Flying-Hobby
REACTOR X2 REGULATOR SYSTEM
The preset CCPM voltages are: 6.0V regulated for all standard and digital servos. 6.8V regulated for high voltage type servos and brushless series servos. In addition the new X2 now allows full unregulated Li-Po voltage (8.4V at full charge) to pass directly to the servos for maximum voltage to HV type servos., Reactor X2 Features and Specifications:,
As the unfailing heart of your helicopter. The Reactor X2 ...Flying-Hobby
T-REX 700E DFC SUPER COMBO
| ●Operating Temperature | -10~60 degree |
| ●X and Y axis Operating Angle Range | -300~+300 degree |
| ●Z axis Operating Angle Range | -600~+600 degree |
| ●Size | 36.5x25.2x15.6 mm Size |
| ●Maximum working voltage | 8.5V |
| ● Length | 1345mm |
| ● Height | 360mm |
| ● Width | 208mm |
| ● Main Blade Length | 690mm |
| ● Main Rotor Diameter | 1562mm |
| ● Tail Rotor Diameter | 281mm |
| ● Motor Drive Gear | 12T |
| ● Main Drive Gear | 112T |
| ● Autorotation Tail Drive Gear | 104T |
| ● Tail Drive Gear | 22T |
| ● Weight(With Motor) | 2900g |
Instruction(3GX Programmable Flybarless System) :, ●Brand new redesigned 3GX represents a new generation of multi function flybarless system. The dramatically improved performance will create immediate impact on any enthusiasts., Specification(3GX Programmable Flybarless System) :, Specification(T-REX 700E DFC) :, ● Drive Gear Ratio: 1:9.33:4.37, Specification(T-REX 700E DFC) :, , Features:, 1. Equipped with the low CG DFC rotor head, effectively reduce wind resistance during flight, providing the most direct and precise control feel back to the pilot, and exhibits exhilarating 3D performance and unimaginable flight speed., Accessories:, ●T-REX 700E DFC Kits Set x 1set, Radio transmitter and electronic equipment required for assembly:, ●Transmitter(7-channel or more, helicopter system),
●3GX is currently the smallest and lightest flybarless system on ...Flying-Hobby
T-REX 600E PRO DFC COMBO
| ●Operating Temperature | -10~60 degree |
| ●X and Y axis Operating Angle Range | -300~+300 degree |
| ●Z axis Operating Angle Range | -600~+600 degree |
| ●Size | 36.5x25.2x15.6 mm Size |
| ●Maximum working voltage | 8.5V |
| ● Length | 1174mm |
| ● Height | 319mm |
| ● Width | 210mm |
| ● Main Blade Length | 600mm |
| ● Main Rotor Diameter | 1347mm |
| ● Tail Rotor Diameter | 260mm |
| ● Motor Drive Gear | 13T |
| ● Main Drive Gear | 112T |
| ● Autorotation Tail Drive Gear | 131T |
| ● Tail Drive Gear | 34T |
| ● Weight(With Motor) | 2290g |
Instruction(3GX Programmable Flybarless System) :, , Specification(3GX Programmable Flybarless System) :, , Specification(T-REX 600E PRO DFC) :, , Specification(T-REX 600E PRO DFC) :, , ● Drive Gear Ratio: 1:8.61:3.85, Accessories:, , Radio transmitter and electronic equipment required for assembly:, ●Transmitter(7-channel or more, helicopter system),
T-REX 600E PRO DFC Kit 1 Castle ICE2 HV 80 ...Flying-Hobby
DEAL - T-REX 700E DFC SUPER COMBO (FREE SHIPPING)
| ●Operating Temperature | -10~60 degree |
| ●X and Y axis Operating Angle Range | -300~+300 degree |
| ●Z axis Operating Angle Range | -600~+600 degree |
| ●Size | 36.5x25.2x15.6 mm Size |
| ●Maximum working voltage | 8.5V |
| ● Length | 1345mm |
| ● Height | 360mm |
| ● Width | 208mm |
| ● Main Blade Length | 690mm |
| ● Main Rotor Diameter | 1562mm |
| ● Tail Rotor Diameter | 281mm |
| ● Motor Drive Gear | 12T |
| ● Main Drive Gear | 112T |
| ● Autorotation Tail Drive Gear | 104T |
| ● Tail Drive Gear | 22T |
| ● Weight(With Motor) | 2900g |
Instruction(3GX Programmable Flybarless System) :, ●Brand new redesigned 3GX represents a new generation of multi function flybarless system. The dramatically improved performance will create immediate impact on any enthusiasts., Specification(3GX Programmable Flybarless System) :, Specification(T-REX 700E DFC) :, ● Drive Gear Ratio: 1:9.33:4.37, Specification(T-REX 700E DFC) :, , Features:, 1. Equipped with the low CG DFC rotor head, effectively reduce wind resistance during flight, providing the most direct and precise control feel back to the pilot, and exhibits exhilarating 3D performance and unimaginable flight speed., Accessories:, ●T-REX 700E DFC Kits Set x 1set, Radio transmitter and electronic equipment required for assembly:, ●Transmitter(7-channel or more, helicopter system),
●3GX is currently the smallest and lightest flybarless system on ...Flying-Hobby
DSX 11 2.4GHZ DSM2 11CH TRANSMITTER & RD921 RECEIVER (MODE 2)
| One transmitter with programming and uncompromised control for all model types | planes, helis and sailplanes |
# of Channels:, 11, Modulation:, DSM2, Band:, 2.400 to 2.483GHz, Servos:, No servos included, Receiver:, JR R921, Model Memory:, 30, expandable with SD card slot, Modes:, Mode 1 or 2, Transmitter (Tx) Battery Type:, 1500mAh 9.6V Ni-MH, Charger:, JR NEC-501C, Input - 100V-240V AC 50/60Hz,
For Helicopters, Gilders and Airplanes of Any Size. This is ...Flying-Hobby
DSX 11 2.4GHZ DSM2 11CH TRANSMITTER & RD921 RECEIVER (MODE 1)
| One transmitter with programming and uncompromised control for all model types | planes, helis and sailplanes |
# of Channels:, 11, Modulation:, DSM2, Band:, 2.400 to 2.483GHz, Servos:, No servos included, Receiver:, JR R921, Model Memory:, 30, expandable with SD card slot, Modes:, Mode 1 or 2, Transmitter (Tx) Battery Type:, 1500mAh 9.6V Ni-MH, Charger:, JR NEC-501C, Input - 100V-240V AC 50/60Hz,
For Helicopters, Gilders and Airplanes of Any Size. This is ...ReadyMadeRC
DJI A2 FLIGHT CONTROLLER SYSTEM AND DJI OSD MKII COMBO
| PLEASE NOTE | This includes qty 1 DJI A2 Multi Rotor Flight Controller AutoPilot System and qty 1 DJI iOSD MkII. |
| The A2 supports 9 types of traditional motor mixer | Quad I, Quad X |
ATTENTION: Despite claims by DJI and other resellers indicating this controller is for commercial use, be aware that it is not currently legal in the US to operate aircraft, even remote controlled like these, commercially without an appropriate FCC waiver or COA. These are sold for amateur use only., Different from other DJI flight controllers, the A2 offers a comprehensive online firmware upgrade ability: the Controller, IMU and GPS Pro, Receiver and Bluetooth LED indicator can be upgraded online through the assistant software separately. Lets you experience the latest technology comprehensively and quickly., It offers three types of control modes: GPS Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. The Flight controller can also adjust automatically within the changing flight environment and intelligently switch between GPS Mode and Atti. Mode to make sure the flight is safe. In manual mode position the operator can choose between manual and attitude. It also supports an RTH Switch from the Transmitter., Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction:, In course lock flying, the forward direction is the same as a recorded nose direction. See the following figures (Mode 2):, In home lock flying, the forward direction is the same as the direction from home point to the multi-rotor. See the following figures (Mode 2):, , A2 has a POI function: Point of Interest. When the GPS signal is good, users can record the current position of the aircraft as a point of interest by a preset switch on the remote controller. The aircraft can achieve a circling flight around the point of interest ,
A2 Multi-rotor Stabilization Controller DJI A2 multi-rotor stabilization controller is ...ReadyMadeRC
DJI A2 MULTI-ROTOR STABILIZATION CONTROLLER
| PLEASE NOTE | This includes qty 1 DJI A2 Multi Rotor Flight Controller AutoPilot System, does not include iOSD. |
| The A2 supports 9 types of traditional motor mixer | Quad I, Quad X |
ATTENTION: Despite claims by DJI and other resellers indicating this controller is for commercial use, be aware that it is not currently legal in the US to operate aircraft, even remote controlled like these, commercially without an appropriate FCC waiver or COA. These are sold for amateur use only., Different from other DJI flight controllers, the A2 offers a comprehensive online firmware upgrade ability: the Controller, IMU and GPS Pro, Receiver and Bluetooth LED indicator can be upgraded online through the assistant software separately. Lets you experience the latest technology comprehensively and quickly., It offers three types of control modes: GPS Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. The Flight controller can also adjust automatically within the changing flight environment and intelligently switch between GPS Mode and Atti. Mode to make sure the flight is safe. In manual mode position the operator can choose between manual and attitude. It also supports an RTH Switch from the Transmitter., Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction:, In course lock flying, the forward direction is the same as a recorded nose direction. See the following figures (Mode 2):, In home lock flying, the forward direction is the same as the direction from home point to the multi-rotor. See the following figures (Mode 2):, , A2 has a POI function: Point of Interest. When the GPS signal is good, users can record the current position of the aircraft as a point of interest by a preset switch on the remote controller. The aircraft can achieve a circling flight around the point of interest w,
A2 Multi-rotor Stabilization Controller DJI A2 multi-rotor stabilization controller is ...ReadyMadeRC
TRANSMITTER MONITOR TRAY - LARGE (WITH HARDWARE)
| Maximum handle size | 105 x 5mm |
Features:, , fit with this mount:,
Finally, a strong and lightweight monitor mount that won't break ...ReadyMadeRC
TRANSMITTER MONITOR TRAY - SMALL (WITH HARDWARE)
| Maximum handle size | 105 x 5mm |
Features:, , fit with this mount:,
Finally, a strong and lightweight monitor mount that won't break ...ReadyMadeRC
NECK STRAP BALANCER FOR MONITOR MOUNT - HORIZONTAL
,
Neck Strap Balancer for Monitor Mount - Horizontal mount style ...ReadyMadeRC
CC3D OPENPILOT COPTERCONTROL BOARD BY READYMADERC (RIGHT ANGLE)
CC3D from the OpenPilot project introduces a hardware refresh of the highly regarded multi-purpose aircraft stabilization platform. The CopterControl platform has been designed from the ground up to perform the following functions:, , The CopterControl hardware has the following features:, , For info:,
CopterControl 3D (CC3D) from the OpenPilot project introduces a new ...ReadyMadeRC
EAGLE TREE - VECTOR FPV CONTROLLER PACKAGE - XT60
| COMPATIBLE | PCM, SPPM and S.BUS |
| FLEXIBLE | fly with or without your FPV equipment |
| REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| Virtual SPPM RSSI | some receivers output RSSI and link quality via the SPPM interface, which is supported |
has everything you've dreamed about, in one small, lightweight product:, , In addition to the graphical features shown above, nearly all of the Vector's parameters can be displayed in 3 ways:, , : The Vector can speak flight information to you periodically, or on programmed alarms., Variometers:, The Vector is the first OSD to provide a charting graphical as well as acoustical tone variometers. The variometers are fully programmable to suit your taste., RSSI:, The Vector supports 4 types of RSSI:, , Fast, easy control and menuing system:, The Vector utilizes switch "gestures" and your control stick to let you rapidly scroll through menus and change parameters. All OSD parameters can be configured via the stick menus!, Kitchen sink:, Of course, all the other OSD features you've come to expect from Eagle Tree, such as RADAR, ladders, compass, full 'F16' AHI, flight simulator, manual waypoints, monitoring of up to four battery voltages, and a huge list of parameters available for display are there in the Vector., The Vector system includes the base controller unit, the GPS/Magnetometer, and the Current Sensor/PSU. The Vector's feature list is quite long, so what follows is an overview of the main features:, Full Color OSD, Smooth, razor sharp color graphics:, tired of staring at hard to read white text with clunky graphics? The Vector changes all that. WARNING: a full color OSD can be addictive! :) Colors are fully adjustable to your preference., Numerous flight modes are available, and are easily selectable via one or more switches on your radio:, 2D:, multirotor or fixed wing leveling with or without altitude and heading hold, 3D:, direct rate 3D with or without heading lock, for doing acrobatics when you get bored just flying along. :) Great for holding 3D positio,
The Vector's wiring harness functions perfectly with RMRC camera and ...ReadyMadeRC
EAGLE TREE - VECTOR FPV CONTROLLER PACKAGE - WIRE LEADS
| COMPATIBLE | PCM, SPPM and S.BUS |
| FLEXIBLE | fly with or without your FPV equipment |
| REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| Virtual SPPM RSSI | some receivers output RSSI and link quality via the SPPM interface, which is supported |
satellites, in addition to other improvements, which can provide the following benefits:, , has everything you've dreamed about, in one small, lightweight product:, , In addition to the graphical features shown above, nearly all of the Vector's parameters can be displayed in 3 ways:, , : The Vector can speak flight information to you periodically, or on programmed alarms., Variometers:, The Vector is the first OSD to provide a charting graphical as well as acoustical tone variometers. The variometers are fully programmable to suit your taste., RSSI:, The Vector supports 4 types of RSSI:, , Fast, easy control and menuing system:, The Vector utilizes switch "gestures" and your control stick to let you rapidly scroll through menus and change parameters. All OSD parameters can be configured via the stick menus!, Kitchen sink:, Of course, all the other OSD features you've come to expect from Eagle Tree, such as RADAR, ladders, compass, full 'F16' AHI, flight simulator, manual waypoints, monitoring of up to four battery voltages, and a huge list of parameters available for display are there in the Vector., The Vector system includes the base controller unit, the GPS/Magnetometer, and the Current Sensor/PSU. The Vector's feature list is quite long, so what follows is an overview of the main features:, Full Color OSD, Smooth, razor sharp color graphics:, tired of staring at hard to read white text with clunky graphics? The Vector changes all that. WARNING: a full color OSD can be addictive! :) Colors are fully adjustable to your preference., Numerous flight modes are available, and are easily selectable via one or more switches on your radio:, 2D:, multirotor or fixed wing leveling with or without altitude and heading hold, 3D:, direct rate 3D with or without heading lock, ,
Now includes V2 GPS unit! (Requires GPS firmware v1.81 update ...ReadyMadeRC
EAGLE TREE - VECTOR FPV CONTROLLER PACKAGE - DEANS
| COMPATIBLE | PCM, SPPM and S.BUS |
| FLEXIBLE | fly with or without your FPV equipment |
| REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| Virtual SPPM RSSI | some receivers output RSSI and link quality via the SPPM interface, which is supported |
satellites, in addition to other improvements, which can provide the following benefits:, , Years in the making, the Vector has everything you've dreamed about, in one small, lightweight product:, , In addition to the graphical features shown above, nearly all of the Vector's parameters can be displayed in 3 ways:, , : The Vector can speak flight information to you periodically, or on programmed alarms., Variometers:, The Vector is the first OSD to provide a charting graphical as well as acoustical tone variometers. The variometers are fully programmable to suit your taste., RSSI:, The Vector supports 4 types of RSSI:, , Fast, easy control and menuing system:, The Vector utilizes switch "gestures" and your control stick to let you rapidly scroll through menus and change parameters. All OSD parameters can be configured via the stick menus!, Kitchen sink:, Of course, all the other OSD features you've come to expect from Eagle Tree, such as RADAR, ladders, compass, full 'F16' AHI, flight simulator, manual waypoints, monitoring of up to four battery voltages, and a huge list of parameters available for display are there in the Vector., The Vector system includes the base controller unit, the GPS/Magnetometer, and the Current Sensor/PSU. The Vector's feature list is quite long, so what follows is an overview of the main features:, Full Color OSD, Smooth, razor sharp color graphics:, tired of staring at hard to read white text with clunky graphics? The Vector changes all that. WARNING: a full color OSD can be addictive! :) Colors are fully adjustable to your preference., Numerous flight modes are available, and are easily selectable via one or more switches on your radio:, 2D:, multirotor or fixed wing leveling with or without altitude and heading hold, 3D:, direct rate 3,
Now includes V2 GPS unit! (Requires GPS firmware v1.81 update ...