BevRC
FRSKY D4R-II TINY TELEMETRY RECEIVER WITH CCPM AND RSSI PORT
| Compatible with FrSky two-way telemetry modules | DFT, DJT, DHT, DHT-U |
| Operating Voltage Range | 3.5V~10V |
| Operating Current | 60mA |
| Operating Range | Full Range (>1.5km) |
| Dimension | 40x22.5x6mm |
| Weight | 5.8g |
Compatibility:, Features:, • RSSI (PWM) and CPPM output., Specs:, Number of Channels:4,
It's your best choice for small plane or coptors, such ...BevRC
FRSKY D8R-II PLUS TELEMETRY RECEIVER
FrSky provides an additional ..." />
| Compatible with FrSky two way telemetry modules | DFT, DJT, DHT, DHT-U |
| Operating voltage | 3.5~10.0V |
| Power consumption | 100mA |
| Resolution | 3072 |
| Analog voltage | 0~3.3V |
| Range | 1.5km-2.5km |
| Dimensions | 55 x 25 x 14 mm |
| Weight | 12.4g |
Features:, Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., Compatibility:, Receiver Specification:, Number of channels: 8,
The Two-way Radio System developed by FrSky provides an additional ...BevRC
FRSKY DJT COMBO PACK FOR JR WITH V8FR-II
FrSKY ACCST technology is proven, approved by many model associations, ..." />
| Operating voltage | 3.0~16V |
| Power consumption | 30mA |
| Resolution | 3072 |
| Latency | 22ms |
| Range | 1.5km-2.5km |
| Dimensions | 44 x 24 x 14 mm |
| Weight | 9.3g |
| Power consumption | 50mA |
| Resolution | 3072 (11bit) |
| Dimensions | 63.9x48.5x36.5mm |
Features:, Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., FrSky DJT is compatible with JR transmitters following:, JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, PX, 9XII, 11XZERO, Receiver Specification:, Number of channels: 8, Module specification:, Operating voltage:, 6.0V-13.0V (can handle 3S!), Output Power:: 60mW,
FrSKY ACCST technology is proven, approved by many model associations, ...BevRC
FRSKY AMPERE SENSOR-100A
FrSky Ampere Sensor (FAS-100) ..." />
| Dimension | 38*30*10mm |
| Weight | 24g |
| Measurement range | 0~100A |
| Maximum safe current | 100A |
| Sensor current consumption | 33mA |
| Update Rate | ≥1Hz |
| Model | FAS-100 |
| Dimension | 38*30*10mm |
| Weight | 24g |
| Measurement range | 0~100A |
| Maximum safe current | 100A |
| Sensor current consumption | 33mA |
| Update Rate | ≥1Hz |
| Note | When FAS-100 is used with a sensor hub, please make sure the sensor hub is V2.0. |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
3.1 When using the FAS-100, without a FLVS-01:, 3.1.1Connect “Data Out” port of the FAS-100 directly to the “Volt” port on sensor hub using the provided cable., 3.2 When using the FAS-100, with a FLVS-01:, 3.2.1Connect the FAS-100 with, at most, two FLVS-01s and connect the “Data Out” port of FAS-100 or FLVS-01 to the “Volt” port on sensor hub using the provided cable., Driver for XP/ Win7 Vista:, FSH-01 Upgrade ROM_V2.0:, How-to_sensor hub upgrade:,
FAS-100 Category：Accessories Description 1. Introduction The FrSky Ampere Sensor (FAS-100) ...BevRC
FRSKY LIPO VOLTAGE SENSOR
FrSky Lipo ..." />
| Dimension | 45*21*7mm |
| Weight | 5.2g |
| Measurement range | 1S~6S (The first lipo voltage should be more than 3.55V) |
| Cell voltage display range | 0.20~4.20V |
| Model | FLVS-01 |
| Dimension | 45*21*7mm |
| Weight | 5.2g |
| Measurement range | 1S~6S (The first lipo voltage should be more than 3.55V) |
| Cell voltage display range | 0.20~4.20V |
| Voltage display resolution | 0.01V |
| Voltage detection precision | 0.05V |
| Current of the board | 15.5mA |
| Operating temperature range | -30℃~70℃ |
| Pixel | 128*64 with OLED display screen |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=22 |
| http | //www.frsky-rc.com/download.asp?id=23 |
| http | //www.frsky-rc.com/download.asp?id=23 |
1. Specifications:, , ﹡Note:, When FLVS-01 works with sensor hub and FLD-02/DHT-U to display total voltage and cell voltages as connected, please refer to below points:, , Driver for XP/ Win7 Vista:, FSH-01 Upgrade ROM_V2.0:, How-to_sensor hub upgrade:, Driver for XP/ Win7 Vista:, DHT-U Upgrade ROM_V2.0:, How-to_DHT-U upgrade:,
Product Show FLVS-01 Category：Accessories 2. Set Up 2.1 FrSky Lipo ...BevRC
FRSKY LCD DISPLAY
| Model | FLD-02 |
| Compatibility | FrSky DFT, DJT and DHT |
| Dimension | 55*40*12mm |
| Pixel | 128*64 |
| Model | FLD-02 |
| Compatibility | FrSky DFT, DJT and DHT |
| Dimension | 55*40*12mm |
| Pixel | 128*64 |
| Blade | Blade Number |
| Volt ratio | A1 & A2 Voltage Division Ratio |
| Unit Set | Speed (m/s or MPH) |
| Alarm Set | A1_1/2, A2_1/2, RSSI_1/2 |
1.1 Specifications:, 1.2 Features:, 1) Show all connected sensors data;, 2. Installation:, Connect FrSky FLD-02 to the UART and power connection on FrSky telemetry module (Rxd, Txd, +5V, GND) by the provided cable. Confirm the orientation is correct and make sure both switches on the telemetry module are OFF, 3 Screen structures:, 3.1 Main Screen, Note: Make sure the battery voltage division ratios are programmed in accordance with those of connected battery voltage sensors., :, , Note: Screen-3 shows up only when FrSky Lipo Voltage Sensor (FLVS-01) is connected, otherwise Screen-4 will show up after Screen-2.,
Product Show FLD-02 Category：Accessories 1.Introduction 2) Capable of programming alarm ...BevRC
FRSKY SENSOR HUB
FrSky Sensor Hub ..." />
| Dimension | 37*30*8mm |
| Operating Voltage Range | 4~10V |
| Operating Temperature Range | -20~80℃ |
| Feature | Firmware upgradable |
| Fuel | Fuel Gauge Sensor |
| GPS | GPS |
| Vario | Variometer Sensor |
| Volt | Lipo Voltage Sensor |
| Temp1/2 | Temperature Sensor |
| Power | Power Supply |
| RPM | RPM Sensor |
| Acc | Triaxial Acceleration Sensor |
| Data | use provided cable to connect to digital side port (G, TX, RX) of FrSky telemetry receiver |
: 37*30*8mm, :, Operating Voltage Range, : 4~10V, : -20~80℃, : Firmware upgradable, :, , Installation:, It is recommended to take the length of all sensors’ wires into consideration before mounting, and use double-sided tape to install FrSky sensor hub at an appropriate place in the model.,
Product Show Sensor Hub and Sensors Category：Accessories FrSky Sensor Hub ...BevRC
FRSKY DJT COMBO PACK FOR JR WITH D8R-II PLUS TELEMETRY
| Operating voltage | 4.0~7.2V / 3.0~16V(HV Version) |
| Power consumption | 30mA |
| Resolution | 3072 |
| Latency | 22ms |
| Analog voltage | 0~3.3V |
| Range | 1.5km-2.5km |
| Dimensions | 49 x 24.5 x 15 mm |
| Weight | 14g |
| Version | 2.0 |
| Operating voltage | 6.0V-13.0V (can handle 3S!) |
| Power consumption | 50mA |
| Resolution | 3072 (11bit) |
| Dimensions | 63.9x48.5x36.5mm |
| Version | 2.0 |
Features:, Advanced Continuous Channel Shifting Technology (ACCST is our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., FrSky V8JT is compatible with JR transmitters following:, JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, MX 22, MX-24S, PX, 9XII, Receiver Specification:, Number of channels: 8, Module specification:, Output Power:: 60mW,
Easy to bind and very fast link-up. Excellent reboot time. ...BevRC
FRSKY TFRSP- FUTABA FASST COMPATIBLE WITH SPPM AND RSSI PORT
| FASST 2.4G Air Systems (7CH Mode/Multi Mode) | 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc. |
| Number of Channels | up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10) |
| Operating Voltage Range | 3.5V~10V |
| Operating Temperature Range | -10℃~60℃ |
| Dimension | 53mm*30mm*11mm |
| Weight | 13.5g |
| Note | Increased duty means good signal reception, and vice verse. |
1.1 Compatibility:, 1.2 Specifications:, Warning: Servos are not to be plugged into Channel CPPM and Channel RSSI, otherwise servos will get hot or may burn out., 2.1 Bind procedure:, Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally., 2.2 Setting failsafe:, TFRSP supports failsafe function for all channels. Follow the steps below to set failsafe:, 1) Bind the receiver first, and disable failsafe on the transmitter side;, Warning: Some transmitter manufacturers use a failsafe method that can interfere with that used by FrSky. Be sure to disable any transmitter failsafe settings before setting FrSky failsafe positions. Unusual jitter may result otherwise., 2.3 LED status:, , Please find the how-to guide with the file named “Set up FrSky as a wireless trainer system” via the following link:, www.frsky-rc.com/download.asp?id=23,
Can be used with YS-X4 through one cable, using the ...BevRC
FRSKY BATTERY VOLTAGE SENSOR LITE
| FrSky D series accessories | serial cable |
| http | //www.frsky-rc.com/download.asp |
Introduction:, FrSky Battery Voltage Sensor is provided as Two Way Telemetry System’s Optional Accessory. There are three voltage ranges to choose: 1S lipo for battery voltage range from 0V~6.6V, up to 3S lipo for 0V~13.2V and up to 5S lipo for 0V~19.8V. Please check the battery voltage division ratio for each option below:, Recommended Voltage Option Max Lipo Pack Count Battery Voltage Division Ratio, 1S 1S 2:1, 2S 3S 4:1, 3S 5S 6:1,
Product Show FBVS-01 Category：Accessories Description More detail：BevRC
FRSKY 7DB PATCH ANTENNA FOR TX MODULE
Frsky Tx module to enlarge the control range." />
,
For Frsky Tx module to enlarge the control range.BevRC
FRSKY 5DB UPDATE ANTENNA
frsky Tx module to enlarge the control range." />
,
For frsky Tx module to enlarge the control range.BevRC
FRSKY D8R-XP TELEMETRY RECEIVER WITH CPPM PORT
FrSKY ACCST technology is proven, approved by many model associations, ..." />
| Operating voltage | 3.0~16V(HV Version) |
| Power consumption | 30mA |
| Resolution | 3072 |
| Latency | 22ms |
| Range | 1.5km-2.5km |
| Dimensions | 56 x 25 x 20 mm |
| Weight | 12.2g |
Features:, Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., Receiver Specification:, Number of channels: 8,
FrSKY ACCST technology is proven, approved by many model associations, ...BevRC
FRSKY FIRMWARE UPDATER TOOL
Frsky products." />
,
Used for the firmware update of Frsky products.BevRC
FRSKY V8FR-II RX
FrSKY ACCST technology is proven, approved by many model associations, ..." />
| Operating voltage | 3.0~16V(HV Version) |
| Power consumption | 30mA |
| Resolution | 3072 |
| Latency | 22ms |
| Range | 1.5km-2.5km |
| Dimensions | 44 x 24 x 14 mm |
| Weight | 9.3g |
Features:, Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility., Receiver Specification:, Number of channels: 8,
FrSKY ACCST technology is proven, approved by many model associations, ...