ReadyMadeRC
CAMERA CABLE (4-WIRE,6PIN FOR OLD VERSION RMRC-700XV)
PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera you need to use a regulator before the cable.,
This is a 4-wire camera lead with a 6 pin ...ReadyMadeRC
CAMERA CABLE (4-WIRE, FOR CAMERAS WITH AUDIO)
Directly compatible with the following cameras:, RMRC-600XV, RMRC-540, RMRC-480, RMRC-420 (not 420xv), PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera you need to use a regulator before the cable.,
This is a 4-wire camera lead compatible with many different ...ReadyMadeRC
HORNET OSD + FY31AP (FY-31AP TRADE EDITION)
| For FY-21AP | Fixed Altitude flying mode; for FY-3ZT/FY-31AP |
| GPS speed (Unit | km/h) |
| Current latitude and longitude of the plane (Format | “dddmm.mmm” ) |
| The angle of turning to the return point (Unit | deg) |
| Total flight time (Format | “mm.ss”) |
| Course angle of flight (Unit | deg) |
| Operating temperature(Unit | ℃) |
| (Unit | mA / h) |
| Climb rate (Unit | m/s) |
| Inputvoltage | 4.0 ~ 6.0 Volt; |
| Currentdraw | 50mA (5V); |
| Size | 47x 27x 20 mm; |
| Weight (excluding wires) | 25g; |
| Temperature range | -25 ° C ~ +70 ° C; |
| Maximum rate of rotation | ≤ 2000 ° /s |
| Input voltage | 3.0 ~ 3.3 Volt; |
| Currentdraw | 60mA (3.3V); |
| Size | 32 x32x 10 mm; |
| Weight (excluding wires) | 22g; |
| Temperature range | -25 ° C ~ +70 ° C; |
The telemetry data is as below:, , Relative altitude (Unit : m), Distance to take-off Point (Unit : m), The battery voltage of the video transmitter (Unit: V), Power battery voltage (Unit: V), Power battery current (Unit: A), The OSD can be controlled to show different display information via one spare channel of your radio Rx. There are 5 optional display modes controlled by the different PWM signals. You can use default mode if you do not want to change the display modes.(the 5 modes separately are as following: A. All Information Displayed; B., The modes are shown as below:, , By using your remote control, the FY-31AP can be turned on or off for the following functions:, , The FY-31AP provides an optional upgrade combining with the FY-OSD and the Data Radio. With this add-on, you will receive:, , :, GPS module:, The FY-31AP can be installed in the following aircraft :, , Any other configuration , please e-mail us for enquiry:, service@feiyu-tech.com, The FY-31AP has been tested to work with the following RC systems:, , Includes:,
Brief Introduction The Hornet- OSD overlays flight telemetry information onto ...ReadyMadeRC
M.I.G. TRACKER (MAGNETIC, INERTIAL, GYRO) (V4)
| Power supply range | 2s-3s LiPo |
ReadyMadeRC
FAT SHARK DOMINATOR HEAD TRACKER MODULE
,
Head tracker module for the FatShark Dominator video glasses. When ...ReadyMadeRC
FAT SHARK PREDATOR VIDEO GLASSES
| FOV (field of view) | 25 degrees diagonal |
| Interpupillary (IPD) distance | 63.5mm (fixed) |
| Optional diopter lens inserts | -2, -4, -6 dpt Image size |
| User Controls | Channel selection |
| Power supply | 7 - 13 V (2S/3S supply) |
| Power consumption (@7.4V nominal) | 300mA wireless mode |
| Weight | 150g |
| Note | Fat Shark headsets use Airwaves brand RF modules. |
Package includes:, Predator goggles with integrated 5.8GHz receiver and MIG V4 head tracker, Optics:, Audio:, Stereo (optional headphones available, Electrical:, Antennae:, External (dipole included or circular polarized compatible), Mechanical:, Ergonomic molded headset, Head Tracker:, M.I.G. (magnetic/ inertial/ gyro) V4, Interface:, 3.5mm AV in/out port, Operating Frequencies:, 5.8 Ghz Receiver Module,
Closeout pricing, cannot be back-ordered. FREE SHIPPING! FatShark quality on ...ReadyMadeRC
FAT SHARK DOMINATOR VIDEO GLASSES
Features:, Form fitting silicone eye cups, Note for warranty claims for goggles:, The screens in all types of video goggles are susceptible to damage from the sun. Care should be taken to avoid direct sunlight into the eyepieces. Dead or damaged pixels from sun damage are not covered under the manufacturers warranty. Also, from time to time there may be a dead pixel on any LCD display. An isolated dead pixel is not covered under warranty or replacement. Only display issues that affect the picture quality such as multiple pixels are covered under warranty, and any groups of dead pixels must be reported within 1 week of receipt of the goggles.,
Experience the new Dominator; an innovative 3rd generation FPV headset ...ReadyMadeRC
FAT SHARK ATTITUDESD VGA VIDEO GLASSES
| Note | Battery, charger and adjustable earphones are sold separately. |
| Option 1 | The |
| Option 2 | If you want to share the power supply with your ground station, the |
| Option 3 | Any 2s-3s lipo with a 2.1mm barrell connector like |
| Interpupillary (IPD) distance | 59-69mm (adjustable) |
| Power input | 7-13V (2s/3s supply) |
| Power Consumption @7.4VDC | 200/350mA (direct/wireless) |
| Weight | 150g |
| Power Supply | 7-13V (2s-3s supply) |
| Power consumption | 310mA@7.4VDC |
| Transmitting Power | 250mW |
| Ch1 | 5740, CH2 |
| Mechanical | 55x26x11mm |
| Weight | 22g with antenna |
Features: Adjustable IPD, 35 degree FOV VGA display, secured rubber eyecups, lightweight, integrated 5G8 receiver and MIG V4 head tracker., Kit includes:, AtttitudeSD headset (with RX and HT) (Uses the high performance NexWaveRF receiver module), *Notice: The use and operation of this product in the USA and other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
AttiudeSD (VGA, 640X480) FPV goggle with adjustable IPD, large 35 ...ReadyMadeRC
DRAGONLINK 2 LONG RANGE UHF RECEIVER
Includes:, 1 Long Range Receiver with Antenna, Notice: The use and operation of this product in the USA and many other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Ready Made RC, LLC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
One of the most popular long range UHF R/C systems, ...ReadyMadeRC
DRAGONLINK 2 LONG RANGE UHF RC SYSTEM
Includes:, 1 Transmitter Module, Notice: The use and operation of this product in the USA and many other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Ready Made RC, LLC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
One of the most popular long range UHF R/C systems, ...ReadyMadeRC
FATSHARK BASE SD VGA VIDEO GLASSES
| interpupillary (ipd) distance | 59-69mm (adjustable) |
| power input | 7-13v (2s/3s supply) |
| power consumption @12vdc | 100ma |
| weight | 120g |
| option 1 | the |
| Option 3 | Any 2s-3s lipo with a 2.1mm barrell connector like |
package includes:, , specifications:, , Option 2: If you want to share the power supply with your ground station, the included cable allows for that. You simply feed the power from the 2.1mm barrel connector that normally powers your video receiver/ground station into the included cable, and then plug the extra power plug included on the cable into your video receiver/ground station so you are powering both devices with the same battery.,
built for serious fpver’s, the new base sd goggle is ...ReadyMadeRC
TSLRS TX600+ UHF TRANSMITTER
| Transmitter power 3 steps | 0.5W 1W and 2Watts |
| Watt / SupplyVolt = Current, the supply voltage can be anything from 6-25V. Example with a 3S lipo | 1.5W / 11V = 0.126A |
Example: 1000mAh / 126mA = 7.9 hrs, remember to keep a good safe margin, some batteryes like LIPO do not like to be fully empty., Notice: The use and operation of this product in the USA and many other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
Now able to handle any PPM signal input, with no ...ReadyMadeRC
FY-901 MULTI-ROTOR FLIGHT STABILIZATION CONTROLLER
| mail us | service |
The FY-901 for multi-rotor copter can be used in the following models:, , :, , The FY-901 has been tested to work well with the following RC system:, , The FY-901Operating Mode for multi-rotor copter supports two flight modes :, , 1: Auto-Stabilization mode., : 3D Control Mode., Gyroscope initialization (re-setting):, , Out of the box, the FY-901 has been fully initialized. However, if the following condition occurs, resetting the gyro is recommended:, , NOTE:,
Introduction FY-901 has integrated three-axis gyro and three-axis accelerometer, which ...ReadyMadeRC
CC3D OPENPILOT COPTERCONTROL BOARD BY READYMADERC
CC3D from the OpenPilot project introduces a hardware refresh of the highly regarded multi-purpose aircraft stabilization platform. The CopterControl platform has been designed from the ground up to perform the following functions:, A MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters, The CopterControl hardware has the following features:, Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM, For info:,
CopterControl 3D (CC3D) from the OpenPilot project introduces a new ...ReadyMadeRC
M.I.G. TRACKER V4 (MAGNETIC, INERTIAL, GYRO)
| Power supply range | 2s-3s LiPo |