HobbyKing
HEAVY DUTY RX TWIN SWITCH WITH CHARGE PORT & FUEL DOT RED
| Max Voltage | 18v |
| Wire | AWG 22 Silicone |
| Dimensions | 78mmx24mm |
| Connectors | Generic JR/Futaba |
Specs:, Max Amps:5A, Weight:, 36g With Wires & Connectors,
Heavy Duty Reciever & Ignition or Twin RX Battery Switch ...5 Reviews
HobbyKing
HEAVY DUTY RX SWITCH WITH CHARGE PORT & FUEL DOT RED
| Max Voltage | 18v |
| Wire | AWG 22 Silicone |
| Dimensions | 63mmx24mm |
| Connectors | Generic JR/Futaba |
Specs:, Max Amps:5A, Weight:, 20g With Wires & Connectors,
Heavy Duty Reciever Battery Switch made from GFPA with charge ...5 Reviews
HobbyKing
BA-4-IN-1CX MIXERBOARD (72MHZ SINGLE CONVERSION)
| Main ESC Output Current | 5A (Min.)/15A (Max.) |
| Tail ESC Output Current | 5A (Min.)/15A (Max.) |
| 5V Max. Output (BEC) Current | 1.5A |
| Receiver system | FM PPM |
| Effective receiving range | 200m |
| Size | 25mm*18mm*24mm |
5 Reviews
HobbyKing
HOBBYKING ADVANCED EDF JET LED LIGHTING SYSTEM
| Power | 3s or 4s |
| Max draw | 400mA |
| Weight | 81g |
Our new EDF LED lighting system adds great scale realism to your EDF Jet. This system has been designed exclusively for EDF Jets. Included in this set: Port (Red) & Starboard (Green) wing tip lights, a red clearance beacon, a super bright 10mm white landing light and an afterburner., Features:, • Authentic navigation lighting scheme, Lights:, 1 x 3mm Red LED 450mm lead, Spec:, Input:, 2 channels (Thro & Aux), Dimensions:, (control unit only) 30mm x 50mm x 11mm,
Looking to add some scale flare to your next EDF ...5 Reviews
HobbyKing
TURNIGY 1/16 4X4 MINI TROOPER SCT (ARR)
| Motor | 4800KV Brushless i |
| Servo | 15g Micro |
| Length | 245mm |
| Width | 190mm |
| Height | 120mm to top of Cab |
| Ground Clearance | 20~30mm Adjustable |
Spec:, :, 25A Brushless (with Reverse), Battery:, 2S LiPo (98x25x40mm Max Size) w/ XT-60 connector [Required], Traction:, Full Time 4WD, Twin Diff with slipper clutch on Spur gear,
The Turnigy 1/16 4WD Mini Trooper is great fun with ...5 Reviews
HobbyKing
CYCLONE-E ALL MOULDED COMPOSITE HOTLINER 2000MM (ARF)
| Span | 2000mm |
| Length | 1200mm |
| Airframe weight | 950g |
| Flying weight | 1400-1600g |
| Wing Section | RCmod |
| Esc | 100-120amp |
| Prop | 13x10 - 15x13 |
Features:, • High Precision fully moulded airframe, Spec:, Requires:, Motor:, Turnigy DT38 640kv inrunner or equivilent, Radio:, 6 or more channel computer radio, Servos:, 4 x slim wing; 2 x 10-15g mini digital metal geared, Battery:, 4s/5s - 2650-3300 mah(Max size 44mm x 30 x 250),
The Cyclone-E is an ELECTRIC 2-metre rocket ship! Not intended ...5 Reviews
HobbyKing
NTM PROP DRIVE SERIES 28-26A 1200KV / 250W (SHORT SHAFT VERSION)
| Max current | 18A |
| Shaft | 3mm |
| Weight | 57.6g |
| ESC | 20A |
| Cell count | 3s~4s Lipoly |
| Bolt holes | 16mm & 19mm |
| Note | An accessory pack is available for this motor. Please see the related items below. |
Specs:, Model:, NTM Prop Drive Series 28-26A 1200kv (short shaft version), Kv:1200rpm/v, Max Power:, 200W @ 12v (3S) / 250W @ 15v (4S), Bolt thread:M3, Connection:, 3.5mm Bullet-connector, Prop Tests:, 7x6E - 11.1v - 90W - 8A,
This is a short shaft version of our popular NTM ...5 Reviews
HobbyKing
HOBBYKING MULTI-ROTOR POWER DISTRIBUTION BOARD (DIY 8 X OUTPUT PCB)
| Power input | 8 x contact points |
| Power output | 8 x contact points |
| Dimensions | 50x50x2mm |
| Weight | 7.6g (PCB only) |
Features:, Current:, 8 x 20A outputs (MAX),
Designed in house by the HobbyKing Enginerds, this handy power ...5 Reviews
HobbyKing
PARALLEL CHARGING BOARD FOR 6 PACKS 2~6S (BARE LEADS)
| Cell | 2~6S |
| Voltage | 0~22.2VDC |
| Max current | 30A |
Battery:, 6 packs same capacity & cell count, Connector:, bare leads ready for soldering your choice of connectors,
Charge SIX (2~6S) lipo packs with same capacity & cell ...5 Reviews
HobbyKing
HOBBYKING PARALLEL CHARGING BOARD FOR 6 PACKS 2~6S (HXT4MM)
| Cell | 2~6S |
| Voltage | 0~22.2VDC |
| Max current | 30A |
| Connector | HXT4mm/jst-xh |
| Note | The batteries should have same capacity. |
Battery:, 6 packs (same capacity & cell count),
Our very own in-house designed and built parallel charge board! ...5 Reviews
HobbyKing
TURNIGY TRACKSTAR 1/10 12.0T 3300KV BRUSHLESS MOTOR
| Max Voltage | 15v |
| Max current | 35amps |
| Watts | 550 |
| Resistance | 0.0221 |
| Max RPM | 50000 |
| Length | 50mm |
| Diameter | 35.8mm |
| Shaft dia. | 3.175mm |
| Shaft length | 15mm |
| Weight | 168g |
Specs:, Kv:3300,
Trackstar 3300Kv (12.0 Turn) sensorless brushless inrunner to suit 1/10 ...5 Reviews
HobbyKing
TURNIGY TRACKSTAR 1/10 17.0T 2400KV BRUSHLESS
| Max Voltage | 21v |
| Max current | 24amps |
| Watts | 550 |
| Resistance | 0.0442Ohms |
| Max RPM | 50000 |
| Length | 50mm |
| Diameter | 35.8mm |
| Shaft dia. | 3.175mm |
| Shaft length | 15mm |
| Weight | 168g |
Specs:, Kv:2400,
Trackstar 2400Kv (17.0 Turn) sensorless brushless inrunner to suit 1/10 ...5 Reviews
HobbyKing
TURNIGY TRACKSTAR 1/10 9T 4370KV BRUSHLESS
| Max Voltage | 12v |
| Max current | 46 amps |
| Watts | 550 |
| Resistance | 0.0127Ohms |
| Max RPM | 50000 |
| Length | 50mm |
| Diameter | 35.8mm |
| Shaft dia. | 3.175mm |
| Shaft length | 15mm |
| Weight | 168g |
:, Kv:4370,
Trackstar 4370Kv (9.0 Turn) sensorless brushless inrunner to suit 1/10 ...5 Reviews
HobbyKing
MICRO 3D SINGLE AXIS THRUST VECTORING MOTOR MOUNT KIT INC. 2206 BRUSHLESS OUTRUNNER
| Motor to mount hole spacing | 32mm diagonal |
| Firewall hole spacing | 32mm diagonal |
| Standoff from firewall | 16.5mm |
| Weight | 3.1g |
| RPM/v | 1500kv |
| Dimensions | 28 x 15mm |
| Shaft | 4.0mm |
| Voltage | 7.4v~11.1v |
| Weight | 23g |
| No-load current | 1.0A @ 11.1v |
| Max Current | 10A |
| Max Watts | 95W |
| Mounting Holes | 32mm |
Mount Spec:, Motor Spec:,
Looking for something REALLY different for your 3D foamie? Check ...5 Reviews
HobbyKing
MICRO 3D SINGLE AXIS THRUST VECTORING MOTOR MOUNT KIT INC. 2204 BRUSHLESS OUTRUNNER
| Motor to mount hole spacing | 32mm diagonal |
| Firewall hole spacing | 32mm diagonal |
| Standoff from firewall | 16.5mm |
| Weight | 3.1g |
| RPM/v | 1700kv |
| Dimensions | 28 x 13mm |
| Shaft | 3.0mm |
| Voltage | 7.4v~11.1v |
| Weight | 18g |
| No-load current | 1.0A @ 11.1v |
| Max Watts | 80W |
| Mounting Holes | 32mm |
Mount Spec:, Motor Spec:, Max Current:8A,
Looking for something REALLY different for your 3D foamie? Check ...5 Reviews