HobbyWireless
TX-V1024 1000mW 2.4 GHz plug and play transmitter with wires - Lawmate
| Nominal output impedance | 50 ohms |
| Operating Voltage | 10.5 - 13 volts DC |
| 75-ohm impedance | 1Vp-p |
| 10k ohm impedance | 1Vp-p |
| Sub carrier frequency | 6.5MHz |
| Operation temperature | -10 to 40 degrees Celsius |
| Storage temperature | -40 to 80 degrees Celsius |
| Operating humidity | 20 to 80% |
| Weight | 40g (transmitter only) |
Details:, This is a plug and play transmitter only, part of our FPV1024 plug and play system., The plug and play board has lots of important features built-in such as:, - High quality microphone, Features:, , Specifications:, , Notes:, All transmitters shipped to any addresses within US territory will have only the Channel 1 (2410 MHz) available., Disclaimer:, Hobby Wireless is not responsable any damage, loss, illegal operation or changes made by the user to the transmitter will be totally the user's responsibility.,
This combo uses PLL (Phase-Locked Loop) technology to prevent frequency drift.
- Audio volume control
- High quality 5v voltage regulator (no heat and noise free)
- Reverse-Polarity Protection (avoids damage if you plug the battery pack inverted)
- Dual power output (provides selectable power for 5 and 12 volts cameras)
- Molex connector with safety latch (prevents connection to come loose while in use)
- Power LED (helps to identify bad power connection, reminds you to disconnect power when it’s not in use)
If you want to expand your current FPV1024 system to another R/C vehicle, or you have damaged your existing transmitter, or you either want to buy everything separated to build your own system, this is the deal.
What are the advantages of a plug-and-play transmitter?
A plug and play transmitter eliminates the use of the stock bulky and heavy connectors, no soldering is needed, with only two clicks you will have the camera, battery, microphone (built-in), reversed-polarity protection, microphone volume control...besides all that it can provides power to 5 V or 12 V cameras,
click here for plug and play cable for cameras.
It works with any of our 2.4 GHz receivers, that includes the
ORACLE diversity receiver
as well.
It uses PLL technology, very tiny and so light weight that if you hold it in one hand and a coin of the same size on the other hand, you'll have a hard time telling which one is heavier.
To those whom are going to use it, make sure the voltage your camera needs to be operated, and if you are building your own setup from scratch, the camera connector needs to be made using Futaba type connection, for the following wires colors (white video in) (red + positive) (black - negtive)
It is able to send audio and video wirelessly for more than 3 miles with high gain antennas
.
* HERE WE HAVE SOME SIMPLE TUTORIAL VIDEOS THAT MAY BE HELPFUL *
1000mW (1 Watt) RF output power Plug and PlayE
Eight (8) selectable channels
(USA version only channel 1 is available. It does not affect the performance of the transmitter)
2.4 GHz frequency band
Works with any camera PAL, NTSC and SECAM
Digital Phase-Lock-Loop circuit no drifting problem
Works with any of our receivers
Plug and Play camera cable is sold separated click here
Highly integrated circuit
High reliability/linearity/AIGaAs/GaAs FET amplifier module
Uses digital phase-lock-loop circuit without temperature drifting problem
Total weight 59 grams complete with antenna
Wires with Molex connectors are included
Consumption Current 450mAh
Video input voltage
Audio input voltage
If you are not going to run your RC model, do not turn this transmitter on and leave it on for several minutes, it can overheat damaging the unit!
It is 1000mW transmitter in a tiny metal box!!!
-
No license is required to purchase it, however i
n order to legally operate within USA an
amateur radio license
is required.
Check price and availability
Found 11 years, 9 months ago