ReadyMadeRC
DJI FLAME WHEEL F450 BASIC KIT
Includes | 1× complete frame |
MSRP | $80 |
ReadyMadeRC
DJI FLAME WHEEL F450 ARF KIT INCLUDES MOTORS, ESC & PROPELLERS
MSRP | $80 |
Stator size | 22x12mm |
Current | 30A OPTO |
Signal Frequency | 30Hz ~ 450Hz |
Battery | 3S ~ 4S LiPo |
Dimensions | 10 x 4.5 in; 8 x 4.5 in |
Provide different color frame arms | red, white, black, which makes your flight more colorful. |
Includes:, 4× ESC(30A), 4× Motor(2212), 4× blades(8inch), 4× blades(10inch), 1× complete frame, Flame Wheel F450 ARF Kit Includes:, , KV: 920 rpm/V,
Flame Wheel F450 ARF Kit set $240 FlameWheel series is ...ReadyMadeRC
DJI FLAME WHEEL F330 BASIC KIT
Includes | 1× complete frame |
Frame Only MSRP | $50 |
ReadyMadeRC
DJI FLAME WHEEL F330 ARF KIT INCLUDES MOTORS, ESC & PROPELLERS
Frame Only MSRP | $50 |
Stator size | 22x12mm |
Current | 30A OPTO |
Signal Frequency | 30Hz ~ 450Hz |
Battery | 3S ~ 4S LiPo |
Dimensions | 10 x 4.5 in; 8 x 4.5 in |
Provide different color frame arms | red, white, black, which makes your flight more colorful. |
Includes:, 4× ESC(18A), 4× Motor(2212) ,4× blades(8inch) ,1× complete frame, Flame Wheel F330 ARF Kit Includes:, , KV: 920 rpm/V,
Flame Wheel F330 ARF Kit set $218 FlameWheel series is ...ReadyMadeRC
SKY SURFER 1400 KIT
Wingspan | 1372mm (54 inch) |
Length | 915mm (36 inch) |
Flying Weight | 624g (22 oz) |
Drive System | Not Included (Recommend |
Speed Controller | Not Included (Recommend 30-36A ESC) |
Servos | Not included (Recommend 4x |
Battery | Not Included (Recommend 11.1V 2200mAh Li-Po and remove nose weight) |
Control system | Not Included |
*Note: There are people looking at what they are calling "version 1" and "version 2" of this plane. They really aren't version 1 or 2, but they are just different versions of this plane. Mine are what people are calling version 1, just as the pictures show. This is MUCH better for FPV since there is a ton of space inside the fuselage. The "version 2" planes ruined the usefulness for FPV by putting the servos and control arms inside the fuselage. The tubes for the control arms add strength to the fuselage in this version. My store is focused on FPV, so the equipment I carry will be what is best for FPV! The manufacturer has been a bit inconsistent with the labels: some planes may arrive with the labels already installed., *Not to be distributed or linked to by other companies who like to take other people's work. You know who you are... :),
Airframe Only A super plane for beginners and advanced pilots, ...ReadyMadeRC
FUNJET ULTRA KIT
Specifications | • Wingspan – 31 in. |
Stock # M214245 | FunJet Ultra Kit |
Features:, • Easy to Hand Launch, Easy to Land, Recommended Power System:, FunJet Ultra Power Pack,
Just when you thought your Multiplex FunJet was one of ...ReadyMadeRC
LAYERLENS GOPRO HERO AND HERO2 LENS PROTECTION
For this reason, FPV Manuals has developed LayerLens. LayerLens brings the most important part of the original GoPro case back: the protective lens; without adding much weight or size. LayerLens weighs only 11g — about 10% of the weight of the GoPro case. LayerLens is a precision laser cut frame that holds the protective glass lens found in the GoPro's case. LayerLens is pushed onto the GoPro’s built in lens. It sits tightly in place and is secured by an included velcro band. In case of a crash that scratches LayerLens’ glass lens, you can easily swap out the scratched protective lens and replace it with one of the lenses that are readily available by GoPro as part of their “Lens Replacement Kit” (which includes 2 lenses for $14 to $20 USD).,
Please read the product alert about an identified issue that ...ReadyMadeRC
FATSHARK BASE SD VGA VIDEO GLASSES
interpupillary (ipd) distance | 59-69mm (adjustable) |
power input | 7-13v (2s/3s supply) |
power consumption @12vdc | 100ma |
weight | 120g |
option 1 | the |
Option 3 | Any 2s-3s lipo with a 2.1mm barrell connector like |
package includes:, , specifications:, , Option 2: If you want to share the power supply with your ground station, the included cable allows for that. You simply feed the power from the 2.1mm barrel connector that normally powers your video receiver/ground station into the included cable, and then plug the extra power plug included on the cable into your video receiver/ground station so you are powering both devices with the same battery.,
built for serious fpver’s, the new base sd goggle is ...ReadyMadeRC
DJI WOOKONG MULTI (WK-M) MULTIROTOR CNTRL
Built-In Functions | Autopilot, Auto Hover Fail Safe |
Multi Rotor Types | Quad-Rotor, Hex-Rotor, Octo-Rotor |
Supported ESC output | 200Hz refresh frequencys |
Recommended Transmitter | PCM or 2.4GHz with minimum 5 channels and Failsafe function available on all channels |
Recommended Power Supply | DC 4.8 ~ 12V |
Power Consumption | MAX 5W (0.9A@5V, 0.7A@5.8V,0.5A@7.4V,0.4A@8V) |
Hovering Accuracy | Vertical |
Suitable Wind Condition | < 8m/s (17.7mph) |
Max Rotate Angle | 30° |
Vertical Speed | 3m/s |
Total Weight | <= 150g |
Dimensions | Main Controller |
IMU | 40mm x 31mm x 26mm |
GPS & Compass | 50mm (diameter) x 9mm |
LED Indicator | 25mm x 25mm x 7mm |
Introduction:, , Features:, , Operating Temperature: -5°C to +60°C (You have to keep the IMU warm if you want to use it under low temperature, could be -5°Cor lower.),
DJI Wookong Multi-Rotor stabilization controller is a complete flight system ...ReadyMadeRC
FY-901 MULTI-ROTOR FLIGHT STABILIZATION CONTROLLER
mail us | service |
The FY-901 for multi-rotor copter can be used in the following models:, , :, , The FY-901 has been tested to work well with the following RC system:, , The FY-901Operating Mode for multi-rotor copter supports two flight modes :, , 1: Auto-Stabilization mode., : 3D Control Mode., Gyroscope initialization (re-setting):, , Out of the box, the FY-901 has been fully initialized. However, if the following condition occurs, resetting the gyro is recommended:, , NOTE:,
Introduction FY-901 has integrated three-axis gyro and three-axis accelerometer, which ...ReadyMadeRC
LAYERLENS FOR GOPRO HERO3 (V2)
For this reason, FPV Manuals developed LayerLens. LayerLens brings the most important part of the original GoPro case back: the protective lens; without adding much weight or size. Fully assembled, LayerLens for the GoPro 3 weighs only 7.5g — a small fraction the weight of the full GoPro case. LayerLens has become the standard lens protection product in the fields of RC and FPV where a GoPro is used outside of its standard housing.,
Details This is the new revision of LayerLens for the ...ReadyMadeRC
FINWING PENGUIN ADJUSTABLE MOTOR MOUNT
Position 1 | stock height up to a 9" prop. |
Position 2 | (+) 0.47" for up to a 10" prop. |
Position 3 | (+) .95" for up to an 11" prop. |
Position 4 | (+) 1.42" for up to a 12" prop. |
Total Weight | 38g |
Installation Instructions:, Take the stock wood mount and draw 2 lines going through the existing mounting holes to form an X. This is shown in the attached photos., Included:, 1 - Penguin Base Tube and SSS Motor Plate, 4 motor screws, 4 motor plate screws, 4 base tube screws., Notes:, The stock thrust angles are retained in all 4 positions. If a change in thrust angle is desired, simply add a small washer between the motor base and motor plate at the appropriate locations., Acceptable bolt patterns (units in mm):, 19x19,
This two piece mount is CNC machined from billet aluminum. ...ReadyMadeRC
HITEC H4 DC/DC MULTI-CHARGER 4 PORT MICRO PROCESSOR CHARGER
Stock# 44152 | Flight Power/Thunder Power Battery Adapter |
Stock# 44153 | PolyQuest/HP Battery Adapter |
Stock# 44154 | Molex EH Balancing Adapter |
Stock# 44155 | Molex XH Balancing Adapter |
Stock# 44178 | Universal Balancing Board |
Input Voltage Range:, DC 12 - 18 Volts DC, Required Input Amperage:, 40 Amps / 500 Watts, Charger Circuit Power:, , Discharge Circuit Power:, 10 watts x 4 or 20 watts x 2 Using Channel Bridge Function, Charge Current Range:, , Discharge Current Range:, 0.1 - 2.0 Amps per Channel or 0.1 - 4A Using Channel Bridge Function, LiPo,LiFe & LiIon Balancing Current Drain:, 200mA per Cell, LiPo,LiFe & LiIon Cell Count:, 1 - 6 Cells, Maximum NiCd/NiMh Cell Count:, 1 - 15 Cells, Lead Acid (Pb) Cells / Voltage:, 2 - 20 Volts, Dimensions (W x D x H):, 8.1" x 6.4" x 2.0", Weight:, 3.2 lbs,
Its sleek, aluminum design, easy-to-read backlit graphic display and four ...ReadyMadeRC
GOPROFESSIONAL CASES - PHANTOM/GOPRO HARD CASE
Exterior Dimensions | 20.25" x 16.93" x 8.78" |
Weight | 13.15 lbs |
Features:, All our products are the highest water-jet precision cut. We never cut corners and die-cut or punch cut our custom cases., The XB-DJI Will Fit 9" Props:, 1 DJI Phantom, GoPro Equipment:, 1 Additional GoPro Hero, Specifications:,
Go Professional Cases Introduces the XB-DJIFS The Elite Original Customized ...ReadyMadeRC
DJI PHANTOM LANDING STRUT EXTENSION SET
with included stainless steel hardware | 36.2g |
:, ,
Product Description Add a full inch of height and four ...