Skip to content
Discountinued

ReadyMadeRC

SkyWalker FPV Pan/Tilt Pod Kit


ManualHERE

When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required.  The system was designed for TG9e servos.  Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,

An FPV pod for the SkyWalker that offers a custom mechanism allowing for full 180 degree (+/- 90 degree) panning without the need for any modifications to a servo or without the need for a servo stretcher.  A full 360 degree pan (+/- 180 degrees) is possible with the addition of an NG Hobbies SSV3.5 servo stretcher (option below).

It has also been reported that this pod fits the "FPV 168" plane with very little modification required.

The pods are supplied with quality TG9e servos.  For better resistance to crash damage HS-65HB servos are available as an upgrade option below.

A support at the rear of the pod is available for your battery(two locations to choose from!).  Although designed for a 620mAh 3s battery, many other batteries will fit in this compartment.

The pod is attached to the Skywalker by a combination of the tabs at the rear of the pod and a thumb screw (included) at the front of the pod that attaches to the blind nut that comes with the SkyWalker.

There are two locations for the pan/tilt assembly.  You can choose a normal or forward location during assembly (see pictures).

RMRC-420, RMRC-420XV, RMRC-520, RMRC-LL600, KX131, KX171, KX191, IF Cam, SN777, SN555 and others

Additional back plates may be purchased
here
to fit RMRC-480, RMRC-540, IF OSD Cam, DPC OSD Cam, DX201

If you need to mount a camera not listed, please send me a message via the "Contact Us" link to the left.

Laser cut components for the main pod

Laser cut components and hardware for the 180 degree pan module (or other options available)

Two 9g Servos (if choosing a pan/tilt option with basic servos)

Thumb screw and retaining clip

Velcro strap to hold battery to pod

Double sided servo tape to apply TX, camera, and tilt servo.

Pull-ties to hold TX against tape and for holding your wiring down.

Medium CA

*No pan/tilt module option will come with laser cut parts for pod, thumb screw, retaining clip, and velcro strap.


Check price and availability


Found 11 years, 8 months ago



Related Products


SkyWalker FPV Pan/Tilt Pod Kit

View
SkyWalker FPV Pan/Tilt Pod Kit

Skywalker Version 5 (2012) EPO FPV Gilder w/ ...

View
Skywalker Version 5 (2012) EPO FPV Gilder w/ Steel Tube Special Offer

Radian FPV Pan/Tilt Pod Kit

View
Radian FPV Pan/Tilt Pod Kit

ImmersionRC FPV EZAntenna Tracker (for EzOSD)

View
ImmersionRC FPV EZAntenna Tracker (for EzOSD)

FPV Flight Simulator Joystick - FPV 1.5 Interface ...

View
FPV Flight Simulator Joystick - FPV 1.5 Interface - X-Gyro 1500
BevRC DPCAV Hobby-Lobby HobbyKing LowPriceRC ngHobbies NitroTek R2Hobbies RangeVideo RCTimer ReadyMadeRC HobbyWireless RCPlanet HorizonHobby HiModel OFM GetFPV AMainHobbies SDSHobby GoodLuckBuy Flying-Hobby