ReadyMadeRC
TAROT 2 AXIS CAMERA GIMBAL FOR GOPRO HERO3, 3+ W/FREE CABLE
| 7. Supported receiver type | conventional/S-BUS/DSM2/DSMJ/DSMX receiver. |
| 8. Supported RC | PPM/PCM/2.4G. |
| 9. Operating supply | DC 7.4V~14.8V (Li-Po 3S is recommended) |
| 10. Operating current | 200mA-500mA (Depending on power supply voltage and motor power) |
| 11. Operating temperature | -15ºC~65ºC. |
| 12. CPU | Double 32bit ARM |
| 13. Sensor technology | 3-axis MEMS gyro and accelerometer. |
| 14. Max angular rate | 2000 º /sec. |
| 15. Max acceleration | 16g. |
| 16. Control frequency | 2000Hz |
| 17. Motor driver frequency | 20KHz (quiet and smooth) |
| 18. Control accuracy | 0.1° |
| 19. Control range | -45º~45º(roll), -135 º~90 º(tilt). |
| 20. Attitude arithmetic | BLDC gimbal dedicated brushless motor decoupled EKF algorithm. |
| 21. Aerial photography equipment | GOPRO Hero3. |
Note:, Modifications may be required to use HERO4, Parts included for the kit: 2 motors mounted onto the swing arms, gimbal controller board, mounting bracket with GoPro brace, 2 male to male servo cables (one with Y end), USB firmware updater connector and cable, 4 rubber dampeners and mounting bracket + hardware for the gimbal.,
FREE LIVE VIDEO OUT CABLE OPTION...YES, OUR CABLES WILL WORK ...ReadyMadeRC
DJI CAN BUS HUB - 4 PORT EXPANSION HUB
,
Used for connecting DJI Naza or A2 with other DJI ...ReadyMadeRC
IMMERSIONRC - RF POWER METER
,
A unique device, introduced to allow the modeling community to ...ReadyMadeRC
SASQUATCH LABS / HOVERTHINGS FLIP FPV
Included in each build:,
Pre-flown and tested individually, the Team Sasquatch Flip FPV Quads ...ReadyMadeRC
PROTECTIVE ADJUSTABLE MOUNT - DJI NAZA GPS - GREEN - 3D SHELLZ
Provides two critical functions:,
A custom 3d printed mount for your DJI NAZA gps/compass ...ReadyMadeRC
AIR TITAN KIT (HARDWARE INCLUDED) NO ELECTRONICS
| ATTENTION | According to |
| Wingspan | 2520MM/ 99.2inch |
| Kits Airplane weight | 2.4kg(5.3IB) including all reinforcement parts |
| Extra Payload | 3.0kg-4.0kg (6.6IB-8.8IB)/ flight weight>6.0kg |
| Customized Motor for Airtitan | M60K/ Power 1500W |
| Testing static thrust | 5.5-6.0kg (6S, 15" Prop) |
| Propeller recommend | 15*6 / 15*7 |
| ESC | Advanced 80A OPTO (without Built-in BEC) |
| External UBEC | 5V/6A,5.5V/6A or 6V/6A (Switchable) |
| Material of fuselage and Wing | EPO |
| RMRC 6s batteries found here | 10,000 mAh |
| Main-wing | built- in 4PCS alloy aluminum plus 2PCS carbon tube through the Main-wing |
| Control surface of Aileron and Elevator | carbon tube reinforced, no need further DIY |
Breakdown for Transport:, This plane carries over the “gentle stall” characteristics of the Penguin, but super sized. No scary tip-stalls. Instead, it has super predictable flight characteristics. Tricycle landing gear with a steerable nose gear is included, along with a stable high wing design, plus a bottom camera port, and secondary top camera mounting area. The ARF version includes an 80A OPTO ESC, Massive 1500W motor, a switch mode 5-6V adjustable UBEC, and heavy duty metal geared servos for the ailerons, elevator, and steering. Hand launch is possible, but you might need to work out a bit before you try it (see beginning of video!). Like the Penguin, this airframe was designed with FPV in mind, but would also serve as a great plane to fly at the field if you just want something you can strap a GoPro to, or maybe even 10 of them since it won’t mind the weight. Available and ready to ship now at Ready Made RC, LLC, the best place to get ALL your FPV and RC equipment!, Specifications:, , Customized Brushless Power system:, Servos:, , Battery Recommendations:, , Flight Recomendations:, *Note : 5S with a 15*8 Prop is okay if your flight weight is less than 5.5kg. A 6S pack will however provide “better power", *Note: Flight weight of 5.5kg-6.0kg can meet most FPV requirements, and we recommend less than 6.0kg for most FPV pilots, High Quality Reinforcement :, , Horizontal stabilizer:,
UN1133 shipping regulations, the glue contained in t his product ...ReadyMadeRC
AIR TITAN KIT (HARDWARE INCLUDED) WITH MOTOR, ESC, AND SERVOS
| ATTENTION | According to |
| Wingspan | 2520MM/ 99.2inch |
| Kits Airplane weight | 2.4kg(5.3IB) including all reinforcement parts |
| Extra Payload | 3.0kg-4.0kg (6.6IB-8.8IB)/ flight weight>6.0kg |
| Customized Motor for Airtitan | M60K/ Power 1500W |
| Testing static thrust | 5.5-6.0kg (6S, 15" Prop) |
| Propeller recommend | 15*6 / 15*7 |
| ESC | Advanced 80A OPTO (without Built-in BEC) |
| External UBEC | 5V/6A,5.5V/6A or 6V/6A (Switchable) |
| Material of fuselage and Wing | EPO |
| RMRC 6s batteries found here | 10,000 mAh |
| Main-wing | built- in 4PCS alloy aluminum plus 2PCS carbon tube through the Main-wing |
| Control surface of Aileron and Elevator | carbon tube reinforced, no need further DIY |
Breakdown for Transport:, This plane carries over the “gentle stall” characteristics of the Penguin, but super sized. No scary tip-stalls. Instead, it has super predictable flight characteristics. Tricycle landing gear with a steerable nose gear is included, along with a stable high wing design, plus a bottom camera port, and secondary top camera mounting area. The ARF version includes an 80A OPTO ESC, Massive 1500W motor, a switch mode 5-6V adjustable UBEC, and heavy duty metal geared servos for the ailerons, elevator, and steering. Hand launch is possible, but you might need to work out a bit before you try it (see beginning of video!). Like the Penguin, this airframe was designed with FPV in mind, but would also serve as a great plane to fly at the field if you just want something you can strap a GoPro to, or maybe even 10 of them since it won’t mind the weight. Available and ready to ship now at Ready Made RC, LLC, the best place to get ALL your FPV and RC equipment!, Specifications:, , Customized Brushless Power system:, Servos:, , Battery Recommendations:, , Sample Battery Setup:, , Flight Recomendations:, *Note : 5S with a 15*8 Prop is okay if your flight weight is less than 5.5kg. A 6S pack will however provide “better power", *Note: Flight weight of 5.5kg-6.0kg can meet most FPV requirements, and we recommend less than 6.0kg for most FPV pilots, High Quality Reinforcement :, ,
UN1133 shipping regulations, the glue contained in t his product ...ReadyMadeRC
GRAUPNER CAM SPEED PROP 4" X 3"
,
Overview Propeller series for electric-powered pylon racing models and other ...ReadyMadeRC
BLACKOUT MINI H QUAD FRAME
| Frame Weight | Version 1 |
| Materials | 3k Weave Carbon Fiber |
| Fasteners | Stainless Steel & Black Nylon 6/6 |
| Size | 220mm diagonally, 175mm wide, 130mm long motor-to-motor; about 1/2 the size of a regular quadcopter |
| Flight Controller Mount | 30.5mm x 30.5mm |
| Board Camera Mount | 32mm x 32mm |
| Motors | Tiger MN1806 2300kv Motor |
| Propeller | Gemfan 5x3 |
| ESC | 12-15A |
| Battery | 3S 1300mah - 1500mah |
| Flight Controller | CC3D |
| Flight Camera | CCD Camera or RMRC Pico |
| HD Camera | Mobius Action Camera |
Specifications:, , Version: 2, Maximum Propeller: 5", Motor Mount: M2 12mm - 16mm (Tiger MN1806 2300kv, RCX 1804 2400kv), M3 19mm (Tiger MT2206 2000kv, Sunnysky X2204 2300kv), Features:, , Includes:, , Helpful Information:, , Videos:,
Description The Blackout Mini H Quad is a low weight ...ReadyMadeRC
BLACKOUT MINI SPIDER HEX FRAME
| Frame Weight | 220 grams |
| Materials | 3k Twill Weave Carbon Fiber |
| Fasteners | Stainless Steel & Black Nylon 6/6 |
| Size | 290mm MTM |
| Flight Controller Mount | 30.5mm x 30.5mm & 45mm x 45mm |
| Board Camera Mount | 32mm x 32mm |
| GPS Mount | 30.5mm x 30.5mm |
| GoPro Protection | Accepts RMRC GoProtector & Eyefly GoPro 3 Carbon Fiber (or G10) case |
| Motors | Tiger MN1806 2300kv Motor |
| Propeller | GemFan 5x3 2 Blade |
| ESC | 12 - 15amp |
| Battery | 3S 3300mah 35C/70C |
| Flight Controller | RMRC CC3D |
| HD Camera | GoPro 3 |
Version: 1, Maximum Propeller: 5", Motor Mount: M2 12mm - 16mm (Tiger MN1806 2300kv, RCX 1804 2400kv), M3 19mm (Tiger MT2206 2000kv, Sunnysky X2204 2300kv),
Description The Blackout Mini Spider Hex is a low weight ...ReadyMadeRC
REPLACEMENT WHITE ARM PLATES - HONEY BADGER (2 PLATES)
,
Replacement WHITE Arm Plates - Honey Badger (2 plates plus ...ReadyMadeRC
VAS WRAITH - BASIC KIT
| ATTENTION | According to |
| Range | 9 miles round trip |
| Flight time | 12-20 minutes |
| Top Speed | 75mph |
| Recommended motor | 1600-1800 kV, 150-250 Watts |
| Recommended Battery | 3S 4000 – 3S 5000 mAh Lipo (or 4S 3000 with 1400 kV motor) |
| Build time | 4-6 hours |
Wraith:, , Recommended prop size: 7”, What’s included in the kits:,
UN1133 shipping regulations, the glue contained in t his product ...ReadyMadeRC
RMRC 6A POWER REGULATOR - 5 TO 6 VOLT (UBEC)
| Output | 5v or 6v(Selectable via jumper) 6A continuous, 8A burst |
| Input | 7v-25.5v (2-6S Lipo) |
| Size | 50x22x5 mm |
| Weight | 15g |
Specifications:,
High quality Ready Made RC, LLC 6A UBEC w/ Noise ...ReadyMadeRC
GRAUPNER CAM SPEED PROP 4.7" X 4.7"
,
Overview Propeller series for electric-powered pylon racing models and other ...ReadyMadeRC
GRAUPNER CAM SPEED PROP 5.5" X 5.5"
,
Overview Propeller series for electric-powered pylon racing models and other ...