Estes Engines RCPlanet Page 28 Review

RCPlanet

HPI ENGINE MOUNT SAVAGE X HPI86079

, , Length:, 2.9" (74mm), Width:, 0.27" (7mm), Height:, 0.27" (7mm), , ,

HPI Racing engine mount braces for the Savage X is ...

RCPlanet

HPI K4.6 HIGH OUTPUT HELLFIRE ENGINE HPI15204

, ,

HPI K4.6 High Output Pull Start Engine for the HPI ...

RCPlanet

HPI K4.6 .28 NITRO STAR ENGINE WPULL START HPI15201

, Crankcase:, 3.29" (83.5mm) (from rear of case to front without shaft), Height:, 4.40" (111mm) (from bottom of case to the top of the head), Width:, 1.81" (mount flange), Mount Holes:, 1.42" (measured from center to center width), Mount Holes:, .82" (Between holes front and back), RPM:, Max 39,000 RPM, Horsepower:, 2.9 @ 35,000 RPM, Crankshaft diameter:, 5mm (clutch bell area), Crankshaft diameter:, 6.7mm (threaded portion), Crankshaft screw:, 3 x 12mm caphead screw, Capacity:, 4.60cc (.28 ci), ,

HPI Racing's new Nitro Star K4.6 engine packs a serious ...

RCPlanet

HPI NITRO STAR T3.0 ENGINE HPI15107

, Height from crankcase bottom to top of cylinder head:, 3.8" (96mm), Width including mounting tabs:, 1.57" (40mm), Width below mounting tabs:, 1.2" (31mm), Width between mounting holes same side:, 0.43" (11mm), Width between mounting holes opposite side:, 1.2" (31mm), Width of exhaust opening:, 0.87" (22mm), Height of exhaust opening:, 0.17" (4.2mm), Distance between muffler mounting holes:, 1.1" (28mm), Crankshaft Thread Size:, 1/4-28, Bore x Stroke:, 16.8 x 13.6mm, Displacement:, 0.18 cu in (3.01cc), Maximum Power:, 2.2PS/31,000 RPM, ,

HPI Nitro Star T3.0 Engine for use with the RTR ...

RCPlanet

HPI NITRO STAR T-15L ENGINE PULLSTART HPI15180

, Displacement:, 0.15 cu in (2.49cc), Bore and Stroke:, 15.0 x 13.6mm, Maximum Power:, 1.2hp/29,000 RPM, Height from Crankcase Bottom/top of Cylinder Head:, 3.9" (98.7mm), Distance/Mounting Tab to Exhaust Mounting Hole Center:, 1.4" (36.2mm), Distance/Starter to Front Bearing:, 2.7" (70.1mm), Mounting Hole Centers Opposite Side:, 1.2" (31mm), Mounting Hole Centers Same Side:, 0.43" (11mm), Width at Mounting Tabs:, 1.6" (40mm), Front Mounting Hole Center to Front Bearing:, 1.2" (29.5mm), Center of Carburetor to Center of Crankshaft:, 0.97" (24.7mm), Cylinder Head Diameter:, 1.9" (49mm), Crankshaft Size:, UNF 1/4-28, Carburetor Settings, High Speed Needle:, Flush with carb body, Low Speed Needle:, Flush with carb body, turn needle in 1/8 turn increments to adjust-no more than two turns from flush, Idle Adjustment Screw:, Set so that clutch does not engage, turn counter clockwise to reduce idle speed, clockwise to increase it, Note:, High and low speed needles are factory set and not recommended to be changed., ,

HPI Racing Nitro Star T-15L Engine With Pullstart. Genuine HPI ...