SDSHobby
DYNAM BRUSHLESS ESC-30A FOR MODEL AIRPLANES
| Cont. Current | 30A |
| Burst Current (>10s) | 40A |
| BEC Model | switch |
| BEC Output | 5V/3A |
| Cells of Li-Po/Li-ion | 2S-4S |
| Cells of Ni-Cd/Ni-MH | 5S-12S |
| User Programmable | yes |
| Weight | 25g |
| L*W*H (Size) | 45*24*11mm |
| Balance Discharger Protection | N/A |
Specifications:, , Features:, Programmable Items:, Ø, Brake Setting:, Enabled / Disabled, default is disabled, Battery Type:, Li-xx (Li-ion or Li-poly) / Ni-xx (Ni-MH or NiCd), default is Li-xx., :, Soft Cut-Off (Gradually reduce the output power) or Cut-Off (Immediately stop the output power). Default is Soft Cut-Off., :, Low / Medium / High, default is Medium., For lithium batteries, the number of battery cells is calculated automatically. Low / medium / high cutoff voltage for each cell is: 2.6V/2.85V/3.1V. For example: For a 3 cells lithium pack, when “Medium” cutoff threshold is set, the cut-off voltage will be: 2.85*3=8.55V., For nickel batteries, low / medium / high cutoff voltages are 0%/45%/60% of the startup voltage (i.e. the initial voltage of battery pack), and 0% means the low voltage cut-off function is disabled. For example: For a 10 cells Ni-MH battery, fully charged voltage is 1.44*10=14.4V, when “Medium” cut-off threshold is set, the cut-off voltage will be: 14.4*45%=6.5V., When using balance discharge monitoring and protection function(i.e. Plugging the balance charge connector on battery pack into the BDMP socket on the Guard series ESC, the ESC monitors not only the voltage of the whole battery pack but also the voltage of each cell). For lithium battery, low / medium / high cut off voltage for each cell is: 2.6V/2.85V/3.1V. When the voltage of any cell in battery pack is lower than the cut-off threshold, the protection function activated., Startup Mode:, Normal / Soft /Super-Soft, default is Normal., Timing:, Low / Medium / High, default is Low. (Note2), Note2:, After changing the timing setting, please test your RC model on ground prior to flight!,
Net Speed controllers for brushless motors are designed for best ...SDSHobby
DYNAM BRUSHLESS ESC-25A FOR MODEL AIRPLANES
| Cont. Current | 25A |
| Burst Current (>10s) | 35A |
| BEC Model | switch |
| BEC Output | 5V/3A |
| Cells of Li-Po/Li-ion | 2S-4S |
| Cells of Ni-Cd/Ni-MH | 5S-12S |
| User Programmable | yes |
| Weight | 22g |
| L*W*H (Size) | 45*24*11mm |
| Balance Discharger Protection | N/A |
Specifications:, Features:, Programmable Items:, Ø, Brake Setting:, Enabled / Disabled, default is disabled, Battery Type:, Li-xx (Li-ion or Li-poly) / Ni-xx (Ni-MH or NiCd), default is Li-xx., :, Soft Cut-Off (Gradually reduce the output power) or Cut-Off (Immediately stop the output power). Default is Soft Cut-Off., :, Low / Medium / High, default is Medium., For lithium batteries, the number of battery cells is calculated automatically. Low / medium / high cutoff voltage for each cell is: 2.6V/2.85V/3.1V. For example: For a 3 cells lithium pack, when “Medium” cutoff threshold is set, the cut-off voltage will be: 2.85*3=8.55V., For nickel batteries, low / medium / high cutoff voltages are 0%/45%/60% of the startup voltage (i.e. the initial voltage of battery pack), and 0% means the low voltage cut-off function is disabled. For example: For a 10 cells Ni-MH battery, fully charged voltage is 1.44*10=14.4V, when “Medium” cut-off threshold is set, the cut-off voltage will be: 14.4*45%=6.5V., When using balance discharge monitoring and protection function(i.e. Plugging the balance charge connector on battery pack into the BDMP socket on the Guard series ESC, the ESC monitors not only the voltage of the whole battery pack but also the voltage of each cell). For lithium battery, low / medium / high cut off voltage for each cell is: 2.6V/2.85V/3.1V. When the voltage of any cell in battery pack is lower than the cut-off threshold, the protection function activated., Startup Mode:, Normal / Soft /Super-Soft, default is Normal., Timing:, Low / Medium / High, default is Low. (Note2), Note2:, After changing the timing setting, please test your RC model on ground prior to flight!,
Net Speed controllers for brushless motors are designed for best ...SDSHobby
ERC LCD 3CH 2.4GHZ GUN TRANSMITTER FOR RC MODEL BOAT AND CAR
Technical Parameters:, Frequency Band:, .400-2.483GHz, Transmission Speed:, 50kbps, Response Time:, 5.6ms, Frequency Interval:, MHz, Channel:, 3 CH, Sensitivity:, -90DBM, Transmission Range:, 150M, Modulation:, digital GFSK, Working Voltage:, 4-6V, Output Power:, 10MW, Input Signal:, PPM, Operating Current:, ≤, Antenna Gain:, 3db, Component:, Features:, precision Numerical control mode replaces the traditional PPM to eliminate radio interference and glitches, which troubled model hobbyists for years. So you can play 50pcs 2.4GHz at the same time without worry about disturbing. It’s control distance: 150—200M.,
50MA Transmitter with Module Box Receiver Box Power Switch TX ...SDSHobby
BOSCAM HD19 AERIAL PHOTOGRAPHY FPV MINI CAMERA (HIGH DEFINITION)
| Photos | JPEG (Format) |
| Multifunction interface | AV out, USB(Compatible with standard MINI 5Pin USB plug), DC input |
| 9. Dimensions | 37x37x31mm (Do not contain lens and prominent part) |
| 11. Operation temperature | -10~60 Celsius Degree |
Specifications:, 1. Image Sensor:, 1/2.5 CMOS, . Effective Pixels:, 5.0 Mega Pixels, 3. Lenses:, fixed focus, f=3.35mm, angle of view=142 degree, 4. Exposure Control:, Auto Exposure, 5. White balance:, Auto White Balance, Pixels:, 592×1944, Single continuous shooting:, Take 3/5/10 photos per one shooting, Auto continuous shooting:, Take one photo every other 3/5/10/30/60S, Video:, H.264 video compression (Format), Size :, 16:9 1920x1080, 4:3 1440x1080, 16:9 1280x720, 16:9 1280x720, Video section:, (, Quality/ Bit rate:, (, 7. Memory:, High speed Micro SD card (TF card) up to 32GB, Audio channel:, Mono, Lens wire to PCB board interface:, 5pin-1.25 (12V input, Ground, Video output, Audio output, Control input), 10. Weight:, 60g (not including memory card), 12. Built-in battery:, 3.7V/1000mA Rechargeable Li-ion battery, 13. Power input:, DC 12V/0.5A, Package Contents:,
6. Recording System n n n n n n ( ...SDSHobby
BOSCAM RC701 ALL-IN-ONE MONITOR + FPV WIRELESS RECEIVERS + DIVERSITY
| Screen size | 7inch |
| Screen type | TFT LCD screen/long life, LED backlight |
| Resolution | 800*480 |
| Brightness | 450cd/sq.m |
| Contrast | 500 |
| View angle | 140/120degree(Horizontal/Vertical) |
| Working Voltage | DV 7-12V(center positive) or 11.1V 3s lipo battery |
| Power consumption | < 8W |
| Size | 180*120*23mm |
| Working Temp | -10 ~ +65 degrees |
| CH1 | 5705MHz |
| CH2 | 5685MHz |
| CH3 | 5665MHz |
| CH4 | 5645MHz |
| CH5 | 5885MHz |
| CH6 | 5905MHz |
| CH7 | 5925MHz |
| CH8 | 5945MHz |
Specifications:, Features:, Built-in Dual Receiver with DIVERSITY Feature to retrive best video signal, Frequency of 8 Channels:, Package Contents:, AV Cable*1pcs,
Built-in 5.8G Dual diversity receiver automatically for best reception Built-in ...SDSHobby
2.4G IDEAL FLY APOLLO FPV QUADCOPTER RTF (RED COLOR) WITH 1080P CAMERA, GPS, LEFT HAND THROTTLE
| http | //bbs.5imx.com/bbs/forum.php?mod=viewthread&tid=778800&extra=&page=1 |
Parameters for Quadcopter:, Power Consumption (Flight Control Board):, 3.12W, Flight Weight:, <1200g, Hovering Precision (GPS Mode):, ±, Max. Speed of Tail Servo Horn:, 300 degree/sec, MAX. Tilt Angle:, 45 Degree, Max. Vertical Speed:, ±, Max. Flying Speed:, 5m/s, Axle Base:, 350mm, Working Temperature:, -10 to -50 Celsius Degree, Parameter for Radio Control:, , Frequency:, , Channel for Receiver:, , Control Distance:, 300 meters (outside or without obstruct), Receiving Sensitivity (1%PER):, >-93dBm, Transmitter Power:, <20dBm, Working Capacity:, 52Ma@6V, Battery:, 4pcs*AA, Parameter for Charger:, , Input Voltage:, 100-240V, Charging Current:, 1A/2A, Balance Current:, 00Ma, Power:, , Package Lists:, Features:, Pre-installation position makes the Gimbal conveniently mount on the bottom and also easily adjust the motions: moving up and down, rolling left and right, Flight Video:, Kindly Remark:, We provide the following colors and equipments for users; please carefully confirm the item No. and colors when you decide to purchase., IFLY-APRL:, , IFLY-APRR:, , IFLY-APBL:, , IFLY-APBR:, , IFLY-APWL:, White Color, IFLY-APWR:, White Color,
0.8m (Vertical), ±.5m (Horizontal) 4m/s .4GHz ISM 6CH 0W 1*Apollo ...SDSHobby
2.4G IDEAL FLY APOLLO FPV QUADCOPTER RTF (WITHOUT CAMERA), GPS
| Power Consumption (Flight Control Board) | 3.12W |
| Flight Weight | <1200g |
| Hovering Precision (GPS Mode) | ±0.8m (Vertical), ±2.5m (Horizontal) |
| Max. Speed of Tail Servo Horn | 300 degree/sec |
| MAX. Tilt Angle | 45 Degree |
| Max. Vertical Speed | ±4m/s |
| Max. Flying Speed | 5m/s |
| Axle Base | 350mm |
| Working Temperature | -10 to -50 Celsius Degree |
| Frequency | 2.4GHz ISM |
| Channel for Receiver | 6CH |
| Control Distance | 300 meters (outside or without obstruct) |
| Receiving Sensitivity (1%PER) | >-93dBm |
| Transmitter Power | <20dBm |
| Working Capacity | 52Ma@6V |
| Input Voltage | 100-240V |
| Charging Current | 1A/2A |
| Balance Current | 200Ma |
| Power | 20W |
| http | //bbs.5imx.com/bbs/forum.php?mod=viewthread&tid=778800&extra=&page=1 |
Parameters for Quadcopter:, Parameter for Radio Control:, Parameter for Charger:, Package Lists:, 1*Apollo Quadcopter RTF, Features:, Engineering plastic and titanium alloy filled in the case, Pre-installation position makes the Gimbal conveniently mount on the bottom and also easily adjust the motions: moving up and down, rolling left and right, Flight Video:,
Without battery 1*6CH Transmitter & Receiver 1* Landing Skid (one ...SDSHobby
NEW UPGRADED 1W FLEXIBLE FOLDABLE SOLAR CELLS/SOLAR PANEL 2V 500MA FOR DIY, PHONE CHARGER
| Maximum power (Pmax) | 1.0 W |
| Operating voltage (Vmp) | 1.5 V |
Electrical Performance Parameters:, Operating Current (lmp):, 500mA, Short-circuit current (Isc):, 600mA, Open circuit voltage (Voc):, .0 V, Weight:, 9g, Dimension:, 186mm* 78mm* 0.5mm, Features:, Application Notes:, 1. The product can be solar energy directly into electricity., 5. Ambient temperature:, -40 to +80 degree,
±g 1W flexible solar cells of amorphous silicon can foldable ...SDSHobby
DYNAM UBEC 5A (SWITCH-MODE) FOR RECEIVER, GYRO, SERVO
| Output Voltage | 5V@5A or 6V@5A (Selectable by using a jumper connector) |
| Output Current | Continuous 5A, burst 7.5A |
| Input | 7V-30V (2-6S Lipo battery) |
| Size | 48mm*27mm*10mm (L*W*H) |
| Weight | 30g |
Features:, The 5A-HV-UBEC is a switch-mode DC-DC regulator works with 2S to 6S Lipo battery, and outputs a consistent safe power supply for your receiver, gyro and servos., Specification:, Features:, Uses advanced switch mode DC-DC regulator IC.,
It is very suitable for large scale electric powered RC ...SDSHobby
2013 NEW FPV 5.8G 600MW A/V TRANSMITTING/RECEIVING SYSTEM COMBO TS832 + RC832 32 CHANNEL WIRELESS AUDIO/VIDEO SYSTEM
| 1. 32 Channels | covering A, B, E bands and F band (airwave band), four bands and all frequency compatible. |
| 4. Light weight | 85g transmitter, 22g receiver |
| - RX/TX | RP-SAM jack |
| - Antenna | RP-SMA plug |
| - Transmission Frequency | 5.8 G |
| - Transmission Power | 600 mw |
| - Transmission Frequency Point | 32 points |
| - Input Voltage | 7-16V |
| - Antenna Connector | launch module end RP-SMA, antenna jack end RP - SMA plug |
| - Work Current | 220 mA / 12V |
| - Working Temperature | - 10 to 85 Celsius Degree |
| - Automatic Video Formats | NTSC/PAL |
| - Audio Bandwidth | 6.5M |
| - Net Weight | 22g |
| - Dimension | 54 * 32 * 10 mm |
| - Operating Frequency | 5.8 GHz |
| - Launch Frequency Point | 32 points |
| - Input Voltage | 12V |
| - Max Working Current | 200 mA |
| - Antenna Impedance | 50 ohm |
| - Antenna Connector | receiving and sending module end RP - SMA antenna jack end RP - SMA plug |
| - Video Impedance | 75ohm |
| - Automatic Video Formats | NTSC/PAL |
| - Dimension | 80 * 65 * 15 mm |
| - Receive Net Weight | 85 g |
Features:, Description:, Transmitter TS832 Parameters:, - Video Bandwidth: 8M, Receiver RC832 Parameters:, The Channels and Frequency Adjustment for Reference:, , Package included:, - 1 x RC832 Receiver,
. Convenient operation surface with double digital display screen and ...SDSHobby
2013 NEW FPV 5.8G 600MW A/V TRANSMITTING TX SYSTEM TS832 32CH WIRELESS AUDIO/VIDEO SYSTEM
Description:, - RX/TX:, , - Antenna:, , Transmitter TS832 Parameters:, - Transmission Frequency:, 5.8 G, - Transmission Power:, 600 mw, - Transmission Frequency Point:, 32 points, - Input Voltage:, 7-16V, - Antenna Connector:, launch module end RP-SMA, antenna jack end RP - SMA plug, - Work Current:, 20 mA / 12V, - Working Temperature:, - 10 to 85 Celsius Degree, - Automatic Video Formats:, NTSC/PAL, - Video Bandwidth:, 8M, - Audio Bandwidth:, 6.5M, - Net Weight:, 2g, - Dimension:, 54 * 32 * 10 mm, The Channels and Frequency Adjustment for Reference:, , Package included:, 1 x TS832 Transmitter,
RP-SAM jack RP-SMA plug - 2 db antenna gain 1 ...SDSHobby
IMAX B6AC 1-6S MULTIFUNCTIONAL PROFESSIONAL BALANCE CHARGER/DISCHARGER WITH BUILT-IN AC ADAPTOR AND OUTPUT 1A / 5W
| Operating Voltage Range | AC 100-240V; DC 11-18V |
| Charging Current Range | 0.1-5.0A |
| Discharging Current Range | 0.1-1.0A |
| Max. Input/Charging Power | 50W |
| Lithium Battery | 1-6S |
| Ni-Cd/Ni-MH Battery | 1-15S |
| Lead Battery Voltage | 2-20V |
| Dimension | 135 * 144 * 36mm |
| Available Plugs | USA, Euro and Australia |
Introduction:, This item is for a rapid charger/discharger for all kind of battery of RC hobby, with built in balancer for lipo battery. Battery that can be charged by this charger,Lipo / Li-ion / LiFe / NiMh / NiCad / Pb / Lead Acid, Specification:, Ma. Discharging Power: 5W, Features:, Optimized operating software, Delta-peak sensitivity: The automatic charge termination program based on the principle of the Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process will be terminated automatically., Processing time limit:, You can also limit the maximum process time to avoid any possible defect., Accessories Included:,
B6AC features the so-called AUTO function that set the feeding ...SDSHobby
SKYRC 6X80+ MULTIFUNCTIONAL INTELLIGENT CHARGER/ BLANCE CHARGER WITH OUTPUT 5A/ 8W-BLUETOOTH VERSION
| DC Input | 11-18V |
| Charge circuit power | AC Input 50W, DC Input 80W |
| Charge current range | 0.1-10.0A |
| Discharge current range | 0.1-5.0A |
| Current drain for balancing port | 200mA/cell |
| LiPo/LiFe/Lilon cell count | 1-6Cells |
| Pb battery voltage | 2-20V |
| Net weight | 525g |
| Dimension | 135x112x60.9mm |
Specifications:, AC Input:, 100-240V, Discharge current power: 8W, NiCd/NiMH battery cell count:, 1-15Cells, Features:, l, Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge termination program based on the principle of the Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process will be terminated automatically., Package Details:,
With bluetooth, you can wireless control the charger through smartphone ...SDSHobby
2.4G IDEAL FLY APOLLO FPV QUADCOPTER RTF WITH 1280P CAMERA, GPS
| Power Consumption (Flight Control Board) | 3.12W |
| Flight Weight | <1200g |
| Hovering Precision (GPS Mode) | ±0.8m (Vertical), ±2.5m (Horizontal) |
| Max. Speed of Tail Servo Horn | 300 degree/sec |
| MAX. Tilt Angle | 45 Degree |
| Max. Vertical Speed | ±4m/s |
| Max. Flying Speed | 5m/s |
| Axle Base | 350mm |
| Working Temperature | -10 to -50 Celsius Degree |
| Frequency | 2.4GHz ISM |
| Channel for Receiver | 6CH |
| Control Distance | 300 meters (outside or without obstruct) |
| Receiving Sensitivity (1%PER) | >-93dBm |
| Transmitter Power | <20dBm |
| Working Capacity | 52mA@6V |
| Camera Size | 1.2mm (length)* 1.2mm (width)* 9mm (Height) |
| Definition | 600TV lines |
| Image Resolution | 1280*960 |
| Supply Voltage | 3.7V-5V/90 mA |
| Min illumination | 0.5 Lux |
| TV System | PAL |
| Photosensitive Element | 1/4in HD Sensor |
| Brush Frequency | 50f/s PAL |
| Image Color | Multicolor |
| Operating Frequency | 5.8GHz |
| Channels | 4 Channels |
| Communication Distance | 150m (outdoor, no resistance) |
| Input Voltage | 100-240V |
| Charging Current | 1A/2A |
| Balance Current | 200mA |
| Power | 20W |
| 1*3S/11.1V/2200mAh Lipo Battery (flying time | 10min) |
| http | //bbs.5imx.com/bbs/forum.php?mod=viewthread&tid=778800&extra=&page=1 |
Parameters for Quadcopter:, Parameter for Radio Control:, Parameter for Camera:, Parameter for Image Transmission:, Operating Voltage: 5V, Parameter for Charger:, Package Lists:, 1*Apollo Quadcopter RTF, Features:, Engineering plastic and titanium alloy filled in the case, Pre-installation position makes the Gimbal conveniently mount on the bottom and also easily adjust the motions: moving up and down, rolling left and right, Flight Video:,
Without battery 1*6CH Transmitter & Receiver 1* Landing Skid (one ...SDSHobby
2.4G 3 CHANNELS PISTOL TYPE REMOTE CONTROL SET GT2B / TRANSMITTER AND RECEIVER FOR RC BOATS AND CARS
| yes (USB, output | PPM) |
| 90 degree (right | 45 degree; left |
| 45 degree (front | 30 degree; back |
Product Description:, Specifications:, , Channels:, 3, Application Model Type:, RC model cars and boats, RF Range:, .4-2.48GHz, Bandwidth:, 500Hz, Band Qty.:, 160, RF power:, less than 20dBm, .4G System:, GFSK, Code Type:, digital, Resolution:, 1024, Low Voltage Warning:, yes (less than 3.5V), DSC port:, Steering Wheel Angle Range:, Throttle Angle Range:, Charger Port:, yes, Antenna Length:, 6mm, Weight:, 62g, Input Power:, 3.7V (800mA), Size:, 158*94*233mm, Color:, Black, Certificate:, CE0678, FCC, Specifications of FS-GR3F Receiver:, Channels:, 3, Application Model Type:, RC model cars and boats, RF Range:, .4-2.48GHz, Bandwidth:, 500Hz, Band Qty.:, 160, Sensitivity:, -105dBm, .4G System:, GFSK, Code Type:, digital, Resolution:, 1024, Input Power:, 4.5-6.5V DC, Antenna Length:, 6mm, Weight:, 5g, Size:, 35*22*12mm, Color:, Black, Certificate:, CE, FCC, Package Details:,
FS-GT2B uses the first generation of automatic frequency hopping number ...