Flying-Hobby
GLOW PLUG-4A
| Specification | ●#4A glow plug x1 |
Instructions:, ●Glow plug with Medium heat rating, suitable for mild climate or high speed engine., NOTE:, ● Carbon buildup on glow plug element may occur as the glow plug age. The dark brown carbon buildup will result in reduced ignition point, causing difficulties in starting as well as rough running. The glow plug should be replaced when this occurs., 1. Too cold: Poor throttle response at low engine speed; Unsustainable Idle causing the engine to stall; Slow engine acceleration; The engine cools quickly during Idle., 2. Too hot: After running the engine at high speed, the rotation speed decreases slowly when throttle down the engine. Engine has difficulties returning to idle speed quickly. The glow plug is burnt at higher engine temperatures.,
●Apply to R/C Helicopter engines、R/C Airplane engines and R/C Car ...Flying-Hobby
90 HIGH PERFORMANCE MUFFLER ( BLACK)
| ●Size | Φ49.1 x 318 x 81.75mm |
| ●Weight | 225g |
| Accessories | ●Muffler x1 |
Instructions:, ●Apply to 90 size helicopters, according to the strength character of 90 engine to design, features much increase the horsepower, fuel-saving, low noise, and the highest air exhaust volume on the market., ●Great design and test to three spaces: expansion chamber, accelerated section, silencer chamber, high efficiency and the quick respond of medium speed and high speed, great for 3D flying., Specification:,
●Use for O.S 91SR/HZ & ALIGN 91H/HP engine. ●Muffler Spacer ...Flying-Hobby
50 HIGH PERFORMANCE MUFFLER ( BLACK)
| ●Size | Φ41.2 x 270 x 70.5mm |
| ●Weight | 147g |
| Accessories | ●Muffler Spacer x1 |
Instructions:, ●Apply to 50 size helicopters, according to the strength character of 50 engine to design, features the highest air exhaust volume on the market., ●Great design and test to three spaces: expansion chamber, accelerated section, silencer chamber, high efficiency and the quick respond of medium speed and high speed, great for 3D flying., Specification:,
●Suitable for 50H,55H engine. ●Muffler x1 ●Pressure nipple x1 ●Pressure ...Flying-Hobby
THUNDER TIGER ZERO X II HEADSPEED GOVERNOR
| Model | Zero X II |
| Control | Digital advanced control |
| Speed pick-up | Direct detection of engine rotation |
| RPM resolution | 0.0003HZ |
| Control response | 14ms |
| Range | 10,500~21,000rpm |
| Operating voltage | DC 4.8~8.4V |
| Current drain | 40mA (4.8V) |
Item Description:, The Zero X II is a state-of-the-art digital engine speed governor for model helicopters., Speed stability accuracy: 1%,
It monitors engine speed automatically and maintains constant RPM by ...Flying-Hobby
THUNDER TIGER RED LINE RL-53H
| Content | RL-53 engine x 1 EA |
Flying-Hobby
91H CYLINDER LINER
| Specification | ●Cylinder liner x1 |
Instructions:, ●Use for ALIGN 91H/91HP engine.,
Flying-Hobby
ALUMINUM HEXAGONAL BOLT
| ●Weight | 5.8g |
Instruction:, ●6061-T6 Aluminum alloy material and CNC processed。, ●Use with:, Metal Engine Bearing Block Set (, Specification:, ●Aluminum hexagonal bolt x 2(Φ5.5x54mm),
HN6105 ) 600PRO Receiver Mount ( H60201 ) Tail Boom ...Flying-Hobby
600D CARBON FIBER BLADES
| ●Shape | Symmetrical wing |
| ●Length | 600x55x7.5mm |
| ●Width | 12mm |
| ●Shaft Diameter | 4mm |
| ●Weight | 230g/set |
Instruction:, ●Use for T-REX 600/600CF/50 Engine Helicopter, Specification:,
Flying-Hobby
600N PAINTED CANOPY
Instruction:, ●Apply to 600 Nitro (Engine Helicopter), Specification:, ●GF Painted canopy x 1,
●Canopy nut x 2 ●Canopy clip x 1 ●Socket button ...Flying-Hobby
CRANKSHAFT LOCKING TOOL: 30-90 HELIS - BLACK
Features:, Made of durable engineering plastic, it locks the crankshaft without risk of damage to any part of the engine., Requires:, Removing coverplate or pull starter from the rear of the engine., Instructions:, Remove the crankcase rear coverplate from the engine and rotate the crankshaft to the bottom-dead-center position. Insert the crankshaft clamp so that its grooved portion surrounds the crankpin and lower end of the connecting-rod, and securely tighten the flywheel, fan or pilot shaft onto the crankshaft. Remove crankshaft clamp when completed and re-install the coverplate back onto the engine.,
This device facilitates the installation or removal of a flywheel, ...Flying-Hobby
91H CONNECTING ROD
| Specification | ●Connecting rod x1 |
Instructions:, ●Use for ALIGN 91H/91HP engine.,
Flying-Hobby
SLITE SELECTED PROFESSIONAL TOOL 3PCS
Attention:, The peak is hard and sharp, please keep it well don't use it exceed the use range, Feature:, A range of high quality stainless steel tweezers, designed to meet the requirments of the electronics and precision engineering industries, Materials:, Super Hard, Included:, ST-12ESD x 1,
Product description Fine Super Tweezer ANTI-MAGNETIC ANTI-ACID STEEL ST-13ESD x ...Flying-Hobby
CRANKSHAFT LOCKING TOOL: 30-90 HELIS - YELLOW
Features:, Made of durable engineering plastic, it locks the crankshaft without risk of damage to any part of the engine., Requires:, Removing coverplate or pull starter from the rear of the engine., Instructions:, Remove the crankcase rear coverplate from the engine and rotate the crankshaft to the bottom-dead-center position. Insert the crankshaft clamp so that its grooved portion surrounds the crankpin and lower end of the connecting-rod, and securely tighten the flywheel, fan or pilot shaft onto the crankshaft. Remove crankshaft clamp when completed and re-install the coverplate back onto the engine.,
This device facilitates the installation or removal of a flywheel, ...Flying-Hobby
CRANKSHAFT LOCKING TOOL: 30-90 HELIS - WHITE
Features:, Made of durable engineering plastic, it locks the crankshaft without risk of damage to any part of the engine., Requires:, Removing coverplate or pull starter from the rear of the engine., Instructions:, Remove the crankcase rear coverplate from the engine and rotate the crankshaft to the bottom-dead-center position. Insert the crankshaft clamp so that its grooved portion surrounds the crankpin and lower end of the connecting-rod, and securely tighten the flywheel, fan or pilot shaft onto the crankshaft. Remove crankshaft clamp when completed and re-install the coverplate back onto the engine.,
This device facilitates the installation or removal of a flywheel, ...