ngHobbies
Single BL-Ctrl V3.0 2XL
| IMPORTANT | Use FlightCtrl Firmware V2.02 (or greater), otherwise read the instructions in the wiki ! |
| •voltage | 10 to 30V -> 3 -7S Lipo |
| • current | up to 60A with appropriate cooling |
| • Silent Start | test tone at startup can be disabled |
| • hole | 3mm |
| • Dimensions (W x H ) | approx 75mm x 26mm (without capacitors) |
| • Dimensions (W x H ) | approx 96mm x 26mm ( with capacitors) |
| • weight | 15g (with capacitors) |
Note: The BL-Ctrl 3.0 controller is specifically designed and optimized for our motors. For maximum stability of the MikroKopter setpoints are set almost instantaneously on the motor. If other motors (especially larger power classes) are used with this controller, this fast change of setpoints can easily lead to very high peak currents, which bring the BL-Ctrl control to the limit or an overload. This is no fault of BL-Ctrl3.0 controller, but a systemic property., This new version has the following features:, Dimensions:, The following items are included in this kit:,
Extremely fast brushless controller version V3 for any MikroKopter with Firmware V2.02 or higher.
The board is tested and programmed (including bootloader)
The board is already 98% finished, manufactured with SMD technology. Some soldering is required to finish the board.
The BL-Ctrl kit is pre-tested and approved to be used with the Navi-Ctrl, Flight-Ctrl, MK3MAG, BL-Ctrl.
• 6 -layer PCB for optimal heat dissipation . 70u copper layers make the entire circuit board to the heat sink .
• current limiting and temperature limiting
• Active freewheeling -> less power loss
• rapid acceleration and braking of the propeller. Active and seamless braking gives the speed precisely and quickly on the new setpoint .
• return energy to the lipo when braking. Seamless transition from acceleration to braking
• significantly faster control with speed control
•
Video
Other Features
• Adjustable motor timing in several steps of 13-28° - compatible with the most common BL motors
• Adjustable switching frequency ( 10kHz - 20kHz )
• PPM to 500 Hz with simultaneous I2C - bus operation for telemetry and data logging
• Integrated 12V stabilization for LED lighting and other 12V appliances
• Switchable outputs for lighting -> ZB The blinking lights at low voltage
• Software adjustable direction of rotation
• Adjustable current and temperature limits
• Adjustable start-PWM
Interface
• various interfaces for setpoint input ( I2C, PPM ( 500Hz ) , serial)
• Integrated current measurement measurement of the actual current and the used capacity on the Mikrokopter control
• voltage and temperature measurement with data transmission to the ground station and data logging
• 11-bit resolution (2048 steps )
• various feedback to the MikroKopter-FlightCtrl ( blocked motor , power limiting , etc. )
• extented configuration options (eg current limit , temperature limit , ...)
• two LEDs (OK and Error )
• Addressing by jumper ( address 1-8 )
• I2C bus access possible in PPM mode - for data logging and telemetry in PPM mode
• status messages are transmitted to the FC ( engine blocks , Current, Self-test error ...)
• current measurement up to 75A per controller
• Convenient configuration of the BL controller via FC
1 x BL-Ctrl V3 SMD preprogrammed board.
2 x Low ESR 35V capacitor.
The electronic components must be protected from moisture and humidity. When operating under such special conditions a corresponding (removable) protective coating must be used
This is sold as it is for private, non-commercial use.
Please read the Terms and conditions of the software regarding commercial use.
For warranty info click here
More information on Wiki
Check price and availability
Found 10 years, 8 months ago