HobbyKing
SUPER BRIGHT 3WATT YELLOW LED LAMP WITH ALUMINIUM HEATSINK
| Input | 2.5-3 volts |
| Colour | Yellow |
| Brightness | 70-80 Lumens |
| Diameter | 20mm |
Spec:, Weight:4g,
This Super Bright 3 watt Yellow LED comes mounted to ...5 Reviews
HobbyKing
LED RED, GREEN, BLUE (RGB) STRIP 50CM W/FLYING LEAD
| Requires | 12volt power source |
Specs:, • 30 RGB LEDs,
These LED strips contain 30 RGB (Red,Green, Blue) LEDs per ...HobbyKing
WHITE 16 LED CIRCULAR LIGHT BOARD WITH LEAD
| Voltage | 9-11v Dc |
| Colour | White |
| Diameter | 50mm |
Spec:, Mounting:, diameter 2mm, spacing 35mm, Weight:8g,
This circular LED light has 16 LED's mounted to an ...5 Reviews
HobbyKing
YELLOW 16 LED CIRCULAR LIGHT BOARD WITH LEAD
| Voltage | 9-11v Dc |
| Colour | Yellow |
| Diameter | 50mm |
Spec:, Mounting:, diameter 2mm, spacing 35mm, Weight:8g,
This circular LED light has 16 LED's mounted to an ...1 Reviews
HobbyKing
90 DEGREE PIN HEADER 2 ROW 30PIN 2.54MM PITCH (5PCS)
,
Need to repair crash damage to a Multi-rotor flight board ...5 Reviews
HobbyKing
90 DEGREE PIN HEADER 3 ROW 30 PIN 2.54MM PITCH (5PCS)
,
Need to repair crash damage to a Multi-rotor flight board ...5 Reviews
HobbyKing
TURNIGY 4208 620KV BRUSHLESS MULTI-ROTOR MOTOR
| Can size | 45mm |
| Motor Mount Holes | 16mm / 19mm |
| Rated Watts | 180W |
| Weight | 79g |
| Cell count | 3~4S |
| Motor wire length | 390mm |
Specs:Kv, :620rpm/v, Shaft:, 3.17mm (includes prop adapter for 5mm prop mounting), :30A,
If you're serious about your multi-rotor's performance, look no further ...5 Reviews
HobbyKing
HOBBYKING Q-BOT QUADCOPTER (MODE 2) (RTF)
| Width | 220mm |
| Height | 55mm |
| Weight | 63g |
| Included in box | Q-BOT Quadcopter |
Features:, 3-axis gyro stabilization system, Specs:, Transmitter mode:, Mode 2 (throttle on LEFT stick), Requires:, 4 x AA batteries for transmitter,
The Q-BOT Quad features an advanced 3-axis gyro stabilization system ...5 Reviews
HobbyKing
MULTIROTOR CF PROPELLER PAIR 17 X 5.5 LEFT AND RIGHT ROTATION TO SUIT PANCAKE MOTORS
| Diameter | 17 inches |
| Pitch | 5.5 inches |
| Rotation | Left and Right pair |
| Shaft Hole diameter | 5mm |
| Drive Hole diameter | 3mm |
Specs:, Spacing:, 7mm (center to center - Shaft hole to drive hole),
These propellers are specifically designed for multirotor use and for ...HobbyKing
MULTIROTOR CF PROPELLER PAIR 15 X 5.5 LEFT AND RIGHT ROTATION TO SUIT PANCAKE MOTORS
| Diameter | 15 inches |
| Pitch | 5.5 inches |
| Rotation | Left and Right pair |
| Shaft Hole diameter | 5mm |
| Drive Hole diameter | 3mm |
Specs:, Spacing:, 7mm (center to center - Shaft hole to drive hole),
These propellers are specifically designed for multirotor use and for ...5 Reviews
HobbyKing
WALKERA QR INFRA X MICRO QUADCOPTER W/IR AND ALTITUDE HOLD (MODE 1) (RTF)
| Width | 170mm |
| Height | 60mm |
Features:, • 6-axis gyro stabilization system, Specs:, Weight:, 58.5g (w/out battery), Transmitter mode:, Mode 1 (right stick throttle), Included in box:, QR Infra X Micro Quadcopter, Required:, 4 x AA batteries for transmitter,
*On sale for a limited time, only $114.99! The QR ...HobbyKing
CARBON FIBER PROPELLERS 12X6 LH AND RH ROTATION PAIR
| Diameter | 12 inch |
| Pitch | 6 inch |
| Hub thickness | 8mm |
| Shaft diameter | 6mm |
| Weight(each) | 19g |
Specs:,
These are some nice Carbon Blades for Multi-rotor projects, they ...HobbyKing
CARBON FIBER PROPELLERS 11X4.7 LH AND RH ROTATION PAIR
| Diameter | 11 inch |
| Pitch | 4.7 inch |
| Hub thickness | 8mm |
| Shaft diameter | 6mm |
| Weight(each) | 15g |
Specs:,
These are some nice Carbon Blades for Multi-rotor projects, they ...5 Reviews
ngHobbies
WI 232 V2.0 MODULE PAIR
The following items are included in this kit:, 1 x Wi232 ground station module, Instructions:, Setup and instructions on wiki,
This set contains two ready assembled and preconfigured WI232 V2.0 ...ngHobbies
MIKROKOPTER BASIKSET OKTO 2-26
| http | //www.nghobbies.com/cart/index.php?main_page=page&id=23 |
| Note | There is NO battery included with this kit. |
| http | //www.mikrokopter.de/ucwiki/en/MK-Okto |
| http | //www.mikrokopter.com/ucwiki/en/Mikrokopter-Get-started |
| http | //www.mikrokopter.com/ucwiki/en/FlightCtrlManual |
| http | //www.mikrokopter.com/ucwiki/en/BrushlessCtrl |
| http | //www.mikrokopter.com/ucwiki/en/SerCon |
| http | //www.mikrokopter.com/ucwiki/en/ElectronicConnections |
| http | //www.mikrokopter.com/ucwiki/en/MikroKopter-Tool |
| http | //www.mikrokopter.de |
| http | //forum.mikrokopter.de/forum-17.html |
NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, , Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,
pre-order only . We will order this when you place ...