ngHobbies
AEROSIM RC TRAINING SIMULATOR
Features:, - Very realistic flight characteristics. The flight performance and physics of the models is very realistic - this usually is found only at a much higher priced simulators., See it in action here:, AeroSIM RC - Simulador Aeromodelismo Radio Control Flight Simulator, Download the trial version:, Click here,
The AeroSIM RC is the first simulator which was developed ...ngHobbies
FLEXIBLE GREEN LED STRIP
| - Length | 10cm (6 x LED) |
| - Voltage required | 12V |
| - Mounting | remove the protective layer from the bottom to stick it to your MK. |
Technical Data:, Package contains:, One strip of 10cm long felxible green LED strip with 6 LED's on it.,
This is a felxible high output green LED strip. Usually ...ngHobbies
CONNECTOR CABLE SET IMMERSION RC
Audio/Video Pigtail:, Black - Ground -, Power Connector Pigtail:, Black - Ground -,
This is a replacement cable set for the Immerion RC ...ngHobbies
TWINSTAR II ARF ELECTRIC RC PARKFLYER
Assembly goes quickly even for the novice. Most of the foam parts are interlocking and the servo locations are molded in for quick, accurate assembly. Two 6V Speed 400 motors with wiring harness and push on props are included in the airplane kit. Airplane is capable of simple aerobatics; loops and rolls are easily done. Good illustrated instructions. For 4 channels: Ailerons (2 servos), Elevator, Rudder and Throttle.,
56" wingspan, 42-3/4" long, 667 sq. in. wing area, 45 ...ngHobbies
FUNJET ULTRA ARF ELECTRIC RC AIRPLANE
,
Just when you thought your Multiplex FunJet was one of ...ngHobbies
EASYGLIDER PRO ARF ELECTRIC RC SAILPLANE
,
71" wingspan, 44" long, 645 sq. in. wing area, 32 ...ngHobbies
MULTIPLEX CULARIS ELECTRIC RC SAILPLANE
,
The Multiplex EasyGlider was the first step for many modelers ...ngHobbies
4 CHANNEL VIDEO SWITCH
| http | //www.vimeo.com/4449555 |
- Additional safety feature: In case the RC signal is lost, the device will switch back to Input 1 after about 2.5 seconds. The rationale behind this is the following: In case you have a forward and a backward facing camera, and you loose RC control while looking backwards, the device will switch back to the forward facing camera (assuming that this is connected to Input A) in order to allow you to look forward and resume flying the plane with forward view once you regain control. This feature is always useful to notify you that you are dangerously close to loose RC control of your plane., Demo Video :, Manual:, Setup and Utilization Manual,
The 4 Channel Video switch will allow you to switch ...ngHobbies
12/5VOLT 2 CHANNEL MINI VIDEO SWITCH
| http | //www.vimeo.com/1049216 |
- Additional safety feature: In case the RC signal is lost, the device will switch back to Input 1 after about 2 seconds. The rationale behind this is the following: In case you have a forward and a backward facing camera, and you loose RC control while looking backwards, the device will switch back to the forward facing camera (assuming that this is connected to Input A) in order to allow you to look forward and resume flying the plane with forward view once you regain control. This feature is always useful to notify you that you are dangerously close to loose RC control of your plane., Demo Videos:, FPV Piloting with 2 Cams 1 Downlink, Manual:, Setup and Utilization Manual,
The universal version of the 2 Channel Video switch will ...ngHobbies
SPEKTRUM SATELLITE DIVERSITY CONTROLLER
| Connector 1 | Connection to the flight controller |
| Connector 2-5 | Connection to satellite receivers |
Binding Instructions:, As any spektrum receiver, the diversity board and the satellite receivers connected to it will have to be bound to your spektrum transmitter. To enter the binding mode, you will need to hold the binding button pressed while powering on the circuit. All attached satellite recievers will be blinking fast during binding mode. The LED on the diversity receiver board will blink briefly 3-6 times, then it will turn off for a few seconds after which it will start flashing again - waiting for the RC signal. At this point follow the instructions of your RC transmitter to turn it on in binding mode. When the RC binding signal is detected, the satellite receivers will follow their routine of binding and blink slower. When the binding is complete, the LED's on the satellite recievers will stay on and on the diversity board will turn off., The package contains:, 1 x MK Diversity Controller, Documentation:, Additional documentation translated by google:, Click here,
This litte diversity controller has been designed to connect 4 ...ngHobbies
GOPRO HERO 3 FPV IMMERSIONRC CABLE WITH POWER
. The USB connector fits the GoPro Hero 3 cameras AV plug and the 5 pin Molex type connector has been provided to be plug and play with the video 2.4GHz and 5.8GHz transmitters designed and manufactured by Immersion RC. The 5 pin Molex connector has the following connections:, Brown - Ground connection, The power requirement for the GoPro camera is minimum 1A at 5V. The provided servo cable connections are:, Red - +5V (Do not exceed 5V), Please note:, The Immersion RC or Fatshark transmitters CANNOT supply enough power on the 5V out line to power the GoPro camera in flight. DO NOT risk it, it will damage your Immersion RC transmitter - or you will loose your transmitter in the air!!!,
Beside the FPV audio and video feed from a GoPro ...ngHobbies
VIDEO OSD PRO EXPANDER
All parameters available with our eLogger V3 and Data Recorders + optional sensors will be supported for display on the OSD Pro. Here are some examples:, GPS Parameters (Distance to Home, Home Arrow, GPS Altitude, Ground Speed,Course, and more), Advanced Features:, The OSD PRO advanced features include "RADAR," Voice Alerts, Return to Home,failsafe, and Waypoints., :, The plane icon labeled “RADAR” above serves two purposes: the direction the icon is pointingindicates your present course. And, the location of the icon on the screen provides a synthetic map, similar to RADAR: the center of the screen marks the takeoff point, in a "bird's eye" view, and the plane icon moves around the screen indicating your model’s location. The maximum distance and the “up” direction is configurable., Voice Alerts/Variometer:, Imagine hearing the status of your model through earbuds connected to your video receiver! The OSD Pro fully supports voice warnings and status updates, via theaudio channel of your video transmitter. Most of the available parameters can be programmed to provide voice alerts., For example, you can program the OSD Pro to periodically update you on altitude once a minute: “Altitude 3-9-1 Feet”. And, you can also program a low voltage warning “WARNING- Voltage 12-point-5 Volts”. Voice alerts can be combined with your camera’s microphone, so you do not lose motor or other flight sounds when there are no alerts., Return to Home and Failsafe:, , Flight Simulator:, A built-in flight simulator is included, letting you fly the RADAR icon around the screen, controlling altitude, throttle and turns with your RC Radio. Since the control surfaces of your model will move at the same time, this feature makes it easier to configure Return to Home and test your alarms and settings, and is also fun on rainy days!, Waypoints:, Up to 3 waypoints (within visual range of the takeoff point) can be programmed into the OSD Pro, for aerial photography or just for fun. The locations of the waypoints are displayed on the RADAR display,
The OSD Pro is a powerful, modular, fully configurable Video/Audio ...ngHobbies
3 PIN CAMERA CABLE WITH IRC TYPE CONNECTOR
This is a replacement 3 pin camera cable for easy installation with Immersion RC EzOSD or any kind of ImmersionRC video transmitters. Will fit most of the KX type cameras: KX-131, KX-171, KX-171-LV and many others. This cable can be used in conjunction with EzOSD providing direct plug of your camera without the need of additional crimping., Note: Please make sure you compare the connections of this cable with your original cable. Please put them side by side and verify that all pins are matching! If not, with a small pin it is very easy to remove and reinsert the terminals in the correct order! Please make sure you verify it, otherwise you can cause damage to your camera!!!!,
ngHobbies
GOPRO HD (1 & 2) FPV IMMERSIONRC CABLE
feed from a GoPro Hero HD camera to an Immersion RC video transmitter. The 2.5mm right angle jack fits the GoPro Hero cameras AV plug and the 5 pin Molex type connector has been provided to be plug and play with the video 2.4GHz and 5.8GHz transmitters designed and manufactured by Immersion RC. The 5 pin Molex connector has the following connections:, Brown - Ground connection,
This cable offers FPV stereo audio and video Red - ...ngHobbies
12V CAMERA HARNESS FOR IMMERSIONRC TRANSMITTERS
Instructions:, Step 1:, Solder the 5 pin cable which came with your ImmersionRC transmitter on your camera: black wire to black wire, red wire to red wire, yellow wire to yellow wire. The green and the white from the connector can be isolated, these are audio wires unless you use a microphone you do not need them. Use a heat shrink to secure the connections., Step2:, Plug the camera cable prepared in step one into the harness. You will need to plug the 2 male connectors of this harness into your InnersionRC or Fatshark tranmsitter, 2 pin connector to the power connection, 5 pin connecto to the A/V connector., Step3:, Plug the 3S (3 cell) LiPo battery into the JST connetor of the harness., Warning:, Do not ever use this harness with 5V cameras. Also make sure you never use more tha 3 cell LiPo's to supply power to this harness. The voltage from the battery is directly fed to the camera, if you use more than 3 cell LiPo you will smoke your camera right away.,
This FPV cable harness offers connection for 12V cameras to ...