Flying-Hobby
ROTOR TECH 610MM 3D FLYBARLESS CARBON MAIN BLADES
| Length | 610mm |
| Width | 57mm |
| Weight | 163-168g |
| Grip | >=12mm |
| Hole | 4mm |
| Airfoil | Symmetrical |
| Tip | Aeroflat |
| Make | Carbon Fiber |
| Common Application | 46-50 Size RC Helicopters |
Specifications:, ,
Flying-Hobby
ROTORTECH 560MM 3D CF BLADES (YELLOW TIP)
| Length | 560mm |
| Width | 53mm |
| Grip | >12mm |
| Hole | 3-4mm |
| Airfoil | Symmetrical |
| Tip | Aeroflat |
| Make | Carbon Fiber |
| Common Application | 30 Size RC Helicopters. Designed for hard 3D competition. |
Specifications:, Includes:, 1x 3D/holographic decal sheet, RotorTech™ Standard Features:, Safety wire runs alone the inner core of the blade. This keeps the blades in one piece upon a crash to insure safety to pilots and bystanders.,
These 560mm carbon fiber main rotor blades are designed for ...Flying-Hobby
CAPACITOR PACK (12S MAX, 50.0V, 1100UF)
Helis:, CC CapPack is highly recommended for all 500 class and larger heli applications where Y harnesses and long wires can bleed voltage and hard collective pulls can strain even the most powerful batteries., Cars/Trucks:, With their high torque requirements – going from 0 to 100% throttle isn't easy on controllers or batteries - RC cars and trucks put enormous loads on brushless power systems. Use CC CapPack to help your system power through the abuse., Aircraft:, Larger electric power systems lead to larger electric powered aircraft, and sometimes the distance between the battery pack and the ESC grows beyond the length of the wires installed on the components. Adding wire also adds inductance, which can increase the ripple voltage in a system. CC CapPack essentially negates the ripple caused by the addition of up to 8 inches of length to the battery wires., Note: All Castle controllers with data logging capabilities can report the ripple voltage they encounter during use. Ripple voltage peaks should always be less than 10% of the total pack voltage; the smaller the ripple voltage the better. If an application exhibits more than 10% ripple voltage under peak loads, the user should consider using higher discharge (C Rating) batteries, shorter wires, higher current connectors, better gearing or a smaller load.,
CC CapPack is useful in all brushless motor applications, where ...Flying-Hobby
BALANCE CHARGER RCC-3SX
| 4.Auto-detected charge status display. (Red light | while charging Green light |
| ● Input Voltage | AC 100V~240V(50/60Hz) |
| ● Output Voltage | 2cell DC 7.4V / 3cell DC 11.1V |
| ● Supported Battery Type | Li-polymer / Li-ion |
| ● Charging Method | CC/CV |
| ● Size | 123x74.3x32mm |
| ● Weight | 260g |
| Accessories | ●AC Power cord x1 |
Instructions:, 1.Suitable for international AC 100V~240V., NOTE:, 1.Do not leave the charger is operating unattended as it may cause a fire., Specification:, ● Charging Current: 2A,
2.Voltage balancing charging suitable for 2S 7.4V and 3S 11.1V ...Flying-Hobby
HIGH QUALITY CARBON FIBER MAIN BLADES (810MM) RED
| Product Detail | • Length |
| • Width | 65mm |
| • Weight | 410-420g |
| • Grip | 14mm |
| • Hole | 5mm |
| • Airfoil | Asymmetric |
| • Tip | 4 dergee cathedral Angled |
| • Make | Carbon Fiber |
| • Common Application | Large Gas Powered RC Helicopters |
Flying-Hobby
ROTORTECH 640MM CARBON FIBER SYMMETRICAL MAIN BLADES
| Length | 640mm |
| Width | 59mm |
| Weight | 135-140g |
| Grip | >12mm |
| Hole | 4-5mm |
| Airfoil | Symmetrical |
| Tip | Aeroflat |
| Make | Carbon Fiber |
| Common Application | 50 size RC Helicopters |
Specifications:, , Includes:, , RotorTech™ Standard Features:,
1x 3D/holographic decal sheet 4x 1mm thick washers 4x 2mm ...Flying-Hobby
ROTORTECH 550MM CARBON BLADES MAIN BLADE
| Length | 550mm |
| Width | 51mm |
| Grip Thickness | 12mm |
| Hole | 3-4mm |
| Airfoil | Symmetrical |
| Tip | Angled |
| Make | Carbon Fiber |
| Common Application | 30 size RC Helicopters |
Specifications:, Includes:, 1x 3D/holographic decal sheet, RotorTech™ Standard Features:, Safety wire runs alone the inner core of the blade. This keeps the blades in one piece upon a crash to insure safety to pilots and bystanders.,
2x spacers Low parasitic drag coeficient due to the efficient ...Flying-Hobby
DUAL-SHOULDER TRANSMITTER NECK STRAP
Features:, Two fixed points mode for transmitter tray, one fixed point mode for normal RC transmitter.,
Light weight, (dual-straps) only 208g; small, folded less than 30cm; ...Flying-Hobby
EDGE 95 MM SE PREMIUM CF TAIL ROTOR BLADES
| Specs | - Length |
| - Width | 29-25mm |
| - Root | 5mm |
| - Bolt Hole | 3mm |
Features:, - Airfoil designed specifically for high speed tail rotor application., Includes:, - One pair of EDGE blades.,
Product description EDGE high performance CF blades are new premium ...Flying-Hobby
KDE DIRECT ALIGN TREX 500 SERIES BOTTOM BRACKET UPGRADE
Features:, This upgrade is a direct replacement for the stock part, with no modification required to the frame or landing gear., Includes:, One (1) TREX 500E Aluminum Bottom Bracket Upgrade, Weight:, 42 g (design is FEA optimized for maximum strength and minimum weight),
Precision, CNC machined and clear anodized Aluminum 6061-T6 bottom bracket ...Flying-Hobby
APLUS 1000MAH-20C 4S1P
| Suggest For | SJM180 . |
| *Standard Discharge Rate | 20C(20A) |
| *MAX Discharge Rate | 25C(25A) |
| *Size | 70 x 35 x 22 mm |
| *Weight | 105g (With Wire) |
Guarantee:, ,
* APLUS batteries are guaranteed by manufacture during first 3 ...Flying-Hobby
APLUS 850MAH-15C 4S1P
| *Standard Discharge Rate | 15C(12.75A) |
| *MAX Discharge Rate | 18C(15A) |
| *Size | 53 x 30 x 29.5 mm |
| *Weight | 88g (With Wire) |
Guarantee:, ,
* APLUS batteries are guaranteed by manufacture during first 3 ...Flying-Hobby
EDGE 813MM PREMIUM CF BLADES
| Specs | - Length |
| - Root | 14mm |
| - Bolt Hole | 5mm |
Features:, - Airfoil designed for both Flybar and Flybarless helicopters., Includes:, - One pair of EDGE blades.,
EDGE high performance CF rotor blades are new premium blades ...Flying-Hobby
EDGE 325MM PREMIUM CF BLADES - FLYBAR VERSION
| Specs | - Length |
| - Width | 32mm |
| - Root | 4.5mm |
| - Bolt Hole | 3mm |
Features:, - Airfoil designed specifically for traditional flybar helicopters., Includes:, - One pair of EDGE blades.,
EDGE high performance CF rotor blades are new premium blades ...Flying-Hobby
EDGE 325MM PREMIUM CF BLADES - FLYBARLESS VERSION
| Specs | - Length |
| - Width | 32mm |
| - Root | 4.5mm |
| - Bolt Hole | 3mm |
| - Weight | ~ 24 grams |
Features:, - Airfoil designed specifically for flybarless helicopters., Includes:, - One pair of EDGE blades.,
EDGE high performance CF rotor blades are new premium blades ...