BevRC
CRIUS ALL IN ONE PRO FLIGHT CONTROLLER V1.0 SUPPORT MEGAPIRATENG AND MULTIWII
,
Crius All In One PRO Flight Controller V1.0 Support MegaPirateNG ...BevRC
CRIUS MWC MULTIWII SE STANDARD FOR QUAD/HEXA MINI BOARD
,
MWC is MultiWii Copter abbreviation, this open source program's original ...BevRC
BEV OSC 420-NTSC
| Pixels NTSC | 510x492, PAL |
Specifictions:, 1/3" Sony color CCD sensor.,
Industry standard composite video output. 420 TV-line resolution. Minimum Illumination ...BevRC
LIPO BATTERY PACK FOR FATSHARK GOGGLES
,
Compatible with all of the fatshark goggles, good choice for ...BevRC
RC701 5.8GHZ DIVERSITY HIGH LIGHT HD 7-INCH MONITOR
| Screen size | 7 inch |
| screen type | TFT LCD screen/long life, LED backlight |
| Resolution | 800*480 |
| Brightness | 450cd/m2 |
| contrast | 500 |
| Working Voltage | DV 7-12V(center positive) or 11.1v 3s lipo battery |
| Power consumption | < 8w |
| size | 180*120*23mm |
| Working Temp | -10--+65 degrees |
| CH1 | 5705Mhz |
| CH2 | 5685Mhz |
| CH3 | 5665Mhz |
| CH4 | 5645Mhz |
| CH5 | 5885Mhz |
| CH6 | 5905Mhz |
| CH7 | 5925Mhz |
| CH8 | 5945Mhz |
Specification:, View angle:, 140/120degree(Horizontal/Vertical), Features:, 1: Built-in Dual Receiver Automatically for best reception Automatic Antenna Swithcing, 2: Dual buffered AV output, 3: Can receive 2 different channels at the same time, 4: Not affect by 2.4Ghz R/C radios, 5: AV receiver with Diversity inputs, 6: Small, light weight, durable., Working frequencies:,
Built-in 5.8G Dual diversity receiver automatically for best reception Built-in ...BevRC
FRSKY TFRSP- FUTABA FASST COMPATIBLE WITH SPPM AND RSSI PORT
| FASST 2.4G Air Systems (7CH Mode/Multi Mode) | 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc. |
| Number of Channels | up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10) |
| Operating Voltage Range | 3.5V~10V |
| Operating Temperature Range | -10℃~60℃ |
| Dimension | 53mm*30mm*11mm |
| Weight | 13.5g |
| Note | Increased duty means good signal reception, and vice verse. |
1.1 Compatibility:, 1.2 Specifications:, Warning: Servos are not to be plugged into Channel CPPM and Channel RSSI, otherwise servos will get hot or may burn out., 2.1 Bind procedure:, Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally., 2.2 Setting failsafe:, TFRSP supports failsafe function for all channels. Follow the steps below to set failsafe:, 1) Bind the receiver first, and disable failsafe on the transmitter side;, Warning: Some transmitter manufacturers use a failsafe method that can interfere with that used by FrSky. Be sure to disable any transmitter failsafe settings before setting FrSky failsafe positions. Unusual jitter may result otherwise., 2.3 LED status:, , Please find the how-to guide with the file named “Set up FrSky as a wireless trainer system” via the following link:, www.frsky-rc.com/download.asp?id=23,
Can be used with YS-X4 through one cable, using the ...BevRC
FRSKY TFR8SB- COMPATIBLE WITH FUTABA FAAST RADIO WITH SBUS AND RSSI PORT
| FASST 2.4GHz Air Systems (7CH Mode/Multi Mode) | 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc |
| Model | TFR8SB (8CH FASST compatible receiver with RSSI & SB ports) |
| Dimension | 44.5*27.5*17mm |
| Operating Voltage Range | 3.5~10V |
| Operating Temperature Range | -10℃~80℃ |
| Mode A | RED LED blinks |
| Mode B | GREEN LED blinks |
:11.5g, :, 14ms (FS – Normal Speed Mode), Note: Be sure that when using battery or regulated output from ESC, the capacity must meet the usage conditions of servos., Use native failsafe position preset on the transmitter side:, If not disabling failsafe on the transmitter side, TFR8SB will use native failsafe position preset on the transmitter side., Set failsafe on TFR8SB side:, TFR8SB supports failsafe function for all channels. Follow the steps below to set failsafe on TFR8SB:, 1) Bind the receiver first, and disable failsafe on the transmitter side;, Note: HS mode is only applied for high-speed digital servos. Other servos should select FS mode, otherwise servos will get hot or even burn out., Note: Do not perform linking procedure while motor’s main wire is connected or engine is operating, otherwise damage may occur. After linking is completed, recycle the receiver power and check if the receiver is really under control by linked transmitter.,
It's a good choice for your multi-rotor with Naza or ...BevRC
FRSKY VARIMETRE SENSOR
| Measurement Range of Altitude | 0~9000m |
Accuracy:1m, Installation:, Use double-sided tape to install the variometer sensor on any appropriate surface of the airframe., *Note:, Wind will affect the altitude reading.,
FrSky FVAS-01 Telemetry Variometer Sensor (for use with FrSky Telemetry ...BevRC
FRSKY AMPERE SENSOR-100A
| Dimension | 38*30*10mm |
| Weight | 24g |
| Measurement range | 0~100A |
| Maximum safe current | 100A |
| Sensor current consumption | 33mA |
| Update Rate | ≥1Hz |
| Model | FAS-100 |
| Dimension | 38*30*10mm |
| Weight | 24g |
| Measurement range | 0~100A |
| Maximum safe current | 100A |
| Sensor current consumption | 33mA |
| Update Rate | ≥1Hz |
| Note | When FAS-100 is used with a sensor hub, please make sure the sensor hub is V2.0. |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
3.1 When using the FAS-100, without a FLVS-01:, 3.1.1Connect “Data Out” port of the FAS-100 directly to the “Volt” port on sensor hub using the provided cable., 3.2 When using the FAS-100, with a FLVS-01:, 3.2.1Connect the FAS-100 with, at most, two FLVS-01s and connect the “Data Out” port of FAS-100 or FLVS-01 to the “Volt” port on sensor hub using the provided cable., Driver for XP/ Win7 Vista:, FSH-01 Upgrade ROM_V2.0:, How-to_sensor hub upgrade:,
FAS-100 Category：Accessories Description 1. Introduction The FrSky Ampere Sensor (FAS-100) ...BevRC
FEIYU HORNET OSD
Include:, 1* OSD module,
This is the OSD module from Feiyu, which is already ...BevRC
BEV RED 5.8G CLOVERLEAF ANTENNA 4 LOBES FOR RX(RPSMA,FOLDABLE)
| Frequency Range | 5725-5875Mhz |
| Impedance | 50ohm |
| VSWR | <1.3 |
| Gain | 2dBi |
| Polarization | Right hand circularly polarized |
| Max power input | 20W |
Spec:,
The new batch of cloverleaf antenna with foldable cable, the ...BevRC
OMWAY 5.8G HIGH SENSITIVITY RX(COMPATIBLE WITH ALL 5.8G TX WE SELL)
| Spectations | weight：116g |
| Sterieo audio | L/R audio channe; |
| antenna connector | SMA |
Your purchase includes:, 1* Rx,
This is the first 5.8G solution support both the Fatshark/ImmersionRC(airwave/NexwaveRF) ...