Futaba Page 16 Review

HobbyKing

HEAVY DUTY 25T ALUMINUM SERVO ARM - FUTABA (BLUE)

Futaba (Blue)" />

Specifications:, Lenght:, 19mm (Center to Hole 1), 24mm (Center to Hole 2),

Heavy Duty 25T Aluminum Servo Arm - Futaba (Blue)

HobbyKing

ALUMINUM ONE-WAY UNIVERSAL SERVO ARM - JR, FUTABA & HITEC (RED)

Futaba & HITEC ..." />

Specifications:, Lenght:, 10mm (Center to Hole 1), 14mm (Center to Hole 2), 18mm (Center to Hole 3),

Aluminum One-way Universal Servo Arm - JR, Futaba & HITEC ...

HobbyKing

ALUMINUM ONE-WAY UNIVERSAL SERVO ARM - JR, FUTABA & HITEC (PURPLE)

Futaba & HITEC ..." />

Specifications:, Lenght:, 10mm (Center to Hole 1), 14mm (Center to Hole 2), 18mm (Center to Hole 3),

Aluminum One-way Universal Servo Arm - JR, Futaba & HITEC ...

5 Reviews

HobbyKing

ALLOY HEAVY DUTY SERVO ARM 37MM X M2 - FUTABA

Futaba" />

Alloy Heavy Duty Servo Arm 37mm x M2 - Futaba

5 Reviews

HobbyKing

SERVO SAVER WITH INSERTS FOR FUTABA, HITEC, AIRTRONICS & KO SERVO SPLINES

Futaba, HiTec, Airtronics & KO ..." />

Servo Saver with inserts for Futaba, HiTec, Airtronics & KO ...

HobbyKing

FUTABA/HITEC TRANSMITTER ADAPTER PLUG 3.5MM TO DIN6 FOR FLIGHT SIMULATOR

Futaba/Hitec Transmitter Adapter Plug 3.5mm to DIN6 for Flight Simulator" />

Length	152mm

Specs:, Plug types:, Female 3.5mm to Male DIN6,

Futaba/Hitec Transmitter Adapter Plug 3.5mm to DIN6 for Flight Simulator

BevRC

FRSKY TFR8SB- COMPATIBLE WITH FUTABA FAAST RADIO WITH SBUS AND RSSI PORT

FASST 2.4GHz Air Systems (7CH Mode/Multi Mode)	6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc
Model	TFR8SB (8CH FASST compatible receiver with RSSI & SB ports)
Dimension	44.527.517mm
Operating Voltage Range	3.5~10V
Operating Temperature Range	-10â„ƒ~80â„ƒ
Mode A	RED LED blinks
Mode B	GREEN LED blinks

:11.5g, :, 14ms (FS – Normal Speed Mode), Note: Be sure that when using battery or regulated output from ESC, the capacity must meet the usage conditions of servos., Use native failsafe position preset on the transmitter side:, If not disabling failsafe on the transmitter side, TFR8SB will use native failsafe position preset on the transmitter side., Set failsafe on TFR8SB side:, TFR8SB supports failsafe function for all channels. Follow the steps below to set failsafe on TFR8SB:, 1) Bind the receiver first, and disable failsafe on the transmitter side;, Note: HS mode is only applied for high-speed digital servos. Other servos should select FS mode, otherwise servos will get hot or even burn out., Note: Do not perform linking procedure while motor’s main wire is connected or engine is operating, otherwise damage may occur. After linking is completed, recycle the receiver power and check if the receiver is really under control by linked transmitter.,

It's a good choice for your multi-rotor with Naza or ...