SDSHobby
HIGH IMITATION RC 360 DEGREE ROTATION LARGE NIGHT FLASH LED LIGHT/POLICE CAR LIGHT FOR 1/8 1/10 1:8 1:10 RC CARS (NARROW TYPE)
| Mode 1 | Power default mixed flashing modes, each mode with one cycle |
| Mode 2 | All lights off |
| Mode 3 | Left and right LED flash alternatively |
| Mode 4 | Left and right LED flash alternatively quickly |
| Mode 5 | All the lights flash |
| Mode 6 | Light flashes back and forth inside and outside |
| Mode 7 | The light flash rapidly back and forth inside and outside |
Kindly Remark:, Many, Installation Steps:, 1. Electric vehicle/ oil motor car installation:, . Power supply using special attachment plug, the voltage is 4.8-6V, connected to receiver start lighting, Specifications:, l, Working Voltage:, 4.8-6V, Flashing Mode Works:, seven, Kinds of Flashing Mode:, n, Remote control way:, plug the receiver channel 3, switch remote control of the channel 3, every time switch the switch while switch one flashing mode,
colors are available and will be sent randomly . 3. ...SDSHobby
PROLUX PX1430 5V 1A VOLTAGE CONVERTER/ REGULATOR
Features:, 1. Can change the battery's voltage into 4.7V to 5.7V after connecting with Li-Po battery pack., Kindly Remark:, This Voltage Converter now is,
. Input Volt is 3.7V 3. Output Amp is 1A ...SDSHobby
FVT LCD PROGRAM BOX/ PROGRAM CARD FOR BRUSHLESS CAR ESC
| Dimension | 80x60x18mm |
| Weight | 65g |
| Input Voltage | 4.5V |
| Interface Type | Mini USB, one Futaba connector for ESC, Futaba connector for power |
| Power Supply | DC 4.5V~6V |
| Note 3 | Please |
| USB | connect to PC |
Features:, 1. Can setup the parameters of brushless ESC via the button of LCD program box, Parameters:, l, Connecting Instruction:, 1. Switch off the power of ESC, Note 1:, DO NOT turn step 2 and step 3 upside down, Note 2:, Extra power 4.8-6V will need if the ESC hasn’t BEC. Pay attention the polarity and do not connect wrongly., : first pull BEC flat cable into program card, second connect the program card with 4.8-6V power, and finally connect ESC to main power., Button Instruction:, 1, ITEM:, circularly switch over the program items; exit to the self-defined program item setup; entrance to program item setup, VALUE:, circularly switch over the program item values and self-defined program item, OK:, Save and send the value to ESC; confirm the programmable item, Batt:, power supply port for program card, ESC:, connect with programming port on ESC via programming cable,
. Can update ESC program and setup the parameters by ...SDSHobby
10A ELECTRONIC SWITCH WITH JST PLUG FOR RC MODEL LED LIGHT
| Two types for your choice | 1) JST plug connect with external power version; 2) power from receiver version; |
| Size (without cable) | 35mm*12mm*5mm |
| Voltage | 4-10V ( |
| Max current | 10A, continuous current |
Features:, Specifications:, Weight (with cable): 6g, Applications:, It can be used in RC car and airplane (such as Light’s on and off, Power’s on and off, etc);,
Small size and light weight; Stable performance; Simple control without ...SDSHobby
G.T.POWER LANDING GEAR AND WHEEL DOOR SEQUENCER/CONTROLLER FOR VARIETY OF RC AIRPLANE
| Input Voltage | DC 5~7V |
| Un-load operating Current | <5mA |
Features:, Specifications:, Max load Current: 2A,
Controlled by intelligent chip, pulse width single steady, small working ...SDSHobby
XQ POWER 6V 15KG DIGITAL METAL SERVO WITH 2 BALL BEARINGS AND TITANIUM ALLOY GEAR 25T
| Weight | 73g (2.58oz) |
| Gear Type | Titanium Alloy Gear |
| Bearing | 2 Ball bearings |
| Horn Gear Spline | 25T |
| Connector Wire | 300mm |
| No-load Speed | 0.09 sec/60 degree, 0.07 sec/60 degree |
| Peak Stall Torque | 13 kg.cm, 15 kg.cm |
| Running Degree | 110 degree (when 900~2100 μsec) |
Specification:, Size: A:40mm, B:20mm, C:39.4mm, D:48.0mm, E:10mm,
SDSHobby
XQ POWER 6V 20KG DIGITAL SERVO XQ-S4320D WITH METAL GEARS 25T
Specifications:, Ma. Torque:, 17.2 kg.cm at 4.8V, 20 kg.cm at 6V;, No Load Speed:, , Working Voltage:, , No Load Working Current:, , Weight:, , Arm Rotation Angle:, , Servo Cable Length:, , Gear Material:, Titanium plated gear,
0.14sec/60 at 4.8V, 0.12sec/60 at 6V; 4.8--6.0V 0 mA at ...SDSHobby
X240 OUTRUNNER BRUSHLESS MOTOR KV 2200 FOR RC MODEL AIRPLANES
Specifications:, KV:, 200, Size:, Φ, Weight:, 16.1g/ 0.57oz, Shaft Diameter:, , Shaft Length:, , internal resistance:, 0.52, Maximum efficiency current:, A to 6A, >70%, Maximum operating current:, 8.5A, Measured data:, 3S 800mAh 15C + GWS5030/, Included Equipments and Parameters:, Recommended Equipments (Need to buy separately):,
18mm x 17.5mm (not include shaft) 3.175 mm 12mm Ω ...SDSHobby
XQ POWER 20.5KG RC MODEL BRUSHLESS DIGITAL SERVO XQ-S4618D WITH TITANIUM ALLOY GEARS HIGH GRADE
Specifications :, Weight:, 60g, Size:, 40.2*20.1*38.8mm, Speed:, 0.12sec/60°at 4.8v;, Torque:, 17.4 kg/cm at 4.8v;, Voltage:, 4.8-6.0V, Features:,
0.1sec/60° at 6.0v 0.5 kg/cm at 6.0v High Grade brushless ...SDSHobby
XQ POWER HIGH VOLTAGE XQ-RS420 DIGITAL ROBOT SERVO 21.8KG/60G WITH TITANIUM ALLOY GEAR /ALUMINUM CASE
Specification:, , Weight:, , Size (L*W*H):, , Speed:, , Torque:, , Voltage:, , Bearing quantity:, Horn gear spline:, 5T, Splash water resistance:, Yes, Connector:, , Features:,
56g ± 0.2 40.2mm*20.1mm*38.8mm 0.15sec/60 ° at 6.0v; 0.13sec/60 ° ...SDSHobby
XQ POWER 14.5KG/62G DIGITAL ROBOT SERVO XQ-RS313E WITH METAL GEAR 25T FUTABA
Specifications:,
SDSHobby
XQ POWER 14.5KG/56G DIGITAL ROBOT SERVO XQ-RS413 WITH TITANIUM GEAR/ALUMINUM CASE
Specifications:,
SDSHobby
XQ-POWER 40KG/162G DIGITAL SERVO XQ-S5040D BIG TORQUE WITH METAL GEAR/ALUMINUM CASE
Specifications:,
SDSHobby
XQ POWER 16.9KG/56G DIGITAL SERVO XQ-S4116D HIGH VOLTAGE 8.5V WITH TITANIUM GEAR/ALUMINUM CASE
Specifications:,