RC Model Motors, Gas, Glow Page 4 Review

HobbyKing

TRACKSTAR SEG 21 TWO STROKE GLOW RACING ENGINE FOR CAR

Displacement	3.45CC
Bore	16.26mm
Stroke	16.80mm
Carburetor	8mm
Crankshaft	14mm SG
RPM	6,000~38,000
Maximum Power	2.6hp
Weight	342g

Features:, • High performance and high torque ABC liner with 3 by-pass ports, Ports:3,

Looking to add some power to your 1/8 off road ...

5 Reviews

HobbyKing

TRACKSTAR SEG 21 RACING ENGINE - REPLACEMENT REAR COVER

TrackStar SEG 21 Racing Engine replacement rear cover.

HobbyKing

JC23 EVO 2 BEAM MOUNT GAS ENGINE W/CD-IGNITION 23CC/3.5HP @ 9,000RPM

Bore/Stroke	33.5 x 30
Piston displacement	23cc
Max. power	3.5HP/9,000rpm
Min. idle rotating speed	1300rpm
Rotate Speed	1,300rpm-9,000rpm
Electronic ignition	CDI
Spark plug	CM-6 style
Length from carb to rear mount hole centre line	54mm
Mount Hole Spacing	25mm
Distance from front mount hole centre line to prop boss	57mm
Height from Crank Centerline to Spark Plug Tip	117mm
Prop Range	15x10 to 18x8

Engine type:, single cylinder, 2-stroke, air-cooled, Carburetor:, Walbro choke type/diaphragm carburetor, Start mode:, Anticlockwise Push Prop Start, Weight:, 760g (Complete except Ignition + 120g, Exhaust + 90g ),

JC23 EVO 2 Beam Mount Gas engine w/CD-Ignition 23cc/3.5hp @ ...

5 Reviews

HobbyKing

REPLACEMENT COMPLETE IGNITION SET FOR SINGLE CYLINDER GAS ENGINES 14MM PLUG

Includes:, Ignition Unit w/HT lead & 14mm Plug Cap,

Replacement Complete Ignition Set for Single Cylinder Gas Engines 14mm ...

5 Reviews

HobbyKing

DJ-80CC GAS ENGINE VERSION 2 W/ CD-IGNITION 8.2HP

Bore x stroke	52 x 38mm
Piston displacement	80cc
Max. power	8.2HP/8,000rpm
Min. idle rotating speed	1200rpm
Rotate Speed	1,200rpm-9,000rpm
Spark plug	NGK CM-6 style
Prop Range	23x10~26x8

Specification:, Carburetor:, Walbro choke type/diaphragm, Start mode:, Anticlockwise Push Prop Start, Weight:, 1795g (without ignition or muffler),

DJ-80cc Gas engine w/ CD-Ignition 8.2HP, a nice quality and ...

HobbyKing

NGH GT25 25CC GAS ENGINE WITH RCEXL CDI IGNITION (2.7HP)

Do not run with less than the manufacturers recommended fuel	oil ratio!

Engine type:, Bore/Stroke:, Piston displacement:, Max. power:, Min. idle Rpm:, Practical RPM:, Ignition:, Spark plug:, Carburetor:, Lubrication oil:, General use fuel:, Propeller range:, Length backplate to propeller boss:, Mounting:, Height from crank centreline to spark plug tip:, Weight:,

This is the GT25 25cc (1.52cu) Gas engine from NGH. ...

HobbyKing

O.S. GT60 GAS ENGINE

• Connecting rod features needle roller bearings at both ends allowing for 50	1 fuel/oil mixture
Recommended Prop Sizes	E-6020 Muffler

A rear-mounted Walbro carburetor is custom designed for the GT60 the IG-02 ignition system provides dependable operation. A choke rod guide has been integrated into the crankcase for effortless set-up. Dual roller bearings on the the connecting rod allows you to run up to 50:1 fuel/oil mixture, (check oil brand) which is very clean running compared to messy nitro fuel. Balanced, optimized crankshaft for vibration control and improved performance. Twin ball bearings support the hardened steel crankshaft for the ultimate in efficiency. Fuel for this engine is recommended to use 87 octane and a quality 2-stroke oil, mixed at 30~50 parts fuel, to 1 part oil., Displacement:, Bore:, Stroke:, Practical rpm:, Output:, Engine Weight:, Ignition Module Weight:, Muffler Weight:,

In 1936, Shigeo Ogawa set up his original machine-shop, making ...