GetFPV
LAYERLENS FOR GOPRO3 (V2)
For this reason, FPV Manuals developed LayerLens. LayerLens brings the most important part of the original GoPro case back: the protective lens; without adding much weight or size. Fully assembled, LayerLens for the GoPro 3 weighs only 7.5g — a small fraction the weight of the full GoPro case. LayerLens has become the standard lens protection product in the fields of RC and FPV where a GoPro is used outside of its standard housing.,
Details This is the new revision of LayerLens for the ...GetFPV
LAYERLENS REPLACEMENT VELCRO STRAP
,
Details 1 replacement velcro strap for use with fpvmanuals LayerLens. ...GetFPV
FPVMANUALS STICKER (3 PCS)
,
Details The well recognized "fpvmanuals" Sticker. Pack of 3 stickers. ...GetFPV
LAYERLENS FRONT FOR THE TEAM BLACKSHEEP ZII CAMERA CASE
,
Details LayerLens front for the TBS GoPro Cam mount for ...GetFPV
DJI WOOKONG MULTI-ROTOR AUTOPILOT
| Stop Motor | Two provided options to stop motors |
Start Motor: When using WKM, pushing throttle stick before takeoff will not start motors. You have to execute any one of following four Combination Stick Commands (CSC) to start motors.,
Details WooKong-M is a complete flight control system for all ...GetFPV
FATSHARK BASE SD VIDEO GOGGLES
| Note | Battery sold separately as this unit is typically tethered to a ground station. |
GetFPV
IBCRAZY 910MHZ BLUBEAM ULTRA
| Contains TWO antennas | 3 lobe TX, and 5 lobe RX |
| Connector type | SMA male |
GetFPV
QAV540G BRUSHLESS GIMBAL AIRFRAME (PRE-ORDER)
| Props | 11" props such as |
| Motors | We recommend the |
| ESCs | We recommend the |
Landing Gear:, You can choose between the, Gimbal Control Board:, We recommend the AlexMos board., Lipo:, A 5000mah 4s Lipo that is no wider than 51mm and no higher than 35mm (or it will not fit in the lipo compartment). We recommend HobbyKing Nano-Tech Lipos., GoPro Lens Protection:, The QAV540G gimbal requires the GoPro to be placed into the gimbal without the GoPro case. We recommend a separate, Shipping details:, When placing a pre-order, the entire order you place will be put on hold until the pre-ordered item is in stock and ready to ship. Please make a separate order for any additional items outside of the pre-order if you would like them to ship sooner, otherwise they will ship with your pre-order.,
Details The QAV540G is a high quality quad airframe that ...GetFPV
MALE JST BATTERY PIGTAIL 10CM (10PCS/BAG)
,
Details High quality silicon wire provides a higher amp output ...GetFPV
FATSHARK PREDATOR V2 VIDEO GLASSES W/TRANSMITTER AND CAMERA
,
Details The Predator V2 delivers a rewarding FPV experience for ...GetFPV
BLACK POLYAMIDE STANDOFF SET
,
Details This set is perfect for securing your flight controller ...GetFPV
IBCRAZY 910 MHZ 10DBIC CROSSHAIR ANTENNA
| Frequency range | 910 MHz |
| Size | 12"x12"x6" |
GetFPV
LC COMMON MODE POWER FILTER
| Revision | Rev3 March 2013 |
| Type | passive common-mode low-pass power ripple filter |
| Modes | common mode, single mode - jumper selectable |
| Maximum voltage | 16V DC |
| Maximum current | ~1.5A |
| Cutoff frequency at -3dB | 127 Hz (attenuates higher frequencies/noise) |
| Voltage drop over filter | 180mV at 900mA |
| Maximum voltage ripple | 120mV |
| Capacitor | Japanese Polymer Capacitor |
| Impedance/ESR | 0.012 Ohm at 100kHz/16V |
| Ripple current | 5000mA rms |
| Choke | German Common-mode Choke |
| Series resistance (DC) | 0.205 Ohm/path |
| Wire / trace thickness | twisted 22 AWG / 32 mils |
| Operating temperature | -40 °C to +105 °C |
| Dimensions | 37.7 L x 8.8 W x 14.5 H mm |
| Weight | 8.1 grams (inc. JST connectors) |
Note:, It is now possible to select between common mode and single mode filtering. A solder jumper pad on the input side disables filtering on the negative/ground-lead. If you experience issue with OSD systems, try changing the filter to single mode., Specifications:,
Details This small LC Power Filter is a must have ...GetFPV
DIN5 MULTIPLEX ADAPTER FOR AEROSIM RC FLIGHT SIMULATOR
,
Details DIN5 Multiplex trainer adapter used to connect to the ...