HiModel
CYCLOPS EASY OSD FPV SYSTEM W/GPS
, , , , , , Specifications:, , , , , , , , , , , CYCLOPS EASY OSD FPV System W/GPS, , ,
Features: Feature: Easy OSD is featured in small dimension, light ...6 Reviews
HiModel
5.8GHZ BUILT-IN RECEIVER 7 INCH 800X480 MONITOR W/LIGHT SHIELD
| 2. Screen type | TFT LCD Screen/long life, LED backlight |
| 3. Resolution | 800*480 |
| 4. Brightness | 450cd/m2 |
| 5. Contrast | 500 |
| 6. View Angle | 140/120degree (Horizontal/Vertical) |
| 7. Working Voltage | DV 7-13V(center positive) or 11.1V Li-battery |
| 9. Size | 170mm x 110mm x 40mm |
| 11. Input | 2 ways video including AV1 for built-in receiver, one way audio |
| 12 Output | 1 way |
| 14. Working temperature | -10℃~+ 65 ℃ |
| 15. Receiver antenna connector type | RP-SMA, jack (monitor side) |
| • CH1 | 5705MHz |
| • CH2 | 5685MHz |
| • CH3 | 5665MHz |
| • CH4 | 5645MHz |
| • CH5 | 5885MHz |
| • CH6 | 5905MHz |
| • CH7 | 5925MHz |
| • CH8 | 5945MHz |
, , , , , , Specifications:, , , , , , , , , , , Specification:, 1. Screen size:7”, 8. Power Consumption: , 10. Built-in 5.8Ghz receiver (RC305 5.8G), 13. Support 9 languages menu selection including English., See connector type diagram, Working frequencies (* Check your TX frequency to make sure they are supported by your TX), , ,
Features: Features: -Built-in 5.8G Receiver -None "blue screen" effect when ...1 Reviews
HiModel
X-CAM 2 AXIS GIMBAL STABILIZATION MODULE GSM110
| 1. 2 Axis Stabilization | GSM110, GSM210 |
| 2. 3 Axis Stabilization | GSM120, GSM220 |
, , , , , , Specifications:, , , , , , , , , , , X-CAM 2 Axis Gimbal Stabilization Module GSM110, Specification：, Input Voltage： 5, - 6V, Volume：, 45 x 35 x 10 mm, There are 4 versions of this series product available, And this one is version GSM110., How to use the Remote Controller for Servo Reverse Setup ：, 1. Connect to channel CH5 on the Printed Circuit Board (PCB), 2. Push this channel to the highest position on your Remote Controller, 3. There will be 3 BEEPs followed by the Red LED flashing, Return the Remote Controller Lever to the middle position to enter the Servo Reverse Setup mode, 4. Move the Remote Controller Lever to the Highest or lowest position to set the Servo Reverse after hearing the BEEPs., (One BEEP means Channel 1 (TILT) , Two BEEP means Channel 2 (ROLL), Three BEEP means Channel 3 (PAN) ),, If you do not want to change the setup, Just move the Remote Controller Lever to the Middel position., 5. When you hear 4 BEEPs, the setup has been saved., How to adjust the Acc. Gain:, Rotate the Blue Potentiometer on the PCB for adjust the Acc. Gain., PC software for setup, , ,
Includes/Requires: Includes: 1 x Gimbal Stabilization Module 1 x USB ...HiModel
HIMODEL 5.8G 1000MW (1W) HIGH POWER TRANSMITTING MODULE (TX) -GOLDEN EDITION | SMA, JACK
| video format supported | NTSC/PAL |
| Connector type | SMA Jack (on the TX module side) |
| Transmitting power | 1000mW |
| Power input | 7.4-13V (3S Lipo suggested, does NOT support 4S Lipo) |
| Transmitting current | 600mA @12V |
, , , , , , Specifications:, , , , , , , , , , , HiModel 5.8G 1000mW (1W) High Power Transmitting Module (TX) -Golden Edition, Refer to here for connector type diagram, ,
Features: New 5.8G 1000mW Golden version. - Upgraded ball bearing ...HiModel
FPV 5.8G 1000MW A/V TRANSMITTER MODULE (TX) | (SMA, JACK)
| video format supported | NTSC/PAL |
| Antenna connector | SMA jack (module side) |
| Power input | 7-15V (3S Lipo suggested, does NOT support 4S Lipo) |
| Transmitting current | 500mA (600mA at 12V under our real testing) |
| Dimension | 59x27x33 (excluding antenna) |
| Weight | 52.9g (with antenna) |
, , , , , , Specifications:, , , , , , , , , , , FPV 5.8G 1000mW A/V Transmitter Module (TX), Refer to here for connector type diagram, *Note: TX antenna must be installed properly before it is switched on, power on without install antenna, or a improper antenna was used may easily burn the TX, and such damage is not covered by warranty., , ,
Features: FPV 5.8G 1000mW A/V Transmitting module, a good choice ...1 Reviews
HiModel
G.T.POWER FPV 5.8G 250MW A/V TRANSMITTING/RECEIVING COMBO (TX/RX) | RP-SMA, JACK
| Video Format | Pal/NTSC |
| Output impedance | 50 Ohm |
| Output power | 21-23 dBm |
| Transmitter operating voltage | 7.4-12.6 V DC/200mA |
| Video bandwidth | 0-8.0 MHZ |
| Audio input impedance | 10K/Ohm |
| Audio input level | 0.5-2.0 Vp-p |
| Audio frequency | 6.5 MHZ |
| Antenna connector | RP-SMA, jack (TX side) |
| Video input level | 0.8-1.2 Vp-p |
| Video input impedance | 75 Ohm |
| Dimensions | 55x26x17 mm |
| Weight | 25 g |
| Operating temp | -10~85 ℃ |
| Audio frequency | 6.5 MHz |
| Video input impedance | 75 Ohm |
| Audio input impedance | 10K/Ohm |
| Antenna connector | RP-SMA jack (RX side) |
| Channels 5.8G | 5705,5685,5665,5645,5885,5905,5925,5945 MHZ |
| Receiver operating voltage | 7.4~12.6 V DC |
| Video bandwidth | 0~8.0 MHz |
| Video input level | 0.8~1.2 Vp-p |
| Audio input level | 0.5~2.0 Vp-p |
| Weight | 43 g |
| Dimensions | 61x52x13 mm |
, , , , , , Specifications:, , , , , , , , , , , TX specs:, Channels: 8, See connector type diagram, RX specs:, Channels: 8, , ,
Includes/Requires: Includes: 1 x transmitting unit (TX) 1 x receiver ...1 Reviews
HiModel
USB UPGRADE CABLE FOR FRSKY DHT-U FUC-2
, , , , , , Specifications:, , , , , , , , , , , USB Upgrade Data Cable for FrSky DHT-U, , ,
HiModel
FRSKY LIPO VOLTAGE SENSOR FLVS-01
| Model | FLVS-01 |
| Dimension | 45*21*7mm |
| Weight | 5.2g |
| Measurement range | 1S~6S (The first lipo voltage should be more than 3.55V) |
| Cell voltage display range | 0.20~4.20V |
| Voltage display resolution | 0.01V |
| Voltage detection precision | 0.03V |
| Current of the board | 15.5mA |
| Operating temperature range | -30℃~70℃ |
| Pixel | 128*64 with OLED display screen |
, , , , , , Specifications:, , , , , , , , , , , Specifications:, ﹡Note:, To make the FLVS-01 works with sensor hub and FLD-02/DHT-U to display total voltage and cell voltages as connected, you may need to upgrade your firmware of sensor hub and DHT-U to version 2.0, refer to included instruction manual for details., , ,
Features: Different sensors facilitate to monitor different data, such as ...HiModel
3K GLASSY CARBON SHOCK ABSORBING PLATE A16W/16 DAMPING BALLS (SUIT FOR DSLR)
| Dimension | 133 x 131 x 20mm (approx.) |
| Material | 3K Glassy Carbon |
| Plate thickness | 2mm |
| Suitable camera | Digital Single Lens Reflex Cameras. |
| Weight | 78g |
Specifications:, 3K Glassy Carbon Shock Absorbing Plate A16W/16 Damping Balls (suit for DSLR), Damping ball number: 16, * Not pre-assembled., ,
Features: Application: Hooked between multi-rotor craft and gimbal, eliminates vibration ...HiModel
10 INCH 1024X600 RESOLUTION FIELD MONITOR W/SUNLIGHT SHIELD FPV-101AH-450
Specifications:, ,
Features: Includes/Requires:HiModel
M5XL53 CNC ALUMINUM HAND FASTEN CAMERA SCREW FOR GOPRO - RED
Specifications:, ,
Features: Includes/Requires:HiModel
M5XL53 CNC ALUMINUM HAND FASTEN CAMERA SCREW FOR GOPRO - TITANIUM
Specifications:, ,
Features: Includes/Requires:HiModel
CONTROLABLE TILT UNIT FOR LOTUSRC T580 QUADCOPTER
| Width | 11cm |
| Height | 7cm |
| Total width of the tilt mount | 14.5mm |
| Total height of the tilt mount | 15.5mm |
| Mounting stick spacing(approximately) | 86mm / 70mm |
| Weight | 93g |
, , , , , , Specifications:, , , , , , , , , , , Max camera size it can adopt:, , ,
Features: Controlable Tilt Unit for LOTUSRC T580 Quadcopter . Controlable ...HiModel
HI582 5.8G A/V DIVERSITY RECEIVER | SMA, JACK
| CH1 | 5705MHz CH2 |
| CH5 | 5885MHz CH6 |
| Video Output | 75Ω/1Vpp |
| Audio Output | 10KΩ/500mVpp |
| TV System | PAL/NTSC/SECAM |
| Input Voltage | 12V/500mA |
| Weight | 197 g |
| Size | 76x64x18mm |
| Antenna connector | SMA, jack (module side) |
, , , , , , Specifications:, , , , , , , , , , , Receiver Frequency:, Refer to here for connector type diagram, * Plate type antennas are not included (to be purchased separately)., , ,
Features: Features: Twin Receiver for best reception Automatic ...1 Reviews
HiModel
FPV 420-LINE CAMERA 1/3 SONY CCD - PAL FORMAT
| Sensor | 1/3 CCD Sony, 420 lines. |
| Video format | PAL |
| Power Input | 12V ±5% |
| Shutter speed | automated 1/50-1/10000 sec |
| Minimum illuminance | 0.05Lux F2.0 |
| Dimension | 35 x 35 x 35mm (excluding mount) |
| Weight | 50.9g |
, , , , , , Specifications:, , , , , , , , , , , FPV 420-line Camera 1/3 Sony CCD, Audio: No, Current consumption: , , ,
Includes/Requires: Includes:1 x camera 1 x wire 1 x instruction ...3 Reviews