
| ●Input power | Max 60V (both on watt-meter and battery checker) |
| ●Max. current | 100A (watt-meter) |
| ●Min operating voltage | 6.6V |
| ●Current consumption | 20mA at battery checker program |
| ● Dimension | 105 x 53 x 20 mm |
| ● Weight | 120g |
, , , , , , Specifications:, , , , , , , , , , , G.T.Power Rc Libra-Meter 100A watt-meter/battery checker/self-balancer, , ,
Features: Libra-Meter is a very sophisticated electronic device that controlled ...2 Reviews
HiModel
6S BALANCE CONNECTOR TO 2X 3S CONVERSION CABLE (HIMODEL/ALIGN TYPE CONNECTOR)
| Length | 6.5cm (including connectors) |
, , , , , , Specifications:, , , , , , , , , , , 6S (female) to 2x 3S (male) conversion cable, Compatible with all HiModel Series Li-poly batteries., Compatible with most of chargers from E-sky, RC-Power, Maxpro, Smart plus, Dynam and HiModel etc., , ,
Includes/Requires: INCLUDES: 1 x conversion cableHiModel
4S BALANCE CONNECTOR TO 2X 2S CONVERSION CABLE (HIMODEL/ALIGN TYPE CONNECTOR)
| Length | 6.5cm (including connectors) |
, , , , , , Specifications:, , , , , , , , , , , 4S (female) to 2x 2S (male) conversion cable, Compatible with all HiModel Series Li-poly batteries., Compatible with most of chargers from E-sky, RC-Power, Maxpro, Smart plus, Dynam and HiModel etc., , ,
Includes/Requires: INCLUDES: 1 x conversion cableHiModel
3.5-7V RX BATTERY VOLTAGE LEVEL LED INDICATOR
| Wire length | 28cm |
| Working voltage | 3.5 to 7V (typically for 4.8V or 6V RX battery) |
| Connector type | Futaba/JR compatible |
| 5V above | green LED |
| 5-4.5V | Green , flash slowly |
| 4.5-4V | Red LED |
| Below 4V | Red LED, quick flash |
, , , , , , Specifications:, , , , , , , , , , , 3.5-7V RX Battery Voltage Level Indicator, Weight: 4g, Working current: , Status:, * This unit can only work under 7V, and can not connect directly to 2S Lipo., , ,
HiModel
LOW VOLTAGE BUZZER FOR 2S/3S/4S LIPO BATTERY
| When testing full power (>3.6V) 2S Lipo battery | 2 green LED keeping light. |
| When testing full power (>3.6V) 3S Lipo battery | 3 green LED keeping light. |
| When testing full power (>3.6V) 4S Lipo battery | 4 green LED keeping light. |
| Weight | 6.5g / 0.23oz |
| Size | 34 x 25 x 11mm |
, , , , , , Specifications:, , , , , , , , , , , Low voltage buzzer for Lipo battery, When voltage, , ,
2 Reviews
HiModel
FPV 2.4G/5.8G WIRELESS ALL-IN-ONE HEAD TRACING GOGGLE/VIDEO GLASSES
, , , , , , Specifications:, , , , , , , , , , , Compatible transmitters (the transmitter for RC model, not the video transmitter):, FUTABA FF-7, FF-8, FF-9, T9Z, T12MZ and T14MZ., * Other types transmitter may not supported., * there are two different colors, black and silver, we will send in random based on stock availability., , ,
Features: We stuff everything for FPV into this tiny goggle ...3 Reviews
HiModel
EXTREME BRUSHLESS MOTOR CHECKER BMC-01
| Input Voltage | 7.4-8.6V (Suggested to use a 7.4V 2S1P LiPo Battery) |
| LCD Display Screen | Blue Backlight background, white text, 16 characters x 2 lines |
| Dimension | 136.5mm x 80.6mm x 47mm |
| Net Weight | 290g |
| Supported Motor | Sensor or Sensor-less Brushless motor. |
| (a) Standard 540 size RC car motor | 2.5 turn or over, 2 Poles(In-runner motor) |
| (b) Flight Motor | support sensor-less brushless motor, 6 poles(Out-runner motor) |
, , , , , , Specifications:, , , , , , , , , , , Current Drawn less than 18A at 8.4V without loading., , ,
Features: 1. Brushless Motor Checking KV Measurement RPM Measurement Ampere ...HiModel
EMAX 11.1V & 7.4V LITHIUM BATTERY FIELD CHARGER
| 1. Power Input | 11-14V DC |
| 2. Load capacity | 2-3 cell Li-ion/ Li-poly battery (7.4V-11.1V) |
| 3. Cut-off Method | Autodetect and Cut-off |
| 4. Output current | 800mA |
| 5. Size | 75 x 50 x 25 mm |
| 6. Weight | 46.7g / 1.65oz |
| Charging connector type | compatible with all HiModel/Align batteries. |
| * Red light | power indication |
| * Charging | Green light on |
| * Charging finish | Green light off |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: The E-sky EC103A charger can directly charge 2-3 cell ...1 Reviews
HiModel
FRONT TIRE & WHEEL RIM(F) 06010 FOR 94107 & 94105-6
| Manufacturer Code | 06010 |
| Width | 31mm |
| Diameter | 85mm |
| Wheel Nut | 12mm |
| Wheel Diameter | 62mm |
, , , , , , Specifications:, , , , , , , , , , , Front Tire & Wheel Rim(R) 06026 for 94107 & 94105-6 (Electric version), * The color of the rims may different from the picture, there are green and yellow two colors, will send in random according to stock availability., , ,
Includes/Requires: 2 x Tires & Wheel Rims(F)HiModel
REAR TIRE & WHEEL RIM(R) 06026 FOR 94107 & 94105-6
| Manufacturer Code | 06026 |
| Width | 40mm |
| Diameter | 85mm |
| Wheel Nut | 12mm |
| Wheel Diameter | 62mm |
, , , , , , Specifications:, , , , , , , , , , , Rear Tire & Wheel Rim(R) 06026 for 94107 & 94105-6, * The color of the rims may different from the picture, there are green and yellow two colors, will send in random according to stock availability., , ,
Includes/Requires: 2 x Tires & Wheel Rims(R)HiModel
FRSKY 2.4G 6-CHANNEL TWO WAY COMMUNICATION RECEIVER D6FR
| Compatible with FrSky two way telemetry modules | DFT, DJT, DHT, DHT-U |
| Dimension | 42*22*11mm |
| Weight | 7.1g |
| Operating Voltage Range | 4.0V-10.0V |
| Operating Current | 50mA |
| Specified Range | 1.5km |
| Resolution | 3072 (>11bit) |
| Frame Rate | 18ms (FS) |
| Please kindly follow the steps below to perform range check | (Note |
, , , , , , Specifications:, , , , , , , , , , , 1.1 Compatibility:, 1.2 Specification:, 9ms (HS), Setup, 2.1 Bind procedure:, 1) Turn your transmitter on and switch it to PPM mode (if not set). Turn your transmitter off., 2)Turn your transmitter on while holding the F/S button on the transmitter module (Please make sure that both switches on the transmitter module are OFF in two way mode) Release it in a few seconds. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind to the receiver., 3) Connect battery to the receiver while holding the F/S button on the receiver. The LED on the receiver will flash, indicating the binding process is completed., 4) Turn on the transmitter and connect battery to the receiver. The Green LED on the receiver will indicate the receiver is receiving commands from the transmitter., 2.2 Range check:, It is highly suggested to perform pre-flight range check. Caution must be paid when you perform range check in environment with metal fences, concrete buildings, or rows of trees. Loss of signal may be experienced from reflections., 1) Place the model at least two feet (60cm) above non-metal contaminated ground (like wooden bench)., 2) Place the receiver’s antennas apart. Do not let the antennas touch the ground., 3) Place the antenna of the transmitter in a vertical position., 4) Turn on the transmitter and receiver, press the F/S button of the transmitter for 4 seconds to enter range check mode, the RED LED of the transmitter module will be off, GREEN LED will flash rapidly, the BEEPER will sound. The effective distance will be decreased to 1/30 of full range., 5) Walk away from the model whi,
Features: Features: 1) Lighter in weight and smaller in dimension. ...HiModel
FRSKY RECEIVER UPGRADE LITE
| Refer to http | //www.frsky-rc.com/download.asp?id=22. for instructions and software etc. |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: FrSky receiver upgrade lite Includes/Requires: Includes: 1 x receiver ...HiModel
FRSKY 2.4G 8-CHANNEL RECEIVER W/PPM OUTPUT V8R7SP
| Model | V8R7-SP |
| Operating Voltage Range | 3.0V-16.0V |
| Operating Current | 30mA |
| Resolution | 3072 |
| Latency | 22ms |
| Specified | 7CH, 9g, 49mm×23mm×12mm, 1.5km-2.5km |
| Warning | DO NOT connect servos to channel 8, otherwise servos will get hot or even burn out. |
, , , , , , Specifications:, , , , , , , , , , , V8R7-SP improves the smoothness of high-speed digital servos., Bind Procedure:, 1) Turn on your transmitter and switch it to PPM mode, turn off the TX., 2) Turn on your transmitter while holding the programming button. Release it a few seconds later. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver., 3) Connect the battery to the receiver while holding the receiver’s F/S button. The LED on the receiver will flash, indicating the binding process is complete. Turn off the transmitter and receiver., 4) Turn on your transmitter. Connect the battery to the receiver when ORANGE LED on TX is on. The LED on the receiver will indicate the receiver is receiving commands from the transmitter. In a few seconds system is ready to work (communication is established)., Binding is required only to set up a new link (like new or additional receiver or transmitter module). To control multi-receivers, every receiver should be programmed with the transmitter in binding state., Failsafe:, V8R7-SP supports failsafe function for all channels. Just do it as bellow:, After the receiver has been bind, press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, the failsafe is set up successfully., If you do not need the failsafe function any more, just re-bind the receiver., , ,
Includes/Requires: Includes:1 x V8R7SP receiverHiModel
GWS ON-BOARD INDICATOR GW/OBI001
| Voltage Selection | 1 ~ 4 Cells Li-PO |
| Size | 43x11mm /1.69x0.43 in |
| Weight | 5 gram / 0.18 oz |
, , , , , , Specifications:, , , , , , , , , , , Light Weight & Compact, Easy to Carry & Use, Green/Yellow/Red LED Indicator, Easy to Install on Board, CE & RoHS Ready, , ,
1 Reviews
HiModel
HIMODEL (APLUS, ALIGN) 6-PIN/5S FEMALE TO THUNDER POWER MALE ADAPTOR CABLE
| Length | 15cm (including connectors) |
, , , , , , Specifications:, , , , , , , , , , , HiModel (Aplus, Align) 6-pin/5S Female to Thunder Power Male Adaptor Cable, Compatible with most of chargers from E-sky, RC-Power, Maxpro, Smart plus, Dynam and HiModel etc., , ,
Features: HiModel (Aplus, Align) 5S Female to Thunder Power Male ...