DPCAV
GFORCE SENSOR, LOW G
Force sensor is factory calibrated to measure up ..." />
| Resolution | approx. 0.05 G in each axis |
| Maximum | ±7 G in each axis |
| Power input (Standalone Mode) | 4V to 16V |
| Weight | approximately 4 grams (0.15 oz) |
| Dimensions | approximately 28x16x10 mm (1.1x0.62x0.4 Inch) |
| GFORCE-LOW Instruction Manual | Click Me! |
Specifications and Features:, ,
This tiny G-Force sensor is factory calibrated to measure up ...DPCAV
ELOGGER VIDEO OSD-PRO EXPANDER MODULE
| Video Compatibility | NTSC / PAL. |
| Power | Provided by eLogger V3 (sold separately). |
| Video I/O | Two 3-Pin headers. |
| Audio I/O | Two 3-Pin headers. |
| Size | 2.4 x 1.0 inches (61 x 25 mm). |
| Weight | 0.5 ounces (13.5 grams). |
| Instruction Manual | Click Me! |
| Eagle Tree Web Site | Click Me! |
The OSD Pro is a powerful, modular, and fully configurable video/audio On-Screen Display (OSD) device. It provides graphics and voice announcements that report a variety of alarms and data, including: acoustic variometer, electrical performance, Home Arrow, Return to Home, Failsafe, “RADAR”, waypoints, and many other features., how YOU configure the display. Here's a screen shot that shows some of the information that can be shown:, , All the data parameters that are supported by the eLogger can be displayed on the video display. Here are some examples:, , Specification Summary:, IMPORTANT NOTE: The OSD-Pro requires the EagleTree eLogger V3 or V4 module. To display navigation related data the GPS expander module is needed. These items are available separately (please see the related items links shown near the bottom of the page).,
The Eagle Tree Video OSD Pro Expander module adds graphical ...DPCAV
GUARDIAN 2D/3D INERTIAL STABILIZER (STANDALONE MODEL)
| Instruction Manual | Click Me! |
| PC Software | Click Me! |
Q: Why do I need the Guardian?, The Guardian helps both beginner and expert pilots fly with confidence, and provides two key modes of operation: In 2D flight mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot easier to adjust and fly your plane. The Guardian "remembers" level flight for your model and returns it to level flight when needed, as well as providing precise "fly by wire" control., The Guardian has two submodes for 3D flying: In 3D Heading Lock submode, simply center your sticks to have the Guardian lock onto your present attitude (pitch, roll, and heading), which can make it easier to perform stunts like prop hanging, inverted flight, knife edges, low speed harriers, etc. In 3D Gyro submode, the Guardian uses its built-in 3 axis gyro to increase your model’s stability, while leaving you in full control. In this mode the Guardian greatly reduces the effects of gusts, turbulence, motor torque and other factors, and can expand the maneuverability of your model in a variety of conditions., Q: I Fly FPV. Is the Guardian for me?, Q: Will the Guardian work with my model?, Q: How do I install the Guardian?, Q: How do I configure the Guardian?, Q: How does the Guardian work?, Q: What sets the Guardian apart from other Stabilization systems out there?, *Note: Using the PC software will require a common Micro-USB cable. Most likely you already have one of these, but it not then they are available from your local electronic/computer store.,
Based on Eagle Tree's proven inertial stabilization technology, the Guardian ...DPCAV
5VDC/6VDC VOLTAGE REGULATOR (BEC), SWITCH-MODE TYPE
| Red | +5VDC |
| Black | Ground |
| Specifications | Input |
| Output | 5VDC/6VDC (jumper select), 3A maximum |
| Output Ripple | <50mV at 2A/12V |
| Technology | Switch-Mode Regulator (BEC/UBEC) |
| Size | 2.0 x 0.7 x 0.3 inch (51x17x9mm) |
| Weight | 12 grams |
| Origin | Made in China by HobbyWing Techonology Co. |
The DC input has 3-inch bare leads (Red wire = BAT+). The 5-inch long output cable has a 2-wire (3-pin) servo style connector, wired as follows:, ,
This Voltage Regulator accepts 6-26 VDC on its input and ...