ngHobbies
MK LED DRIVER
| http | //vimeo.com/22063018 |
The Distribution boards for Mikrokopter Quads and Mikrokopter Okto does not have built in LED control as the distribution board for Hexa and Hexa XL. This little circuit was designed to be soldered on top of the distribution board along the BL controller number 3. With it's low profile and very small footprint it is almost invisible - but it gies an extra feature to your Mikrokopter - the possibility to control the LED's underneath from switches of the remote control - or based on fucntions being activated. One could achieve the following setup:, Free flight - no LED's on, The package contains:, 1 x MK LED Driver Board, Documentation:, Setup and installation guide:, Click here to download or open, :,
GPS position hold - LED's slowly flashing Coming home - ...ngHobbies
RED ALU RIGGER FOR 500MM MK FRAME
,
This is the red aluminum rigger only, for the 500mm ...ngHobbies
EPP1345 CF PROPELLER PAIR
| - External diameter | 13" |
| - Pitch | 4.5" |
| - Mounting hole | 5mm |
Technical Data:, Package contains:, One pair of counter rotating propellers (one of each direction - total 2),
This is a pair of the new sturdy 13" left ...ngHobbies
RED ALU RIGGER FOR MK HEXA
,
This is the Red aluminum rigger only, for the Mikrokopter ...ngHobbies
MKGPS 5CM CABLE ONLY
,
This package contains a replacement cable for the MKGPS. Please ...BevRC
LOTUS T580 (NEWEST VERSION)
| http | //www.rcgroups.com/forums/showthread.php?t=1384681 |
| Reviews | http |
| and http | //www.rcmodelreviews.com/lotus_t580_review.shtml |
The support thread here:,
. If you are looking for a stable, easy to ...BevRC
FPV QUAD MF450
Download the manual here:, , The upper base board: reserve the holes to fix naza, WKM or YS-X6(YS-X4) gps stand, there is an ALU-made camera mount for FPV camera in front , 38*38mm or 33*33mm, you can mount a 3s 5000mAh in center, there is place for video Tx in the back side., The lower base board: You can set up 1-4 control borads for quad(FF, KK, MWC etc), also with power dispatch board, extension board etc, also reserve the holes for holding the ultrasonic sensors, place to mount Naza or YS-X4. You can put a 2200mah in this board, reserve holds to add high landing gears, easy to add., Support 12-inch props at most, your purchase includes:, 1* upper and lower base board,
Design specially for FPV use, clear view camera mount, 2-axis ...BevRC
BEV 1540 CARBON FIBER CW/CWW PROPELLERS PAIR
Includes:, 1* CW 1540 carbon prop,
Super robust 3K Japanese carbon fiber built, well balanced, light ...BevRC
BEV 1365 CARBON FIBER CW/CWW PROPELLERS PAIR
Includes:, 1* CW 1365 carbon prop,
Super robust 3K Japanese carbon fiber built, well balanced, light ...BevRC
GF 1245 NYLON-CARBON CW/CWW PROPELLER PAIR
Your purchase will include:, 1 pair of 1245 CW/CWW props,
Forget the colorful soft propellers for multi-coptors, the black Nylon-carbon ...BevRC
T80 STOCK BATTERY FULLYMAX 2S 800MAH LIPO
,
The fullymax 2s 800mah, with JST connector, plug and play ...HobbyKing
MICRO 3D SINGLE AXIS THRUST VECTORING MOTOR MOUNT
| Motor to mount hole spacing | 32mm diagonal |
| Firewall hole spacing | 32mm diagonal |
| Standoff from firewall | 16.5mm |
| Weight | 3.1g |
Spec:,
Looking for something REALLY different for your 3D foamie? Check ...5 Reviews