HiModel
FRSKY 2.4G 8-CHANNEL FUTABA FASST COMPATIBLE TF RECEIVER TFR8-S (PARALLEL CONNECTION CAPABLE)
| Model | TFR8-S |
| Weight | 14.9g |
| Dimension | 54*30*15mm |
| Operating Voltage Range | 4.0V-10.0V |
| Latency | 14ms (FS) |
, , , , , , Specifications:, , , , , , , , , , , Number of Channels: 8, 7ms (HS), , ,
Features: THIS IS THE FRSKY FASST 8-CH RECEIVER TFR8-S (SUPER ...5 Reviews
HiModel
FRSKY 2.4G FUTABA COMPATIBLE RF MODULE (TWO-WAY) & RECEIVERS COMBO DFT/V8FR
| Operating Voltage Range | 4.8V-6V |
| Operating Current | 30mA |
| Specified Range | 1.2km |
| Resolution | 10bit |
| Latency | 22ms |
| Number of Channels | 8CH |
| Dimensions | 60×37×21 mm |
| Model | DFT, two-way telemetry module |
| Operating Voltage Range | 6.0V-13.0V |
| Operating Current | 50mA |
| Output Power | 60mW |
| Resolution | 11bit (3072) |
| Futaba | 3PM, 3PK, 7U, 8U, 8J, 9C, 9Z, 10C, FN series, T10C, FC-18, FC-28. |
| Hitec | Optic 6, Eclipse 7, Prism 7. |
| WFLY | WFT09, WFT08. |
, , , , , , Specifications:, , , , , , , , , , , Receiver specifications:, Transmitter module specifications:, Compatible with the following transmitters:, , ,
Features: ◆ Advanced Continuous Channel Shifting Technology ( ACCST SYSTEM) ...4 Reviews
HiModel
FRSKY TWO-WAY 2.4G 8-CHANNEL RECEIVER D8R-II PLUS
| Model | D8R-II plus |
| Weight | 16.2g |
| Dimension | 54*27*17mm |
| Operating Voltage Range | 4.0V-7.2V |
| Operating Current | 100mA |
| Specified Range | 1.5km (Ground Range) |
| Resolution | 11bit (3072) |
| Latency | 22ms |
| Number of Channels | 8CH |
| Analog voltage | 0~3.3V |
, , , , , , Specifications:, , , , , , , , , , , Receiver specifications:, Compatible with FrSky Two Way module DFT/DJT., (V8 receivers work with DFT/DJT, just in receive-only mode.), , ,
Features: THIS IS THE NEW D8R-II PLUS VERSION. Features a) ...2 Reviews
HiModel
FRSKY 2.4G 6-CHANNEL TWO WAY COMMUNICATION RECEIVER D6FR
| Compatible with FrSky two way telemetry modules | DFT, DJT, DHT, DHT-U |
| Dimension | 42*22*11mm |
| Weight | 7.1g |
| Operating Voltage Range | 4.0V-10.0V |
| Operating Current | 50mA |
| Specified Range | 1.5km |
| Resolution | 3072 (>11bit) |
| Frame Rate | 18ms (FS) |
| Please kindly follow the steps below to perform range check | (Note |
, , , , , , Specifications:, , , , , , , , , , , 1.1 Compatibility:, 1.2 Specification:, 9ms (HS), Setup, 2.1 Bind procedure:, 1) Turn your transmitter on and switch it to PPM mode (if not set). Turn your transmitter off., 2)Turn your transmitter on while holding the F/S button on the transmitter module (Please make sure that both switches on the transmitter module are OFF in two way mode) Release it in a few seconds. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind to the receiver., 3) Connect battery to the receiver while holding the F/S button on the receiver. The LED on the receiver will flash, indicating the binding process is completed., 4) Turn on the transmitter and connect battery to the receiver. The Green LED on the receiver will indicate the receiver is receiving commands from the transmitter., 2.2 Range check:, It is highly suggested to perform pre-flight range check. Caution must be paid when you perform range check in environment with metal fences, concrete buildings, or rows of trees. Loss of signal may be experienced from reflections., 1) Place the model at least two feet (60cm) above non-metal contaminated ground (like wooden bench)., 2) Place the receiver’s antennas apart. Do not let the antennas touch the ground., 3) Place the antenna of the transmitter in a vertical position., 4) Turn on the transmitter and receiver, press the F/S button of the transmitter for 4 seconds to enter range check mode, the RED LED of the transmitter module will be off, GREEN LED will flash rapidly, the BEEPER will sound. The effective distance will be decreased to 1/30 of full range., 5) Walk away from the model whi,
Features: Features: 1) Lighter in weight and smaller in dimension. ...HiModel
FRSKY AMPERE SENSOR FAS-100
| Model | FAS-100 |
| Dimension | 38 x 30 x 10mm |
| Weight | 24g |
| Measurement range | 0-100A |
| Maximum safe current | 100A |
| Sensor current consumption | 33mA |
| Update rate | ≥1Hz |
, , , , , , Specifications:, , , , , , , , , , , * When use the amp sensor FAS-100 with a sensor hub, please make sure your sensor hub firmware is V2.0., , ,
Includes/Requires: Includes:1 x amp sensorHiModel
FRSKY 40A AMPERE SENSOR FAS-40
| Model | FAS-140 |
| Dimension | 31.5x24.5x5mm |
| Weight | 9.7g |
| Measurement range | 0~40A |
| Maximum safe current | 40A |
| Sensor current consumption | 20mA |
| Update Rate | ≥1Hz |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: FAS-40 can be connected to FrSky Sensor Hub or ...HiModel
FRSKY TWO-WAY 2.4G FUTABA COMPATIBLE RADIO SYSTEM TELEMETRY DFT/D8R-II PLUS
| Model | DFT |
| Operating Voltage Range | 6.0V-13.0V |
| Operating Current | 50mA |
| Output Power | 60mW |
| Resolution | 11bit (3072) |
| Futaba | 3PM, 3PK, 7U, 8U, 8J, 9C, 9Z, 10C, FN series, T10C, FC-18, FC-28. |
| Hitec | Optic 6, Eclipse 7, Prism 7. |
| WFLY | WFT09, WFT08. |
| Model | D8R-II Plus |
| Weight | 16.2g |
| Dimension | 54*27*17mm |
| Operating Voltage Range | 4.0V-7.2V |
| Operating Current | 100mA |
| Specified Range | 1.5km (Ground Range) |
| Resolution | 11bit (3072) |
| Latency | 22ms |
| Number of Channels | 8CH |
| Analog voltage | 0~3.3V |
, , , , , , Specifications:, , , , , , , , , , , Transmitter module specifications:, Compatible with the following transmitters:, Receiver specifications:, , ,
Features: The Two-way Radio System developed by FrSky provides an ...2 Reviews
HiModel
FRSKY 2.4G 8-CHANNEL RECEIVER W/PPM OUTPUT V8R7SP
| Model | V8R7-SP |
| Operating Voltage Range | 3.0V-16.0V |
| Operating Current | 30mA |
| Resolution | 3072 |
| Latency | 22ms |
| Specified | 7CH, 9g, 49mm×23mm×12mm, 1.5km-2.5km |
| Warning | DO NOT connect servos to channel 8, otherwise servos will get hot or even burn out. |
, , , , , , Specifications:, , , , , , , , , , , V8R7-SP improves the smoothness of high-speed digital servos., Bind Procedure:, 1) Turn on your transmitter and switch it to PPM mode, turn off the TX., 2) Turn on your transmitter while holding the programming button. Release it a few seconds later. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver., 3) Connect the battery to the receiver while holding the receiver’s F/S button. The LED on the receiver will flash, indicating the binding process is complete. Turn off the transmitter and receiver., 4) Turn on your transmitter. Connect the battery to the receiver when ORANGE LED on TX is on. The LED on the receiver will indicate the receiver is receiving commands from the transmitter. In a few seconds system is ready to work (communication is established)., Binding is required only to set up a new link (like new or additional receiver or transmitter module). To control multi-receivers, every receiver should be programmed with the transmitter in binding state., Failsafe:, V8R7-SP supports failsafe function for all channels. Just do it as bellow:, After the receiver has been bind, press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, the failsafe is set up successfully., If you do not need the failsafe function any more, just re-bind the receiver., , ,
Includes/Requires: Includes:1 x V8R7SP receiverHiModel
FRSKY TWO-WAY 2.4G JR COMPATIBLE RADIO SYSTEM TELEMETRY DJT/D8R-II V2
| Model | DJT |
| Operating Voltage Range | 6.0V-13.0V |
| Operating Current | 50mA |
| Output Power | 60mW |
| Resolution | 11bit (3072) |
| Model | D8R |
| Weight | 16.2g |
| Dimension | 54*27*17mm |
| Operating Voltage Range | 4.0V-7.2V |
| Operating Current | 100mA |
| Specified Range | 1.5km (Ground Range) |
| Resolution | 11bit (3072) |
| Latency | 22ms |
| Number of Channels | 8CH |
| Analog voltage | 0~3.3V |
, , , , , , Specifications:, , , , , , , , , , , Transmitter module specifications:, Compatible with the following transmitters:, JR: 347/388/783/U8/PCM10/PCM10S/PCM10SX/, PCM10IIS/8103/J9303/MX-22/MX-24S/PX/9XII., Receiver specifications:, , ,
Features: The Two-way Radio System developed by FrSky provides an ...2 Reviews
HiModel
FRSKY LCD DISPLAY FLD-02 (UPGRADING VERSION FOR FLD-01)
| Model | FLD-02 |
| Compatibility | FrSky DFT, DJT and DHT |
| Dimension | 55*40*12mm |
| Pixel | 128*64 |
, , , , , , Specifications:, , , , , , , , , , , Compatibility:, Installation:, Connect FrSky LCD-fdd_lite to the four pins on FrSky telemetry module (Rxd, Txd, +5V, GND) by the provided cable. Confirm the orientation is correct and make sure both switches on telemetry module are OFF., , ,
Features: Features 1) Show all connected sensors data; 2) Capable ...HiModel
FRSKY 2.4G 8-CHANNEL FUTABA FASST COMPATIBLE TF RECEIVER W/RSSI & SB PORTSTFR8SB
| Model | TFR8SB (8ch FASST compatible receiver with RSSI & SB ports) |
| Weight | 11.5g |
| Dimension | 44.5x 27.5 x 17mm |
| Operating Voltage Range | 3.5V-10.0V |
| Servo Frame rate | 14ms (FS - normal speed mode) |
, , , , , , Specifications:, , , , , , , , , , , Number of Channels: 8, 7ms (HS - high speed mode), , ,
Features: THIS IS THE FRSKY FASST 8-CH RECEIVER TFR8SB VERSION. ...HiModel
NGH GF38 38CC 4-STROKE PETROL ENGINE |
| Type | 4-stroke Air cooled Gasoline Engine for Model Airplane Use Only |
| Displacement | 37.97cc |
| Bore*Stroke (mm) | 39*31.8 |
| Carburetor | Walbro custom WT1022 |
| RPM range | 1800-8000rpm |
| Spark plug type | CM-6 |
| Recommended propellers | 18*10, 19*8, 19*10, 20*8 |
| Weight | 1310g |
, , , , , , Specifications:, , , , , , , , , , , Compression ratio: 9, Break in fuel oil ratio: 25:1, General use fuel oil ratio: 35:1, , ,
Features: This is the new NGH GF38cc 4-stroke gasoline engine. ...4 Reviews
HiModel
SPRINGRC 2.4GHZ 6-CHANNEL MINI RECEIVER RG661A
| Channel number | 6 channels |
, , , , , , Specifications:, , , , , , , , , , , Receiver type：RG661A (the receiver using same sticker on top as RG661, but with an additional sticker on the back indicating "Model: SM-RG661A"., Voltage：4.8--6V, Weight：6g, Size：34*20*14mm, Antenna length：14cm, Note: The receiver GR661A does not compatible with previous old version transmitter TG661, and only compatible with the latest version TG661A., , ,
Features: This receiver only work with transmitter SPRINGRC 2.4Ghz 6-Channel ...HiModel
XERUN-60A BRUSHLESS ESC FOR 1/10 CAR/TRUCK (BLUE SPIRIT EDITION)
| Model | XERUN-60A-V2 |
| Cont./ Burst Current | 60A/360A |
| Resistance | 0.0006 ohm |
| Suitable Car | 1/10, 1/12 on-road & off-road, 1/8, 1/10 scale rock crawler |
| Suite motors | Sensored and sensorless Brushless Motors |
| Battery | 4-9 cells NiMH or 2-3 cells Li-Po |
| BEC Output | 5.75V@3A Built-in BEC |
| Dimension | 43mm(L) * 36mm(W) * 33mm(H) |
| Weight | 80g |
| Fan Working Voltage | 5V@0.16A, maximum 8V. (The fan gets the power supply directly from the battery) |
, , , , , , Specifications:, , , , , , , , , , , 5-6 NIMH or 2 Lipo ≥5.5T(on-road), ≥Suitable 8.5T(off-road), 8-9 NIMH or 3 Lipo ≥10.5T(on-road), ≥17.5T(off-road), , ,
Features: 【FEATURES】 ► Compatible with all sensorless brushless motors and ...HiModel
XERUN-120A-V2 BRUSHLESS ESC FOR 1/10 CAR/TRUCK (BLUE SPIRIT EDITION)
| Model | XERUN-120A-V2 |
| Cont./ Burst Current | 120A / 760A |
| Resistance | 0.0003 ohm |
| Suitable Car | 1/10, 1/12 on-road & off-road, 1/8, 1/10 scale rock crawler |
| Suite motor | Sensored and sensorless Brushless Motors |
| Battery | 4-9 cells NiMH or 2-3 cells Li-Po |
| BEC Output | 5.75V@3A Built-in BEC |
| Dimension | 43mm(L) * 36mm(W) * 33mm(H) |
| Fan Working Voltage | 5V@0.16A, maximum 8V. (The fan gets the power supply directly from the battery) |
, , , , , , Specifications:, , , , , , , , , , , 5-6 NIMH or 2 Lipo ≥3.5T(on-road), ≥5.5T(off-road), 8-9 NIMH or 3 Lipo ≥5.5T( on-road), ≥8.5T(off-road), Weight 105g, , ,
Features: 【FEATURES】 ► Compatible with all sensorless brushless motors and ...