RCPlanet
KYOSHO O-RING SET KYOIFW140-05
, ,
Made from high grade soft silicone rubber, these o-rings have ...RCPlanet
KYOSHO UNIVERSAL SWING SHAFTS 62.5MM RB5 SP - PACKAGE OF 2 KYOUM522
, ,
Check the set screw for the CVD pin to make ...RCPlanet
KYOSHO MR-02MM R/S MCLAREN F1 GTR NO.44 KYO30489LA-B
, ,
Low center of gravity and high agility are the trademarks ...RCPlanet
KYOSHO MINI INFERNO 2 TYPE 5 1/18 RTR BUGGY KYO30125T5B
, ,
Competition-level buggy performance has been packed into a 1/18-size electric-powered ...RCPlanet
KYOSHO MA-010 W/O TX WITH ASF BCS FORMULA D RX-7 BODY KYO30578ZKM-B
, ,
In the world of drift racing, MAZDA's rotary engine powered ...RCPlanet
KYOSHO SPRING SHORT INFERNO WHITE MP-5 KYOIFW32W
, ,
Originally made for the MP 7.5 series of buggies including ...RCPlanet
KYOSHO ALUM REAR HUB 2MM OFFSET MP9 KYOIFW414
, ,
Beautifully machined from 7075 billet and finished with a hard ...RCPlanet
KYOSHO 84MM UNIVERSAL SWING SHAFT SET KYOUMW601
, ,
Replaces the stock dog bone and axle setup of the ...RCPlanet
KYOSHO SILICONE OIL #5000 KYOSIL5000
, ,
FEATURES: Silicone Oil Will Not Thicken or Thin in Different ...RCPlanet
KYOSHO HUB CARRIER 20 DEGREES MP777 KYOIF304B
, ,
Use these for a bit more aggressive and fast steering ...RCPlanet
KYOSHO HARD SPRING SERVO SAVER SET KYOIFW338
, ,
The original servo saver that shipped with the STR kit ...RCPlanet
JCONCEPTS ILLUZION KYOSHO RT5 HI FLOW BODY JCI0099
, ,
JConcepts Illuzion Hi-Flow styling presents a flowing design while incorporating ...HiModel
KYOSHO GXR-15 ENGINE W/RECOIL STARTER FOR CARS
| Displacement | 19.96cc |
| RPM range | 3,000-19,000(r.p.m) |
| Output | 0.58/16,000(kw/r.p.m) |
| Weight | 227g |
| ① Needle value | 2 and 1/2 turns unscrewed from closed position. |
| (Caution | after each tank, allow the engine to cool off naturally!) |
, , , , , , Specifications:, , , , , , , , , , , * Note: As this engine is produced as OEM from ASP for Koyosho, the outer box you receive may with ASP marks, this is not a mistake., ● Engine starting & break-in, Adjust the needle valve and air/fuel mixture adjustment screw to their standard position as follows:, ② Air/fuel mixture adjustment: Gently screw in the idle mixture screw to closed position (clockwise); 2 and 1/2 turns unscrewed from closed position (counter clockwise), Adjustments ① ~ ② may slightly vary according to the type of glow plug and glow fuel., Proceed as follows when starting and breaking the engine in:, 1. Make sure the needle valve is unscrewed 2-1/2 turns from closed position., 2. Fill fuel into the tank. Move the throttle lever to the high position, prime the engine (push the choke button 2 to 3 times or put 2 to 3 drops of fuel directly into the carburetor) and move the throttle lever back to the slow throttle position., 3. Attach the booster cord or one-touch glow plug heater to the engine in order to electrify the glow plug., 4. Quickly pull the recoil starter rope (starter knob) several times. Only pull out 20 to 30cm of cord., (Caution: be careful not to pull out more than 50cm of cord because you may tear it and the spring inside the recoil starter!), 5. Once the engine is started, wait 5 to 10 seconds before detaching the booster cord or one-touch glow plug heater., 6. Run the engine another 2 to 3 tanks and make sure you do not apply full throttle. Also afterwards, do not increase RPM abruptly! Tighten the needle valve by 1/8 turns and continue to run the engine, handling it gently., 7. During the break-in, adjust the idle rpm with the throttle valve adjustment screw.. If rotating it clockwise (right), idle rpm increase. Idle rpm are halfway between rpm when the clutch engages and rpm when,
Includes/Requires: Includes:1 x engine 1 x manual (multi-language, including English) ...8 Reviews