RCTimer
SK-20A SIMONK FIRMWARE MULTICOPTER SPEED CONTROLLER ESC 20A
| The Newest SimonK Firmware | rctimer_tgy_2012-12-14Input voltage |
RCTimer
RC CAR QUIK ESC 30A BRUSHLESS MOTOR SPEED CONTROLLER
| 10)、Support 1 cell operation (min voltage | 3V, only available for XC-6A and XC-10A). |
| · Input voltage | 5V-13V (support 2-3 lithium batteries) |
| · Continue current | 30A |
| · BEC output | 2A /5V (linear) |
| · Size( length X width X high) | 45x32x20 mm |
| · Weight | 51 g |
| 4)．Run Mode | One, Two, Two2. Default is Two2. |
| One | the car can go forward only, and brake continuously if push the throttle stick to backward zone. |
| 5)．Start Force | 20%,25%,30%,35%,40%. Default is 30%. It refers to the maximum force when the car start. |
| 6)．Timing | low, middle ,high and highest. Default is middle. Low advance timing is recommended |
1). OffVolt (Low voltage Protection threshold, Cutoff voltage): User can set proper cutoff voltageaccording to cell quantity in range of 00.0-49.9V, the default is 00.0V。, Note: System will detect battery cells and calculate proper threshold automatically if this setting is 00.0V, protection threshold for each Li-XX cell is 2.8V. For example: if the battery pack is 3 cells Li-xx, cutoff voltage will be: 2.8V*3=8.4V., 2)．Brake Force: 50%, 75%,100%. Default is 100%. The ESC provide proportional brake function. The brake forceis related to the position of the throttle stick. It refers to the maximum brake force when the throttle stick is pushed to the top point of the backward zone., 3)．Drag Brake: 0、5%,10%,15%,20%. Default is 0. When the throttle stick is located at the neutral zone,the ESC provide a slight brake force., Two: Bi-directional mode, the car go forward when the throttle stick is located at the forward zone,when the throttle stick is located at the backward zone, the car will go backward, the brake will occur when direction change., Two2: Conditional Bi-directional mode. With this option, the car go backward only when car is stop and throttle stick is pushed from neutral zone to backward zone. When car is running forward, push throttle stick to backward zone, car will keep brake until it stops, the throttle stick return the neutral zone, and push the throttle stick to the backward zone, then the car will go backward.,
1、Features 1)、Full protection feature including low voltage, over-heat, throttle signal ...RCTimer
RCTIMER ESC 20A BRUSHLESS MOTOR SPEED CONTROLLER
| Input voltage | DC 6-16.8V(2-4S Lixx) |
| BEC | 5V 2amp |
| Running current | 20A(Output |
| Size | 36mm (L) * 26mm (W) * 7mm (H). |
| Weight | 22g. |
| Input voltage | DC 6-16.8V(2-4S Lixx) |
| BEC | 5V 2amp |
| Running current | 20A(Output |
| Size | 36mm (L) * 26mm (W) * 7mm (H). |
| Weight | 22g. |
| Package | 1* 20A ESC |
Programmable Items:, 1. Brake Setting：Enabled / Disabled, default is Disabled, 3. Low Voltage Protection Mode(Cut-Off Mode)： Soft Cut-Off (Gradually reduce the output power) or Cut-Off (Immediately stop the output power). Default is Soft Cut-Off. Input voltage:DC 6-16.8V(2-4S Lixx), Programmable Items:, 1. Brake Setting：Enabled / Disabled, default is Disabled, 1) For lithium batteries, the number of battery cells is calculated automatically. Low / medium / high cutoff voltage for each cell is: 2.6V/2.85V/3.1V. For example: For a 3 cells lithium pack, when “Medium” cutoff threshold is set, the cut-off voltage will be: 2.85*3=8.55V., 2) For nickel batteries, low / medium / high cutoff voltages are 0%/45%/60% of the startup voltage (i.e. the initial voltage of battery pack), and 0% means the low voltage cut-off function is disabled. For example: For a 10 cells NiMH battery, fully charged voltage is 1.44*6=8.64V, when “Medium” cut-off threshold is set, the cut-off voltage will be:8.64*50%=4.3V。,
Programmable ESC 20A Brushless Motor Speed Controller Hobbywing's Program 2. ...RCTimer
RC HOBBIES ESC 70A BRUSHLESS MOTOR SPEED CONTROLLER
| - Throttle setting | auto or 1.1ms to 1.8ms |
RCTimer
RCTIMER ESC 40A BRUSHLESS MOTOR SPEED CONTROLLER
,
RCTIMER V2 40 Amp ESC with built-in 3A BEC Hobbywing's ...RCTimer
SK-40A SIMONK FIRMWARE MULTICOPTER SPEED CONTROLLER ESC 40A
| Note | This ESC don't included manual. |
| Package | 1* 40A ESC |
The Newest SimonK Firmware:, rctimer_tgy_2012-12-14,
RCTimer SK ESC 40A Brushless Motor Speed Controller The code ...RCTimer
RC HOBBIES ESC 100A BRUSHLESS MOTOR SPEED CONTROLLER
| Timing Mode Setting | 1º /7º /15º/30º |
| PWM Setting | 8K/16K |
BEC: No, Important Note: this ESC is Opto, without BEC supplying power to your Receiver, you need extra power source for your receiver. You can use a UBEC, a voltage regulator, or extra batteries as the power source for your receiver. If you hear the music tone repeat again and again for more than 3 times, you may need to check your power source to the receiver.,
ESC 100A Brushless Motor Speed Controller Constant current 100A Max ...RCTimer
RC CAR ESC 50A BRUSHLESS MOTOR SPEED CONTROLLER
| Brand | RCTimer |
| Unit | Pcs |
| Weight | 0.070 kg |
| Features | Suitable Car |
| TotalRate | var stari_1 = new star5('si_1');stari_1.initial();stari_1.redraw(0); Review Summary |
| Write a Review 1.1 Output | Continuous current 40A, working current at 50A can last over 1 minute,burst current 60A. 1.2 Input |
| 1.3 BEC Output | 6V/1A. |
| 1.4 Resistance | 0.0006 Ohm. |
| 1.5 Motor Supported | Sensored brushless / Sensorless Brushless / Brushed |
| 1.6 Suitable Brushless Motor | 5.5T and >5.5TÂ Â Â |
Score : 37, 1.7 Suitable Car:  1/10, 1/12 on-road or off-road cars / trucks for normal race.(Great power for 2S lipo battery) 1.8 Size: 31.5mm(L) * 27.5mm(W) * 24mm(H). 1.9 Weight: 30g(Without wires),
RCTimer
RCTIMER ESC 18A BRUSHLESS MOTOR SPEED CONTROLLER
| Input voltage | DC 6-16.8V(2-4S Lixx) |
| BEC | 5V 2amp |
| Running current | 18A(Output |
| Size | 26mm (L) * 26mm (W) * 7mm (H). |
| Weight | 18g. |
Programmable Items:, 1. Brake Setting, the number of battery cells is calculated automatically. Low / medium / high cutoff voltage for each cell is: 2.6V/2.85V/3.1V. For example: For a 3 cells lithium pack, when “Medium” cutoff threshold is set, the cut-off voltage will be: 2.85*3=8.55V., low / medium / high cutoff voltages are 0%/45%/60% of the startup voltage (i.e. the initial voltage of battery pack), and 0% means the low voltage cut-off function is disabled. For example: For a 10 cells NiMH battery, fully charged voltage is 1.44*6=8.64V, when “Medium” cut-off threshold is set, the cut-off voltage will be:8.64*50%=4.3V。,
：Enabled / Disabled, default is Disabled 2. Battery Type ：Li-xx(Li-ion ...RCTimer
BEC 3A@5V ESC 50A BRUSHLESS MOTOR SPEED CONTROLLER
| Weight | 48g |
| Size(mm) | 50*32*10 |
| Continuous current | 50A |
| Burst current | 60A |
| BEC | 5V3A |
| PWM | programmable - 8/16K |
| Battey | 4-12 Ni-Mh/Ni-Cd or 2-4 Lipo |
RCTimer
RC HOBBIES ESC 125A BRUSHLESS MOTOR SPEED CONTROLLER
| Timing Mode Setting | 1º /7º /15º/30º |
| PWM Setting | 8K/16K |
BEC: No, Important Note: this ESC is Opto, without BEC supplying power to your Receiver, you need extra power source for your receiver. You can use a UBEC, a voltage regulator, or extra batteries as the power source for your receiver. If you hear the music tone repeat again and again for more than 3 times, you may need to check your power source to the receiver.,
ESC 125A Brushless Motor Speed Controller Constant current 125A Max ...RCTimer
RC HOBBIES ESC 80A BRUSHLESS MOTOR SPEED CONTROLLER
| - Throttle setting | auto or 1.1ms to 1.8ms |
RCTimer
RCT ESC 3A BRUSHLESS MOTOR SPEED CONTROLLER
| Brand | RCTimer |
| Unit | Pcs |
| Weight | 0.030 kg |
| TotalRate | var stari_1 = new star5('si_1');stari_1.initial();stari_1.redraw(0); Review Summary |
Features :::ListPrice : $ 14.99, Score : 6, Write a Review,
RCTimer
HOBBYWING LED PROGRAM CARD FOR RC BOAT BRUSHLESS ESC (VERSION2)
| Brand | Hobbywing |
| Unit | Pcs |
| Weight | 0.050 kg |
| Features | Version 2 |
| TotalRate | var stari_1 = new star5('si_1');stari_1.initial();stari_1.redraw(0); Review Summary |
| Write a Review 1.1 Size | Â 88mm (L) * 58mm (W) * 14mm (H) |
| 1.2 Weight | Â Â 40g. |
Score : 8, 1.3 Input Voltage:  4.8-6V (If the ESC hasn’t a built-in BEC, you must use an additional battery pack to supply the program card)   2  Programmable Items  , C)  The programmable items of LED_PC2C  (Available for XERUN and EZRUN series car ESC of Version2)  #1    Running Mode #2    Drag Brake Force #3    Low Voltage Cut-Off Threshold #4    Start Mode #5    Maximum Brake Force #6    Maximum Reverse Force #7    Initial Brake Force #8    Throttle Neutral Range #9    Timing #10  Over-Heat Protection #11    Motor Rotation #12    Lipo Cells (Note: The item #11 and #12 are not available for XERUN series ESC of Version 2, they only available for EZRUN series ESC)   ,         Front Panel Picture of LED_PC2C:,
 This program card is used to set the programmable ...RCTimer
HOBBYWING LED PROGRAM CARD FOR RC CAR BRUSHLESS ESC (VERSION2)
| Brand | Hobbywing |
| Unit | Pcs |
| Weight | 0.050 kg |
| Features | Version 2 |
| Score | 8 1.1 Size |
| 1.2 Weight | Â Â 40g. |
1.3 Input Voltage:  4.8-6V (If the ESC hasn’t a built-in BEC, you must use an additional battery pack to supply the program card)   2  Programmable Items  , C)  The programmable items of LED_PC2C  (Available for XERUN and EZRUN series car ESC of Version2)  #1    Running Mode #2    Drag Brake Force #3    Low Voltage Cut-Off Threshold #4    Start Mode #5    Maximum Brake Force #6    Maximum Reverse Force #7    Initial Brake Force #8    Throttle Neutral Range #9    Timing #10  Over-Heat Protection #11    Motor Rotation #12    Lipo Cells (Note: The item #11 and #12 are not available for XERUN series ESC of Version 2, they only available for EZRUN series ESC)   ,         Front Panel Picture of LED_PC2C:,
 This program card is used to set the programmable ...