RCModelScout.

BevRC

Frsky TFR8SB- Compatible with Futaba FAAST radio with Sbus and RSSI port

:11.5g, :, 14ms (FS – Normal Speed Mode), Note: Be sure that when using battery or regulated output from ESC, the capacity must meet the usage conditions of servos., Use native failsafe position preset on the transmitter side:, If not disabling failsafe on the transmitter side, TFR8SB will use native failsafe position preset on the transmitter side., Set failsafe on TFR8SB side:, TFR8SB supports failsafe function for all channels. Follow the steps below to set failsafe on TFR8SB:, 1) Bind the receiver first, and disable failsafe on the transmitter side;, Note: HS mode is only applied for high-speed digital servos. Other servos should select FS mode, otherwise servos will get hot or even burn out., Note: Do not perform linking procedure while motor’s main wire is connected or engine is operating, otherwise damage may occur. After linking is completed, recycle the receiver power and check if the receiver is really under control by linked transmitter.,

It's a good choice for your multi-rotor with Naza or YS-X4 controller, supoort Sbus fucntion, less cables needed.

Also with  nearly the same range and fucntion as the stock Futaba R6208SB, but much cheaper price, surely it's a good choice for your second Rx for your futaba FASST radio.

1.  Introduction

1.1.1
Compatible systems

.

1.1.2
Compatible servos at SB port

Futaba S.BUS servos, FrSky S Bus compatible servos D12MB

Weight

Servo Frame Rate

7ms (HS – High Speed Mode)

1.3
Features

1) Compatible with FASST 2.4GHz Air Systems (7CH Mode/Multi Mode)

2) SB port is compatible with Futaba S.BUS servos and FrSky S Bus compatible servos

3) With RSSI output

4) Two selectable failsafe setting options (use native failsafe on radio side or set failsafe on TFR8SB side)

5)S.BUS servos/S Bus compatible servos channel setting channel setting on TFR8SB

6)Improve sensitivity and stability

7)Wider and higher operating temperature range, suitable for all kinds of models

8)Firmware upgradeable

2.  Set Up

2.1 Bind procedure

Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is

off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.

2.2 Setting failsafe

TFR8SB support two selectable failsafe setting options, either use native failsafe position preset on the transmitter side,

or set failsafe on TFR8SB.

2.2.1

2.2.2

2) Set all transmitter controls to the desired failsafe position;

3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is

set up successfully.

I f you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.

2.3LED status

RED LED

GREEN LED

Mode

Off

On

Normal mode

On

On

Waiting to be bound

Flashing

On

Signal lost

On

Flashing twice

Set failsafe

Flashing slowly

On

Normal speed mode

Flashing fast

On

High speed mode

3.  How to switch between two PPM modes

Turn the transmitter off, connect the battery to the receiver, press the F/S button of receiver for 6 seconds and then release. The red LED will flash fast in HS Mode and slow in FS Mode. Repeat this to alternate modes.

4.  Channel Setting Methods

Channel setting for Futaba S.BUS servos and FrSky S Bus compatible servos can be performed at TFR8SB.

1, Connect the SB port and RSSI port by the provided cable.

2, Connect an S.BUS servo or S Bus compatible servo to the output connector (1~8) corresponding to the channel you want to set.

Output Connector

Channel Setting

Mode A

Mode B

1

1

9

2

2

10

3

3

11

4

4

12

5

5

13

6

6

14

7

7

15

8

8

16

3, Connect battery to the receiver, RED blinking LED indicating the channel setting is completed in Mode A. To switch to Mode B, press the button on receiver for three seconds until GREEN LED starts to blink, indicating the channel setting is completed in Mode B.

Futaba is trade name and/or trademark of their respective companies and are not products of FrSky Electronic Co., Ltd.

Found 11 years, 9 months ago