ReadyMadeRC
GAUI 500X QUAD COMBO INC MOTORS, ESC, BAG, FRAME, NO GU-344
Dimension | (64) |
Dimension | (?) |
500X was designed based on UAV, advantages are:, , 1. Flight Efficiency: Standard Battery (2S2000mAh) time of flight for more than 12min, with a high-capacity battery, the flight time will be 20 min or more (available spreadsheet calculation), 2. Excellent wind resistance: the efficiency and load of propeller are perfectly optimized, so the wind resistance will be better than general electric aircraft, 3. High stability: When using GU-344 (three-axis stabilizing system) for the beginner or professional in combination with other electronics for FPV flying; making the GAUI Quad Flyer a very stable vehicle., 4. Additional payload capabilities: Maximum Flying Weight is between 1100g to 2200g depending on power system used (330X GAUI Motors/ESCs or 500X GAUI Motors/ESCs), you can install cameras and video recorder, and other system., Note: For users who have transplanted GAUI 330X / 330X-S power systems (motors, ESCs) to the 500X Upgrade kit, please use 8 inch propellers., Powered by:, , : type, Product packing:, , Export Carton (LNK):, , Manual:, , * The payload calculations and the battery options :, Ex 1: If the 500X carries a HD Camera (weight 350g) and uses a 3S/2000mah LiPo(weight 150g),the flying weight is 1170g (670+350+150).The power consumption in this condition is 141w(as table above).The Power of this battery is 11.1(V) * 2(A) * 60(Min.) = 1332.The flying time is about 7.1(Min.)Calculation : (1332 / 141) * 75%(Bat. Factor) = 7.1 (Min.) Ex 2: If the 500X uses 2pcs of 3S/2000mah LiPo(in parallel), the flying weight is 1050g (670+350+ 150X2).The power consumption in this condition is 167w(as table above).The total Power of the batteries is 11.1(V) * 2(A) * 60(Min.) * 2 (Bat. in parallel)= 2662.The flying time is about 12(Min.) Calculation : (2662 / 167) * 75%(Bat. Factor) = 12 (Min.)", CAUTION : The Power Consumption Table is calculated based on cruising, the ESC output current may increase 3 or 4 times more for flying mode other than cruising due to increased power output. Make sure to check flyin,
CAN NOT BE BACK ORDERED 500X Quad Flyer Combo Kit ...ReadyMadeRC
900MHZ 500MW TRANSMITTER - US VERSION
CH1 | 910 |
Power requirements | 12V, 500mA |
Frequencies:, , Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
US VERSION LOCKED ON 910MHZ. Great quality video and no ...ReadyMadeRC
1000MW 1300MHZ TRANSMITTER - NEW CUSTOM READYMADERC US VERSION
Output Power | 1000mW (see above) |
Nominal output impedance | 50 ohms |
Operating voltage | 10.5-13V DC (will function at lower power at lower voltages listed above) |
Supply current | 500mA (maximum) |
Sub carrier frequency | 6.5MHz |
Dimension | 45 x 28 x 9mm |
Weight (transmitter only) | 22g |
Includes | Transmitter |
*Notice: The use and operation of this product in the USA and other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
WE'VE OPENED UP A WHOLE NEW FREQUENCY FOR LEGAL USE ...ReadyMadeRC
1000MW 1300MHZ TRANSMITTER - NEW CUSTOM READYMADERC INTL VERSION
Output Power | 1000mW (see above) |
Nominal output impedance | 50 ohms |
Operating voltage | 10.5-13V DC (will function at lower power at lower voltages listed above) |
Supply current | 500mA (maximum) |
Sub carrier frequency | 6.5MHz |
Dimension | 45 x 28 x 9mm |
Weight (transmitter only) | 22g |
Includes | Transmitter |
Frequencies:, 1258, *Notice: The use and operation of this product in the USA and other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
WE'VE OPENED UP A WHOLE NEW FREQUENCY FOR LEGAL USE ...ReadyMadeRC
1.3GHZ 300MW TRANSMITTER - NEW CUSTOM READYMADERC US VERSION
CH1 | 1258 MHz |
CH2 | 1280 MHz |
Power requirements | 12V, 500mA |
Weight | 30g (transmitter and antenna, no cables) |
Frequencies:, , Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
WE'VE OPENED UP A WHOLE NEW FREQUENCY FOR LEGAL USE ...ReadyMadeRC
1.3GHZ 300MW TRANSMITTER - NEW CUSTOM READYMADERC INTL VERSION
CH1 | 1258 MHz |
CH2 | 1280 MHz (ON, OFF) |
CH3 | 1320 |
CH4 | 1360 |
Power requirements | 12V, 500mA (3s lipo) |
Weight | 30g (transmitter and antenna, no cables) |
Frequencies and DIP switch positions (1, 2):, , Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
WE'VE OPENED UP A WHOLE NEW FREQUENCY FOR LEGAL USE ...ReadyMadeRC
RMRC - 1.3GHZ 150MW TRANSMITTER - US VERSION
CH1 | 1258 MHz |
CH2 | 1280 MHz |
Power requirements | 12V, 200mA |
Weight | 22g (transmitter and antenna, no cables) |
Frequencies:, , NOTE: THESE TRANSMITTERS MAY ONLY WORK PROPERLY WITH THE STOCK ANTENNA. The transmitters are tuned at the factory using these antennas, and non-stock antennas may change the feedback the transmitter receives, which may cause the transmitter to operate on the incorrect frequency. In testing the power output of these units vary from about 75mW to 160mW from unit to unit., Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
Now includes the original 1280MHz, along with the new 1258MHz ...ReadyMadeRC
RMRC - 1.3GHZ 150MW TRANSMITTER - INTL VERSION
CH1 | 1258 MHz |
CH2 | 1280 MHz |
CH3 | 1320 MHz |
CH4 | 1360 MHz |
Power requirements | 12V, 200mA |
Weight | 22g (transmitter and antenna, no cables) |
Frequencies:, , NOTE: THESE TRANSMITTERS MAY ONLY WORK PROPERLY WITH THE STOCK ANTENNA. The transmitters are tuned at the factory using these antennas, and non-stock antennas may change the feedback the transmitter receives, which may cause the transmitter to operate on the incorrect frequency. In testing the power output of these units vary from about, Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
Now includes three of the the original frequencies, along with ...ReadyMadeRC
100MW 5.8GHZ A/V TRANSMITTER (FATSHARK)
Frequencies | 5740, 5760, 5780, 5800, 5820, 5840, 5860MHz |
Weight | 20 grams |
Size | 57 x 34mm |
Input voltage range | 6 - 12vDC |
Input power | 1.5W |
Notice: The use and operation of this product in the USA and many other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
High Quality 100mW 5.8GHz transmitter. Compatible with ImmersionRC, FatShark, and ...ReadyMadeRC
1000MW 900MHZ TRANSMITTER - US VERSION
Output Power | 1000mW |
Nominal output impedance | 50 ohms |
Operating voltage | 10.5-13V DC (will function at lower power at lower voltages listed above) |
Supply current | 500mA (maximum) |
Sub carrier frequency | 6.5MHz |
Dimension | 50 x 25 x 7mm |
Weight (transmitter only) | 10g |
Includes | Transmitter |
*Notice: The use and operation of this product in the USA and other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
A high quality, low weight, high powered transmitter in the ...ReadyMadeRC
RMRC - 900MHZ 1000MW TRANSMITTER - INTL VERSION
Output Power | 1000mW |
Nominal output impedance | 50 ohms |
Operating voltage | 10.5-13V DC (will function at lower power at lower voltages listed above) |
Supply current | 500mA (maximum) |
Sub carrier frequency | 6.5MHz |
Dimension | 50 x 25 x 7mm |
Weight (transmitter only) | 10g |
Includes:, , Frequencies:, , *Notice: The use and operation of this product in the USA and other countries requires an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
THIS IS THE INTERNATIONAL VERSION, ANYONE IN THE US SHOULD ...ReadyMadeRC
900MHZ 500MW TRANSMITTER - INTL VERSION
CH1 | 910 |
CH2 | 980 |
CH3 | 1010 |
CH4 | 1040 |
Power requirements | 12V, 500mA |
Frequencies:, , Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
INTERNATIONAL VERSION, CANNOT SHIP TO A US ADDRESS UNDER ANY ...ReadyMadeRC
RMRC - 900MHZ 200MW TRANSMITTER - US VERSION
CH1 | 910 MHz (Only channel for units shipped to USA) |
Power requirements | 12V, 200mA |
Frequencies:, , NOTE: THESE TRANSMITTERS MAY ONLY WORK PROPERLY WITH THE STOCK ANTENNA. The transmitters are tuned at the factory using these antennas, and non-stock antennas may change the feedback the transmitter receives, which may cause the transmitter to operate on the incorrect frequency., Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations.,
US VERSION LOCKED ON 910MHz Great quality video and no ...ReadyMadeRC
RMRC - 900MHZ 200MW TRANSMITTER - INTL VERSION
CH1 | 910 MHz (Only channel for units shipped to USA or Canada) |
CH2 | 980 MHz |
CH3 | 1010 MHz |
CH4 | 1040 MHz |
Power requirements | 12V, 200mA |
Frequencies:, , NOTE: THESE TRANSMITTERS MAY ONLY WORK PROPERLY WITH THE STOCK ANTENNA. The transmitters are tuned at the factory using these antennas, and non-stock antennas may change the feedback the transmitter receives, which may cause the transmitter to operate on the incorrect frequency.,
INTERNATIONAL VERSION, CANNOT SHIP TO A US ADDRESS UNDER ANY ...ReadyMadeRC
L-C FILTER FOR WIRELESS A/V SYSTEMS
Manual | PSF-100 |
Note: Installations with severe power supply noise may not be fully cured with this filter. In such cases a shared battery should be avoided., Installation requires soldering in-series with the noisy power supply, as follows:, ,
This compact supply filter helps clean up dirty DC power ...