SDSHobby
1/10 SCALE RC BRUSHLESS ELECTRIC OFF-ROAD BUGGY CAR RTR #102451 WITH 2.4G RADIO, 4WD SYSTEM, 3900KV MOTOR, 7.2V 3000MAH BATTERY
Technical Parameters:, Gear Rate...................................11.5:1, Features:, Notes:, The servo must be set at the neutral position before assembly. Firstly, turn on the transmitter and receiver in succession; then pull the trim tabs to the neutral position, and turn off the receiver and transmitter, the servo will be at neutral position,
Length.........................................405mm Width...........................................240mm Height.........................................130mm Wheelbase.................................275mm Wheel Diameter..................................88mm*34mm (R)/ 88mm*31mm (F) Tread(F/R)................................. ...SDSHobby
HOBBYWING EZRUN BRUSHLESS SYSTEM COMBO (25A ESC + 2030 12T MOTOR +PROGRAM CARD) FOR 1/18 CAR ON-ROAD RACING CAR/ OFF-ROAD BUGGY
ESC | EZRUN-25A-Sensorless 1pcs |
Motor | EZRUN-2030 12T Brushless motor 1pcs |
Program Card | Digital LEDs Program Card 1pcs |
Output | Continuous current 25A, burst current 90A |
Input | 4-9 cells Ni-MH/NiCd or 2-3 cells LiPo |
BEC Output | 6V/1.5A |
Resistance | 0.005 Ohm |
Motor Supported | Sensorless Brushless motor |
u With 4-6 cells Ni-MH/NiCd or 2 cells Lipo | On-Road≥12T, Off-Road≥18T; |
u With 6-9 cells Ni-MH/NiCd or 3 cells Lipo | On-Road≥18T, Off-Road≥24T; |
Suitable Car | 1/16 or 1/18 scale car for sportful race |
Size | 31.5mm (L) * 27.5mm (W) * 16mm (H) |
Weight (Without wires) | 23g |
With 3 running modes | Racing mode (Forward), Forward/Backward mode and Rock Crawler mode. |
Turns | 12T |
KV value | 7800KV |
Diameter | 20mm |
Motor length | 30mm |
Extend shaft Diameter | 2.0mm |
Length of extend shaft | 10mm |
Weight | 46g |
The Combo Includes the Following Products:, Suitable Brushless Motor:, Features for ESC:, Compatible with all sonsorless brushless motor, Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection., Features for Motor:, Aluminum shell (case),
1/18 or 1/16 Ezrun Brushless ESC for Car 25A : ...SDSHobby
HOBBYWING EZRUN BRUSHLESS SYSTEM COMBO (120A ESC +KV4000 MOTOR +PROGRAM CARD) FOR 1/10 SCT/SCALE SHORT COURSE TRUCK
Force ..." />
Output Current | Continuous 120A, burst 760A |
Input | 6-12 cells Ni-MH/NiCd or 2-4S Lipo |
BEC Output | 6V/3A (Switching mode)* Note #1 |
Resistance | 0.0004 Ohm |
Motor Supported | Sensorless Brushless Motor |
With 6 cells Ni-MH/NiCd or 2S Lipo | KV≤6000; |
With 7-9 cells Ni-MH /NiCd or 3S Lipo | KV≤4000; |
With 10-12 cells Ni-MH /NiCd or 4S Lipo | KV≤3000; |
Suitable Car | 1/10 4WD SCT, 1/8 2WD and 4WD buggy/SCT (Include TRAXXAS 1/10 SCT) |
Size | 59mm (L) * 38mm (W) * 34mm (H) |
Weight | 113g |
* Note #1 | The cooling fan of EZRUN-WP-SC8 is powered by the built-in BEC. |
KV VALUE | KV4000 |
Motor Diameter | 36mm |
Motor Length | 56mm |
Extended Shaft Diameter | 3.17mm |
Extended Shaft Length | 18mm |
Connector Type | 4.0mm Banana Connector |
Voltage | 7.4V (2S LiPo) |
Weight | 210g |
Size | 88mm (L) *58mm (W) *14mm (H) |
Weight | 40g |
EZRUN-WP-SC8 Water-proof ESC:, Suitable Brushless Motor:, Rotor Pole: 4, Program Card:, Input Voltage: 4.8V—6.0V(Battery Pack is needed to supply power for program card, only if the ESC without BEC output.), Programmable Items:, Running Mode,
EZRUN Brushless Sensorless Motor 3656/ KV4000 : Drag Brake Force ...SDSHobby
HOBBYWING EZRUN BRUSHLESS SYSTEM COMBO (120A ESC +KV4700 MOTOR +PROGRAM CARD) FOR 1/10 SCT/SCALE SHORT COURSE TRUCK
Force ..." />
Output Current | Continuous 120A, burst 760A |
Input | 6-12 cells Ni-MH/NiCd or 2-4S Lipo |
BEC Output | 6V/3A (Switching mode)* Note #1 |
Resistance | 0.0004 Ohm |
Motor Supported | Sensorless Brushless Motor |
With 6 cells Ni-MH/NiCd or 2S Lipo | KV≤6000; |
With 7-9 cells Ni-MH /NiCd or 3S Lipo | KV≤4000; |
With 10-12 cells Ni-MH /NiCd or 4S Lipo | KV≤3000; |
Suitable Car | 1/10 4WD SCT, 1/8 2WD and 4WD buggy/SCT (Include TRAXXAS 1/10 SCT) |
Size | 59mm (L) * 38mm (W) * 34mm (H) |
Weight | 113g |
* Note #1 | The cooling fan of EZRUN-WP-SC8 is powered by the built-in BEC. |
KV VALUE | KV4700 |
Motor Diameter | 36mm |
Motor Length | 56mm |
Extended Shaft Diameter | 3.17mm |
Extended Shaft Length | 18mm |
Connector Type | 4.0mm Banana Connector |
Voltage | 7.4V (2S LiPo) |
Weight | 205g |
Size | 88mm (L) *58mm (W) *14mm (H) |
Weight | 40g |
EZRUN-WP-SC8 Water-proof ESC:, Suitable Brushless Motor:, Rotor Pole: 4, Program Card:, Input Voltage: 4.8V—6.0V(Battery Pack is needed to supply power for program card, only if the ESC without BEC output.), Programmable Items:, Running Mode,
EZRUN Brushless Sensorless Motor 3656/ KV4700 : Drag Brake Force ...SDSHobby
HOBBYWING EZRUN BRUSHLESS SYSTEM COMBO (120A ESC +KV2000 MOTOR +PROGRAM CARD) FOR 1/10 SCT/SCALE SHORT COURSE TRUCK
Force ..." />
Output Current | Continuous 120A, burst 760A |
Input | 6-12 cells Ni-MH/NiCd or 2-4S Lipo |
BEC Output | 6V/3A (Switching mode)* Note #1 |
Resistance | 0.0004 Ohm |
Motor Supported | Sensorless Brushless Motor |
With 6 cells Ni-MH/NiCd or 2S Lipo | KV≤6000; |
With 7-9 cells Ni-MH /NiCd or 3S Lipo | KV≤4000; |
With 10-12 cells Ni-MH /NiCd or 4S Lipo | KV≤3000; |
Suitable Car | 1/10 4WD SCT, 1/8 2WD and 4WD buggy/SCT (Include TRAXXAS 1/10 SCT) |
Size | 59mm (L) * 38mm (W) * 34mm (H) |
Weight | 113g |
* Note #1 | The cooling fan of EZRUN-WP-SC8 is powered by the built-in BEC. |
KV VALUE | KV2000 |
Motor Diameter | 42mm |
Motor Length | 74mm |
Extended Shaft Diameter | 3.17mm |
Extended Shaft Length | 18mm |
Connector Type | 4.0mm Banana Connector |
Voltage | 7.4V (2S LiPo) |
Size | 88mm (L) *58mm (W) *14mm (H) |
Weight | 40g |
EZRUN-WP-SC8 Water-proof ESC:, Suitable Brushless Motor:, Rotor Pole: 4, Program Card:, Input Voltage: 4.8V—6.0V(Battery Pack is needed to supply power for program card, only if the ESC without BEC output.), Programmable Items:, Running Mode,
EZRUN Brushless Sensorless Motor 4274/ KV2000 : Drag Brake Force ...SDSHobby
HOBBYWING EZRUN BRUSHLESS SYSTEM COMBO (120A ESC +KV3400 MOTOR +PROGRAM CARD) FOR 1/10 SCT/SCALE SHORT COURSE TRUCK
Force ..." />
Output Current | Continuous 120A, burst 760A |
Input | 6-12 cells Ni-MH/NiCd or 2-4S Lipo |
BEC Output | 6V/3A (Switching mode)* Note #1 |
Resistance | 0.0004 Ohm |
Motor Supported | Sensorless Brushless Motor |
With 6 cells Ni-MH/NiCd or 2S Lipo | KV≤6000; |
With 7-9 cells Ni-MH /NiCd or 3S Lipo | KV≤4000; |
With 10-12 cells Ni-MH /NiCd or 4S Lipo | KV≤3000; |
Suitable Car | 1/10 4WD SCT, 1/8 2WD and 4WD buggy/SCT (Include TRAXXAS 1/10 SCT) |
Size | 59mm (L) * 38mm (W) * 34mm (H) |
Weight | 113g |
* Note #1 | The cooling fan of EZRUN-WP-SC8 is powered by the built-in BEC. |
KV Value | KV3400 |
Motor Diameter | 36mm |
Motor Length | 56mm |
Extended Shaft Diameter | 3.17mm |
Extended Shaft Length | 18mm |
Connector Type | 4.0mm Banana Connector |
Voltage | 7.4V (2S LiPo) |
Weight | 210g |
Size | 88mm (L) *58mm (W) *14mm (H) |
Weight | 40g |
EZRUN-WP-SC8 Water-proof ESC:, Suitable Brushless Motor:, Rotor Pole: 4, Program Card:, Input Voltage: 4.8V—6.0V(Battery Pack is needed to supply power for program card, only if the ESC without BEC output.), Programmable Items:, Running Mode,
EZRUN Brushless Sensorless Motor 3656/ KV3400 : Drag Brake Force ...SDSHobby
LARGER IMAGE EZRUN BRUSHLESS SYSTEM(18A ESC+12T/2030 MOTOR+DIGITAL PROGRAM CARD) FOR 1/18 CAR (VERISON 2.0)
Length of extend shaft | 10mm |
With 3 running modes | Racing |
Multiple protection features | Low voltage cut-off |
1/18 Ezrun Brushless Esc For Car 18A:, Output:, Continuous current 18A, burst current 50A, Input:, 4-9 cells Ni-MH/NiCd or 2-3 cells LiPo, BEC Output:, 6V/1A, Resistance:, 0.01 Ohm, Motor Supported:, Sensorless Brushless motor, Suitable Brushless Motor:, , With 4-6 cells Ni-MH/NiCd or 2 cells Lipo:, On-Road, With 6-9 cells Ni-MH/NiCd or 3 cells Lipo:, On-Road, Suitable Car:, 1/16 or 1/18 scale car for sportful race, Size:, 31.5mm, (Without wires):, 19g, 1/18 and 1/16 EZRUN-2030 Brushless Motor for Car 12T:, Turns:, 12T, KV value:, 7800KV, Diameter:, 0mm, Motor length:, 30mm, Extend shaft Diameter:, .0mm, Weight:, 46g, Features for ESC:, Features for Motor:,
u ≥ 12T, Off-Road ≥ 18T; u ≥ 18T, Off-Road ...SDSHobby
EZRUN BRUSHLESS SYSTEM(25A ESC+18T/2030 MOTOR+DIGITAL PROGRAM CARD) FOR 1/18 1/16 CAR (VERISON 2.0)
With 3 running modes | Racing |
Multiple protection features | Low voltage cut-off |
1/18 Ezrun Brushless ESC for Car 25A:, Output:, Continuous current 25A, burst current 90A, Input:, 4-9 cells Ni-MH/NiCd or 2-3 cells LiPo, BEC Output:, 6V/1.5A, Resistance:, 0.005 Ohm, Motor Supported:, Sensorless Brushless motor, Suitable Brushless Motor:, , With 4-6 cells Ni-MH/NiCd or 2 cells Lipo:, On-Road, With 6-9 cells Ni-MH/NiCd or 3 cells Lipo:, On-Road, Suitable Car:, 1/16 or 1/18 scale car for sportful race, Size:, , (Without wires):, 3g, 1/18 and 1/16 EZRUN-2030 Brushless Motor for Car 12T:, Turns:, 12T, KV value:, 7800KV, Diameter:, 0mm, Motor length:, 30mm, Extend shaft Diameter:, .0mm, Length of extend shaft:, 10mm, Weight:, 46g, Features for ESC:, Features for Motor:,
u ≥ 12T, Off-Road ≥ 18T; u ≥ 18T, Off-Road ...SDSHobby
EZRUN BRUSHLESS SYSTEM(18A ESC+18T/2030 MOTOR+DIGITAL PROGRAM CARD) FOR 1/18 CAR (VERISON 2.0)
Length of extend shaft | 10mm |
With 3 running modes | Racing |
Multiple protection features | Low voltage cut-off |
1/18 EZRUN BRUSHLESS ESC FOR CAR 18A:, Output:, Continuous current 18A, burst current 50A, Input:, 4-9 cells Ni-MH/NiCd or 2-3 cells LiPo, BEC Output:, 6V/1A, Resistance:, 0.01 Ohm, Motor Supported:, Sensorless Brushless motor, Suitable Brushless Motor:, , With 4-6 cells Ni-MH/NiCd or 2 cells Lipo:, On-Road, With 6-9 cells Ni-MH/NiCd or 3 cells Lipo:, On-Road, Suitable Car:, 1/16 or 1/18 scale car for sportful race, Size:, 31.5mm, (Without wires):, 19g, 1/18 EZRUN-2030Brushless Motor for Car 18T:, Turns:, 18T, KV value:, 5200KV, Diameter:, 0mm, Motor length:, 30mm, Extend shaft Diameter:, .0mm, Weight:, 46g, Features for ESC:, Features for Motor:,
u ≥ 12T, Off-Road ≥ 18T; u ≥ 18T, Off-Road ...SDSHobby
EZRUN-150A-SD BRUSHLESS ESC FOR 1/5 CAR (COMPETITION RACE)
Model | EZRUN-150A-SD Brushless ESC for 1/5 Car (Competition Race) |
Manual | User Manual |
Accessory | Program Card for Car ESC |
1.1 Output | Continuous current 150A, burst current 1080A. |
1.2 Input | 6-18 cells NiMH/NiCd or 2-6 cells LiPo. |
1.3 BEC Output | 5.75V/3A (Switch mode built-in BEC). |
1.4 Resistance | 0.0002 Ohm. |
1.5 Motor Supported | Sensorless and sensored brushless motors |
1.6 Suitable Brushless Motor | 6T and > 6T |
1.7 Suitable Car | 1/5 on-road or off-road cars / trucks for competitive race. |
1.8 Size | 68mm(L) * 55mm(W) * 45mm(H). |
1.9 Weight | 150g(Without wires) |
1.7 Multiple protection features | Low voltage cut-off protection / Over-heat protection |
SDSHobby
EZRUN-60A-SL BRUSHLESS ESC FOR 1/12 AND 1/10 CARS (VERSION 2.0)
Model | EZRUN-60A-SL Brushless ESC for 1/12 and 1/10 Cars (Version 2.0) |
Manual | User Manual |
Accessory | Program Card for Car ESC |
1.1 Output | Continuous current 60A, burst current 380A. |
1.2 Input | 4-9 cells NiMH/NiCd or 2-3 cells LiPo. |
1.3 BEC Output | 6V/1.5A. |
1.4 Resistance | 0.0007 Ohm. |
1.5 Motor Supported | Sensorless Brushless Motor |
With 4-6 cells NiMH/NiCd or 2 cells Lipo | On-Road≥5.5T, Off-Road≥8.5T; |
With 6-9 cells NiMH/NiCd or 3 cells Lipo | On-Road≥8.5T, Off-Road≥13T; |
1.7 Suitable Car | 1/12, 1/10 on-road or off-road cars / trucks for normal race or sportful race. |
1.8 Size | 31.5mm(L) * 27.5mm(W) * 24mm(H). |
1.9 Weight | 32g(Without wires) |
.4 With 3 running modes | Racing mode (Forward), Forward/Backward mode and |
.8 Multiple protection features | Low voltage cut-off protection for lithium or nickel |
1.6 Suitable Brushless Motor:,
1 Specification Features.1 Compatible with all sonsorless brushless motor..2 Use ...SDSHobby
EZRUN-35A-SL BRUSHLESS ESC FOR 1/12 AND 1/10 CARS (VERSION 2.0)
Model | EZRUN-35A-SL Brushless ESC for 1/12 and 1/10 Cars (Version 2.0) |
Manual | User Manual |
Accessory | Program Card for Car ESC |
1.1 Output | Continuous current 35A, burst current 190A. |
1.2 Input | 4-9 cells NiMH/NiCd or 2-3 cells LiPo. |
1.3 BEC Output | 6V/1.5A. |
1.4 Resistance | 0.0015 Ohm. |
1.5 Motor Supported | Sensorless Brushless Motor |
With 4-6 cells NiMH/NiCd or 2 cells Lipo | On-Road≥9T, Off-Road≥12T; |
With 6-9 cells NiMH/NiCd or 3 cells Lipo | On-Road≥12T, Off-Road≥18T; |
1.7 Suitable Car | 1/12, 1/10 on-road or off-road cars / trucks for normal race or sportful race. |
1.8 Size | 31.5mm(L) * 27.5mm(W) * 24mm(H). |
1.9 Weight | 30g(Without wires) |
.4 With 3 running modes | Racing mode (Forward), Forward/Backward mode and Rock |
.8 Multiple protection features | Low voltage cut-off protection for lithium or battery /Over-heat |
1.6 Suitable Brushless Motor:,
1 Specification Features.1 Compatible with all sonsorless brushless motor..2 Use ...SDSHobby
EZRUN-25A-SL-L BRUSHLESS ESC FOR 1/18 CAR (VERSION 2.0)
Model | EZRUN-25A-SL-L Brushless ESC for 1/18 Car (Version 2.0) |
Manual | User Manual |
Accessory | Program Card for Car ESC |
1.1 Output | Continuous current 25A, burst current 90A. |
1.2 Input | 4-9 cells NiMH/NiCd or 2-3 cells LiPo. |
1.3 BEC Output | 6V/1.5A. |
1.4 Resistance | 0.005 Ohm. |
1.5 Motor Supported | Sensorless Brushless Motor |
With 4-6 cells NiMH/NiCd or 2 cells Lipo | On-Road≥12T, Off-Road≥18T; |
With 6-9 cells NiMH/NiCd or 3 cells Lipo | On-Road≥18T, Off-Road≥24T; |
1.7 Suitable Car | 1/16, 1/18 on-road or off-road cars / trucks for normal race or sportful race. |
1.8 Size | 31.5mm(L) * 27.5mm(W) * 16mm(H). |
1.9 Weight | 23g(Without wires) |
.4 With 3 running modes | Racing mode (Forward), Forward/Backward mode and Rock Crawler mode. |
1.6 Suitable Brushless Motor:, .8 Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection.,
Preview 1 Specification Features .1 Compatible with all sonsorless brushless ...SDSHobby
EZRUN-25A-SL-H BRUSHLESS ESC FOR 1/12 AND 1/10 CARS (VERSION 2.0)
Model | EZRUN-25A-SL-H Brushless ESC for 1/12 and 1/10 Cars (Version 2.0) |
Manual | User Manual |
Accessory | Program Card for Car ESC |
1.1 Output | Continuous current 25A, burst current 90A. |
1.2 Input | 4-9 cells NiMH/NiCd or 2-3 cells LiPo. |
1.3 BEC Output | 6V/1.5A. |
1.4 Resistance | 0.005 Ohm. |
1.5 Motor Supported | Sensorless Brushless Motor |
With 4-6 cells NiMH/NiCd or 2 cells Lipo | On-Road≥12T; |
With 6-9 cells NiMH/NiCd or 3 cells Lipo | On-Road≥18T; |
1.7 Suitable Car | RTR application for 1/12, 1/10 on-road cars |
1.8 Size | 31.5mm(L) * 27.5mm(W) * 24mm(H). |
1.9 Weight | 30g(Without wires) |
.4 With 3 running modes | Racing mode (Forward), Forward/Backward mode and Rock Crawler mode. |
1.6 Suitable Brushless Motor:, .8 Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection.,
Preview EZRUN-25A-SL-L is specially designed for RTR application of 1/12 ...SDSHobby
EZRUN-18A-SL BRUSHLESS ESC FOR 1/18 CAR (VERSION 2.0)
Model | EZRUN-18A-SL Brushless ESC for 1/18 Car (Version 2.0) |
Manual | User Manual |
Accessory | Program Card for Car ESC |
1.1 Output | Continuous current 18A, burst current 50A. |
1.2 Input | 4-9 cells NiMH/NiCd or 2-3 cells LiPo. |
1.3 BEC Output | 6V/1A. |
1.4 Resistance | 0.01 Ohm. |
1.5 Motor Supported | Sensorless Brushless Motor |
With 4-6 cells NiMH/NiCd or 2 cells Lipo | On-Road≥12T, Off-Road≥18T; |
With 6-9 cells NiMH/NiCd or 3 cells Lipo | On-Road≥18T, Off-Road≥24T; |
1.7 Suitable Car | 1/18 on-road or off-road cars / trucks for normal race or sportful race. |
1.8 Size | 31.5mm(L) * 24mm(W) * 15mm(H). |
1.9 Weight | 19g(Without wires) |
.4 With 3 running modes | Racing mode (Forward), Forward/Backward mode and Rock Crawler mode. |
1.6 Suitable Brushless Motor:, .8 Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection.,
Preview 1 Specification Features .1 Compatible with all sonsorless brushless ...