Skip to content
Discountinued

ReadyMadeRC

Pololu 5V Step-Up Voltage Regulator U3V12F5


input voltage2.5 V – VOUT
small size0.515" × 0.32" × 0.1" (13 × 8 × 3 mm)
The boost regulator has three connectionsinput voltage (VIN), ground (GND), and output voltage (VOUT).
Size0.32″ × 0.515″ × 0.1″
Weight0.4 g
Minimum operating voltage2.5 V
Maximum operating voltage5 V
Maximum input current1.4 A
Output voltage5 V
Maximum quiescent current2 mA

Reverse voltage protection?:  N, Notes:,

Great as a step up regulator to go from a 1s lipo to 5v for the pico transmitters and cameras, the compact (0.32"×0.515") U3V12F5 switching step-up (or boost) voltage regulator takes an input voltage as low as 2.5 V and efficiently boosts it to 5 V. The pins have a 0.1" spacing, making this board compatible with standard solderless breadboards and perfboards.

Overview

These boost (step-up) voltage regulators generate higher output voltages from input voltages as low as 2.5 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) and have a typical efficiency between 80% to 90%. The available output current is a function of the input voltage, output voltage, and efficiency (see Typical Efficiency and Output Current section below), but the input current can typically be as high as 1.4 A.

The regulator’s thermal shutdown prevents damage from overheating, but it does not have short-circuit or reverse-voltage protection.

Features

fixed 5 V, 9 V, or 12 V output with 4% accuracy
1.4 A switch allows for input currents up to 1.4 A
2 mA typical no-load quiescent current
integrated over-temperature shutoff

Using the Regulator
Connections

The input voltage, VIN, must be at least 2.5 V and should not exceed the output voltage, VOUT. Please be wary of destructive LC spikes that might cause the input voltage to exceed VOUT (see below for more information).

The three connections are labeled on the back side of the PCB, and they are arranged with a 0.1" spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1" grid. You can solder wires directly to the board or solder in either the 3×1 straight male header strip or the 3×1 right-angle male header strip that is included.

Typical Efficiency and Output Current

The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graphs below, this switching regulator typically has an efficiency of 80 to 90%.

The maximum achievable output current is approximately proportional to the ratio of the input voltage to the output voltage. If the input current exceeds the switch current limit (typically somewhere between 1.4 and 2 A), the output voltage will begin to drop. Additionally, the maximum output current can depend on other factors, including the ambient temperature, air flow, and heat sinking.

Dimensions
1
1
General specifications
2
1
Without included optional headers.
2
Regulator may overheat at lower input currents when VIN is much lower than VOUT. Available output current is a function of VIN, VOUT, and the regulator efficiency.


Check price and availability


Found 11 years, 5 months ago



Related Products


RMRC 5V Step-Up Voltage Regulator

View
RMRC 5V Step-Up Voltage Regulator

Pololu 12V Step-Up Voltage Regulator U3V12F12

View
Pololu 12V Step-Up Voltage Regulator U3V12F12

RMRC 5V/12V Dual Step Down Regulator

View
RMRC 5V/12V Dual Step Down Regulator

2A Micro-Stepping Stepper Motor Driver A4988 ( Pololu ...

View
2A Micro-Stepping Stepper Motor Driver A4988 ( Pololu Compatible )

Two LED PCB Strobe Green and Continuous White ...

View
Two LED PCB Strobe Green and Continuous White 3.3~5.5V
BevRC DPCAV Hobby-Lobby HobbyKing LowPriceRC ngHobbies NitroTek R2Hobbies RangeVideo RCTimer ReadyMadeRC HobbyWireless RCPlanet HorizonHobby HiModel OFM GetFPV AMainHobbies SDSHobby GoodLuckBuy Flying-Hobby