Futaba SDSHobby Page 7 Review

SDSHobby

PIXHAWK PIX PXI PX4 OPEN-HARDWARE AUTOPILOT FLIGHT CONTROLLER SET (AUTOPILOTS FC/ CONTROL BOARD WITH 6H GPS) FOR RC AIRPLANE/ MULTICOPTER

. CPU	168MHZ, 256K RAM

Kindly Remark:, 1. The product is, :, Their positioning accuracy, speed and sensitivity are the same. The only difference is that, Weight and Sizes:, 1. Weight:, 38g (not include GPS), . Width:, 50mm, 3. Height:, 15.5mm, 4. Length:, 81.5mm, Features:, 1. Advanced, Hardware Specifications:, Processor:, 1. 32-bit 2 Mega STM32F427 Cortex M4 core with FPU, Interfaces:, 1. 5 x UART (serial ports), one high-power capable, 2x with HW flow control, Attention:, Pixhawk is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers (and all those sold by 3D Robotics) allow for PPM output, but some, such as non-S.BUS Futaba receivers, do not.,

open-hardware and not support sales return after selling out. If ...

SDSHobby

3 LINE SMALL POWER SWITCH WITH CHARGING FUNCTION

Features:, Wire Length:, 00mm, 200mm, 200mm, Plug Type:, Futaba cathode plug, 2pcs JR anode plugs,

Built-in charging function

SDSHobby

GENSACE NI-MH AA 2700MAH 4.8V 4S NI-MH COMMON BATTERY FOR RC MODEL RECEIVER BATTERY AND OTHER ELECTRICAL TOYS

Capacity	2700mAh
Voltage	4.8V
Single size	Dia 14.5mm Ht. 50.5mm
Single weight	29g
Discharge current	5C; MAX Discharge current
Connector	FUTABA connector, and the connector can be customized according to customer demand
Usage	Suitable for all kinds of remote control receiver battery and other electrical toys
Charger	You can use a simple charger or smart charger

Parameters:,

SDSHobby

GENSACE NI-MH AAA 800MAH 9.6V 8S NI-MH POWER BATTERY FOR RC MODEL RECEIVER BATTERY AND OTHER ELECTRICAL TOYS

Capacity	800mAh
Voltage	9.6V
Single size	Dia 10.5mm Ht. 44.5mm
Single weight	10g
Discharge current	10C; MAX Discharge current
Connector	FUTABA connector, and the connector can be customized according to customer demand
Usage	Suitable for all kinds of remote control receiver battery and other electrical toys
Charger	You can use a simple charger or smart charger

Parameters:,

SDSHobby

GENSACE NI-MH AA 2000MAH 9.6V 8S NI-MH BATTERY (LONG TIME USAGE AFTER WELL CHARGED) FOR RC MODEL RECEIVER BATTERY AND OTHER ELECTRICAL TOYS

Capacity	2000mAh
Voltage	9.6V
Single size	Dia 14.5mm Ht. 50.5mm
Single weight	27g
Discharge current	5C; MAX Discharge current
Connector	FUTABA connector, and the connector can be customized according to customer demand
Usage	Suitable for all kinds of remote control receiver battery and other electrical toys
Charger	You can use a simple charger or smart charger

Parameters:,

SDSHobby

GENSACE NI-MH AA 2000MAH 9.6V 8S NI-MH POWER BATTERY FOR RC MODEL RECEIVER BATTERY AND OTHER ELECTRICAL TOYS

Capacity	2000mAh
Voltage	9.6V
Single size	Dia 14.5mm Ht. 50.5mm
Single weight	25g
Discharge current	10C; MAX Discharge current
Connector	FUTABA connector, and the connector can be customized according to customer demand
Usage	Suitable for all kinds of remote control receiver battery and other electrical toys
Charger	You can use a simple charger or smart charger

Parameters:,

SDSHobby

GENSACE NI-MH AA 2000MAH 4.8V 4S NI-MH POWER BATTERY FOR RC MODEL RECEIVER BATTERY AND OTHER ELECTRICAL TOYS

Capacity	2000mAh
Voltage	4.8V
Single size	Dia 14.5mm Ht. 50.5mm
Single weight	25g
Discharge current	10C; MAX Discharge current
Connector	FUTABA connector, and the connector can be customized according to customer demand
Usage	Suitable for all kinds of remote control receiver battery and other electrical toys
Charger	You can use a simple charger or smart charger

Parameters:,

SDSHobby

GENSACE NI-MH 2/3A 1600MAH 4.8V 4S NI-MH POWER BATTERY FOR RC MODELS

Capacity	1600mAh
Voltage	4.8V
Single size	Dia 17mm Ht. 28.5mm
Single weight	10g
Discharge current	10C; MAX Discharge current
Connector	FUTABA connector, and the connector can be customized according to customer demand
Usage	Suitable for all kinds of remote control model
Charger	You can use a simple charger or smart charger

Parameters:,

SDSHobby

L SHAPED SERVO PROTECTOR/HOLDER/ ROBOT HOLDER MG013-5PCS/BAG

Material	2mm hard aluminum board
Surface Treatment	sand blasted and anodized
Dimension	35x30mm
Weight	10g
This holder is processed by CNC machine, error for hole site	±0.1mm, angle error

Specifications:, Application: suitable for Korean servo HS322、HS422, Towerpro MG995 , MG996、SG5010 servos, supporting Hitec、Parallax、Futaba、Towerpro servos with 35*30mm size., Kindly Remark:,

SDSHobby

RCEXL 3 CYLINDER IGNITIONS FOR NGK-CM-6-10MM 120 DEGREE (B-03 4.8V~8.4V 622A)

Specifications:, Working Voltage:, 4.8V-8.4V, Plug Type:, Futaba Female (for Battery), Futaba Female (for Tachometer), Net Weight (CDI):, 24g, Suitable for Spark Plug:, NGK-CM-6-10MM, Package Contents:,