RCModelScout.

HiModel

iCharger Multifunction battery 1-10S 10A 300W Balance Charger W/USB Port 1010B+

, , , , , , Specifications:, , , , , , , , , , , Specifications, , , , Input voltage range:, , , 10.0 -, , 18.0VDC, , Charge current range:, , , 0.05 -, , 10.0A, , Discharge current range:, , , 0.05 -, , 7.0A, , Maximum charge power capacity:, , , 300W @ input voltage > 13.5V, , Maximum discharge power capacity:, , , 30W, , Maximum extern discharge power capacity:, , 280W @ 40V/7A, , Current drain for balancing:, , , Balance accuracy:, , , , Lithium (LiPo/LiIo/LiFe) battery cell count:, , , , 1 -, , 10series, , , NiCd/NiMH battery cell count:, , , 1 - 25, series, , Pb battery cell count:, , , 1 -, , 18 series (2 - 36, V), , , Battery setup memories, ：, , , 10, , Intelligent temperature control:, , , Yes, , PC Connect:, , , USB port, , , Weight:, , , 410g, , Dimensions (L *W * D), :, , , , 143*97*26mm, 5.63”*3.82”*1.02”, , , External controls and connections, , , ,

Features:

●

High power,
high
current, high-performance power conversion circuit. The
iCharger
series uses advanced
Synchronous buck-boost DC/DC converter
technology with an output conversion efficiency that can reach over 90%. This not only saves power and reduces heat build up but also makes the charger more compact and conveniently mobile.
●

Two input power choices: DC jack with auto-resetting fuse (maximum input current 7A) and butt-welded alligator clips with 4mm bullet connectors (25A)
.
T
he output power
can be adjusted to align with the available
input power, thus prevent
ting

input current
overload and protecting the DC source
.

●

The
iCharger
series can be
u
sed with three types of Lithium batteries - LiPo, Lilo, LiFe - and has a fully integrated cell balancer.
●

Internal temperature sensor and temperature controlled automatic cooling FAN controls the internal temperature and provides intelligent protection. When the internal temperature is over 60
℃
(140
o
F
), the output power is automatically reduced by 25%. If the temperature exceeds 65
℃
(149
o
F
) the charge cycle is stopped.
●

Convenient set of 10 battery profile memories that can be saved and loaded by number.
●

2x16 backlit LCD screen that provides rich information including active mode, current, voltage, total charge (mAh), charging time and temperature etc.
●

Various charging/discharging settings and cycles to meet a wide range of customer needs. For Lithium batteries: balance charging, normal charging, fast charging, storage, discharging, ext-discharging, charge/discharge cycling, and battery monitoring. For NiCd/NiMH batteries: charging-auto, charging-manual, discharging, charge/discharge cycling and forming charge. For Pb batteries: charging and discharging.

●

Unique Lithium battery expanding discharge program. When you connect the external capacity resistance, you can use it as the maximum discharge power capacity—280W (@40V/7A).

●

Unique Lithium battery Monitor program.
When you use other equipment to charge or discharge a Lithium pack, you can use the
iCharger
to monitor the per-cell voltages, battery temperature and process time. If any individual cell appears over-charged or over-discharged or the pack is too hot or the process has gone on for too long, the
iCharger
will generate an alarm sound and the related information will blink.
●

Electric motor test mode can be used to run-in electric motors, test motor parameters and performance, check tolerances etc.
●

Foam-cut drive. In this mode, the charger acts as a convenient power supply for a hot wire foam cutter.
●

Battery
interior resistance measurement. The
iCharger
can not only measure the
internal
resistance of the battery pack, and also can measure the per-cell
internal
resistance (only available for lithium battery).
●

Perfect protection. The
iCharger
has protection for reversed polarity (input or output), low input voltage, battery temperature, charging capacity and time overrun.
●

Support
upgrading the hardware program by USB port. The
iCharger
also support the “Open Format” data of the “logview” software and can display, plot and analyze the charge and discharge data by it. (See detail information about
logview
in the
following website,
http://www.logview.info
)

Includes/Requires:

Includes:1 x charger
1 x Alligator Clips Cable
1 x pair alligator clips for lead-acid battery
1 x temperature sensor
1 x USB cable
1 x CD disk for instruction manual & software
* The balance charging board is not provided with the charger, to be purchased separately.

Found 11 years, 8 months ago