Hobby-Lobby
ShockWave 36 RTR w/ T-Drive (OVERSIZE)
| Beam | 9 in. |
| Engine Size | .32 water-cooled Marine |
| Radio | 2 channels |
| Speed | 30 mph |
| Hull Material | Fiberglass |
| Hull Type | Deep-V |
| Trim Scheme Colors | White |
| Drive System | Flex shaft |
| Prop Size | 1.90 x 3.0 in |
| Exhaust | Tuned pipe |
Needed to complete: Fuel (quart), 500cc Fuel Bottle or Fast Tap Quart Bottle Spout, Glow Plug Wrench, 7.2v Battery and charger, Ni-Cd Glow Driver, 12 AA alkaline batteries (8 for the transmitter and 4 for the receiver), Clear tape to seal radio box Tech Notes: To increase speed on calm water, bend the trim tabs up 1/4 to 1/2 inch with a pair of pliers. This will lift the front of the hull out of the water at high speeds, lower hull resistance and increase speed. This may, however, lessen the cornering ability. The trim tabs can also be adjusted individually to level the boat and compensate for engine and propeller torque. You can also increase top speed by removing the anti-skid fins, but you may experience reduced stability in rough conditions. Technical Specifications: ShockWave 36 RTR w/T-Drive Specs:Length: 36 in., ,
The Shockwave 36 is a blazing fast Measuring over three feet in length, the Pro Boat® ShockWave® 36 is a ready-to-run deep-V speedster that can reach speeds in excess of 30 mph. The power comes from the installed Dynamite®.32 Marine Engine. The Dynamite.32 Marine is water-cooled and comes equipped with a convenient electric starter and high-performance tuned exhaust system. Control is provided by Pro Boat's trusty pistol-grip radio system that offers drivers analog adjustment of steering rates as well as throttle and steering trim.
The ShockWave's workmanship is equally impressive. The hull is professionally built from fiberglass and painted with the same technologies used in today's automotive finishes. Rubber motor mounts significantly reduce vibration and lengthen the hull's life. There are no plastic parts on this boat. All the running hardware is stainless steel and aluminum, including the adjustable trim tabs that let drivers adjust the "ride" for varying wave conditions. Anti-skid fins, an oversized rudder and an adjustable strut for the Pro Boat propeller add even more ride-tuning options. This is high-octane RC offshore excitement at its best. ShockWave 36 RTR w/T-Drive Highlights:
Water-cooled Dynamite®.32 marine with TigerDrive and electric starter
Completely ready-to-run
Stainless steel and aluminum running hardware
Pro Boat® propeller
Pre-painted fiberglass hull
Pro Boat® AM 27mHz pistol-grip radio system
Speeds over 35 mph
Needed to complete: Fuel (quart), 500cc Fuel Bottle or Fast Tap Quart Bottle Spout, Glow Plug Wrench, 7.2v Battery and charger, Ni-Cd Glow Driver, 12 AA alkaline batteries (8 for the transmitter and 4 for the receiver), Clear tape to seal radio box Tech Notes: To increase speed on calm water, bend the trim tabs up 1/4 to 1/2 inch with a pair of pliers. This will lift the front of the hull out of the water at high speeds, lower hull resistance and increase speed. This may, however, lessen the cornering ability. The trim tabs can also be adjusted individually to level the boat and compensate for engine and propeller torque. You can also increase top speed by removing the anti-skid fins, but you may experience reduced stability in rough conditions. Technical Specifications: ShockWave 36 RTR w/T-Drive Specs:
Length: 36 in.
Beam: 9 in.
Engine Size: .32 water-cooled Marine
Radio: 2 channels
Speed: 30 mph
Hull Material: Fiberglass
Hull Type: Deep-V
Trim Scheme Colors: White
Drive System: Flex shaft
Prop Size: 1.90 x 3.0 in
Exhaust: Tuned pipe
Check price and availability
Found 11 years, 9 months ago