Flying-Hobby
LONG FULL SERVO ARM - FUTABA / ALIGN (SLIVER)
Product Detail :, Heavy duty machined alloy servo arm provides positive flex free control and a high degree of structural security.,
All holes drilled and threaded to accept M2 fixings and ...Flying-Hobby
FUTABA BLS172SV SBUS2 HV ULTRA TORQ PROGRAMMABLE SERVO
| Torque | 514 oz-in (37 kg-cm) @ 7.4V |
| Speed | 0.11 sec/60° @ 7.4V |
| Dimensions | 1-9/16 x 13/16 x 1-1/2" (41 x 21 x 38mm) |
| Weight | 2.6 oz (74 g) |
FEATURES:, Brushless motor offers incredible holding power and 5X longer life than servos equipped with brushed motors Ultra high torque Handles up to 2S LiPo power Programmable and compatible with S.Bus and S.Bus2 Dual ball bearing supported output shaft Aluminum center case One year limited warranty through Hobby Services beginning at date of purchase, INCLUDES:, HV BLS172SV UHT S.Bus2 Servo with Instructions 0.83" (21mm) Round Horn 1.8" (45mm) Round Horn 1.5" (39mm) Four Point Horn 1.2" (32mm) Six Point Horn Four each, Grommets, Eyelets and Mounting Screws, SPECS:,
Flying-Hobby
FUTABA R2008SB 8-CH 2.4GHZ S-FHSS RECEIVER (FOR AIRPLANE TX)
| • Modes | S-FHSS or FHSS |
| • Voltage Input | 4.8V-7.4V battery or regulated output from ESC |
| • Compatible Batteries | NiCd, NiMH, LiPo, LiIon or LiFe |
| • Dimensions | 0.98 x 1.69 x 0.55 in (24.9 x 42.8 x 14.0 mm) |
| • Weight | 0.34 oz (9.5 g) |
Product description :, , :, • For aircraft models, :, :, • R2008SB 2.4GHz S.Bus S-FHSS 8 Channel Receiver with Instruction Sheet,
Features • Dual Antenna Diversity • High voltage operation (4.8 ...Flying-Hobby
FUTABA DIGITAL SERVO S9650
| Control System | +Pulse Width Control 1520usec Neutral |
| Required Pulse | 3-5 Volt Peak to Peak Square Wave |
| Operating Voltage | 4.8-6.0 Volts |
| Operating Temperature Range | -20 to +60 Degree C |
| Operating Speed (4.8V) | 0.14sec/60 degrees at no load |
| Operating Speed (6.0V) | 0.11sec/60 degrees at no load |
| Stall Torque (4.8V) | 50 oz/in. (3.6kg.cm) |
| Stall Torque (6.0V) | 62.5 oz/in. (4.5kg.cm) |
| Operating Angle | 45 Deg. one side pulse traveling 400usec |
| 360 Modifiable | Yes |
| Direction | Counter Clockwise/Pulse Traveling 1520-1900usec |
| Motor Type | Coreless Motor |
| Potentiometer Drive | Indirect Drive |
| Bearing Type | Dual Ball Bearings |
| Gear Type | All Nylon Gears |
| Connector Wire Length | 12" |
| Dimensions | (43 x 15 x 28.6mm) |
| Weight | .92oz. (26g) |
Flying-Hobby
ALUMINUM RADIO STAND (BLUE)
Specifications:, Fit with Futaba 9C series and JR 9X series.,
Flying-Hobby
SAVOX SC-1258TG STANDARD DIGITAL "HIGH SPEED" SERVO
| Speed @ 6.0V | 0.08 sec/60° |
| Weight | 52.4g |
| Bearing | Dual |
| Type | Standard |
| Case | Aluminum Heatsink |
| Output Shaft | 25T Spline (Futaba) |
| Case Size (LxWxH) | 40.3x20x37.2mm |
Features:, Light weight, Specifications:, , Torque @ 6.0V:, 166 oz-in / 12 kg-cm, Gear:, Titanium and Aluminum,
This is the Savox SC-1258TG Standard Size Coreless Digital High ...Flying-Hobby
SAVOX SC-1268SG DIGITAL SERVO
| Voltage Range | 4.5v-7.4v |
| Weight | 62g |
| Motor | Coreless |
| Gear | Steel |
| Case | Aluminum Heatsink |
| Output Shaft | 25T Spline (Futaba) |
| Dimensions (LxWxH) | 40.3x20.2x37.2mm |
Features:, , Specifications:, , Torque:, @6.0v - 208 oz-in. (13 kg-cm) / @7.4v - 361oz-in. (26 kg-cm), Speed:, @6.0v - 0.13sec/60° / @7.4v - 0.11sec/60°,
This is the Savox SC-1268MG High Voltage Ultra Torque Digital ...Flying-Hobby
MIKADO LOGO 600 3D ELECTRIC HELICOPTER KIT - FBL OPTIONS
| Specifications | - Motor mount |
| - Rotor diameter | 1250mm to 1450mm |
| - Rotor blades | 600/620/650mm |
| - Main gear ratio | 8,1 |
| - Weight | 3,2 kg and up |
| - Battery | 6S to 10S LiPoly |
| pinion | MIK4412 12 tooth |
| Cyclic servos | FutabaBLS 451 or JR 8717 or BLS 253 |
| Tail Servo | Futaba BLS 251 or JR 8900G |
| ESC | Kontronics Jive80HV or Casle Creations Ice 80 HV |
| Battery | 10cell 5000MAH |
Super light, extremely rigid mainframe:, The mainframe consists of a right and a left frame made from glassfiber-reinforced polymer. A number of components which are usually separate parts are fully integrated into this frame, and do not have to be bought separately, for example bearing case, battery tray and servo mounting plate. There is ample space for any brand of available battery. The mainframe offers enough room for motors of up to 56 mm in diameter., Herringbone main gear:, Experience of previous years shows that conventional gear trains have reached their limit with regard to performance. The increasing power made available by latest Lipoly batteries calls for new concepts. We are proud to present this new gear technology, which includes herringbone gears. This type of gear has never before been used in a model helicopter., Its main advantages are:, - Considerably more transmission efficiency - Very smooth running - Extremely low noise level, Suggested Kit Combination:, , motor:, Scorpion HK-4035-560, Note:, Mikado LOGO kits do not come with a pinion, tail blades, or main blades. You must choose your own pinion that matches your motor to obtain the headspeed that you desire. Please use our headspeed calculator if you need help figuring out what pinion you need!,
This is the Logo 600 V-Bar Flybarless version kit. We’ve ...Flying-Hobby
JR TX NECKSTRAP BALANCER B3
Best For :, Futaba / 6EXH / 6EXH 2.4GHz / 7C / 7C 2.4GHz / 9C / 12GF / 12GF 2.4GHz / 14MZ / 14MZ 2.4GHz,
JR9XII / JR DSX9 DSM2 2.4GHz / JR 10X PCM ...Flying-Hobby
MIKADO LOGO 600SE ELECTRIC HELICOPTER KIT - FBL OPTIONS
| Specifications | - Motor mount |
| - Rotor Blades | 600mm to 690mm |
| - Main gear ratio | 8,1 |
| - Weight | 3,2 kg and up |
| - Battery | 8S to 10S LiPoly |
| pinion | MIK4411 11 tooth |
| Cyclic servos | FutabaBLS 451 or JR 8717 or BLS 253 |
| Tail Servo | Futaba BLS 251 or JR 8900G |
| ESC | Kontronics Jive120HV or Casle Creations Ice 160 HV |
| Battery | 10cells or 12cells 5000MAH |
Superlight, extremely rigid mainframe:, The mainframe consists of a right and a left frame made from glassfiber-reinforced polymer. A number of components which are usually separate parts are fully integrated into this frame, and do not have to be bought separately, for example bearing case, battery tray and servo mounting plate. There is ample space for any brand of available battery. The mainframe offers enough room for motors of up to 56 mm in diameter., Herringbone main gear:, Experience of previous years shows that conventional gear trains have reached their limit with regard to performance. The increasing power made available by latest Lipoly batteries calls for new concepts. We are proud to present this new gear technology, which includes herringbone gears. This type of gear has never before been used in a model helicopter., The main advantages of the new Herringbone gear design are:, - Considerably more transmission efficiency, Very smooth running, Extremely low noise level, Suggested Kit Combination:, , motor:, Scorpion HK-4035-560(10cell) or xera-4030-560 (10cells), Note:, Mikado LOGO kits do not come with a pinion, tail blades, or main blades. You must choose your own pinion that matches your motor to obtain the headspeed that you desire. Please use our headspeed calculator if you need help figuring out what pinion you need!,
This is the Logo 600SE V-Bar Flybarless version kit. The ...Flying-Hobby
T-REX 500PRO DFC JR XG8 RTF COMBO (DFC VERSION)
| ●Operating Temperature | -10~60 degree |
| ●X and Y axis Operating Angle Range | -300~+300 degree |
| ●Z axis Operating Angle Range | -600~+600 degree |
| ●Size | 36.5x25.2x15.6 mm Size |
| ●Maximum working voltage | 8.5V |
| ● Length | 868mm |
| ● Height | 275mm |
| ● Main Blade Length | 425mm |
| ● Main Rotor Diameter | 978mm |
| ● Tail Rotor Diameter | 206mm |
| ● Motor Drive Gear | 12T |
| ● Main Drive Gear | 134T |
| ● Autorotation Tail Drive Gear | 145T |
| ● Tail Drive Gear | 36T |
| ● Weight(With Motor) | 1210g |
Remark :, All T-REX 500 DFC Combo have change to this canopy -, Combo Included :, ●T-REX 500PRO DFC Kits Set X1, Instruction(3GX Programmable Flybarless System) :, ●Brand new redesigned 3GX represents a new generation of multi function flybarless system. The dramatically improved performance will create immediate impact on any enthusiasts., 3GX Programmable Flybarless System :, Specification(T-REX 500 PRO DFC) :, ●Features, Specification(T-REX 500 PRO DFC) :, ● Drive Gear Ratio: 1:11.17:4.03,
HC5112 ●3GX Flybarless System X1 set ●425 3G Carbon fiber ...Flying-Hobby
D6EF METAL SERVO HORN
FUTABA Servo ..." />
| Specification | ●Quantity |
Instruction:, ●6061-T6 Aluminum alloy material and CNC processed。,
●Use For ALIGN DS5ˋDS6 Digital Servo ●Use For FUTABA Servo ...