BevRC
TAROT T2D GOPRO HERO3 TWO-AXIS BRUSHLESS GIMBAL/WITH GYRO
| 7, support Receiver | conventional receiver, S-BUS receiver, DSM2/DSMJ/DSMX receiver |
| 8, support for remote devices | PPM/PCM/2.4G |
| 9, the working voltage | DC 7.4V ~ 14.8V (Recommended 12V, three lithium battery) |
| 10, working current | 200mA-500mA (power supply voltage and the motor related) |
| 11, the working environment temperature | -15 ℃ ~ 65 ℃ |
| 12, the processor | Dual 32-bit high-speed ARM core processor |
| 13, the sensor | Three rotor MEMS gyroscope rotor MEMS accelerometers and the three |
| 14, the maximum angular rate | 2000°/ sec |
| 15, the maximum acceleration | 16g |
| 16, the control frequency | 2000Hz |
| 17, the motor drive frequency | 20KHz (no noise smoothing driven) |
| 18, the control accuracy | 0.1° |
| 19, the control angle range | -45 °~ 45 °(roll), -135°~ 90°(tilt) |
| 20, pose solver algorithms | PTZ dedicated brushless motor decoupled EKF algorithm |
| 21, for shooting equipment | GOPRO Hero3 |
| Weight | 195g |
Gopro two-axis brushless PTZ English software description and download link:, , Product Features:, 1, support GOPRO Hero3 video auxiliary output, Related Part Number:, Head hanging hook TL68A01, Specifications:, GOPRO brushless pan rack assembly TL68A08 x1,
Download the manual here. T-2D PTZ is TAROT company for ...BevRC
MASTOR-G BRUSHLESS GIMBALS FOR GOPRO(FREE SHIPPING IN EXPEDITED WAY)
| Free Download | firmware update.zip |
| Weight | 232g without camera |
| roll | 0.07 degrees; pitch |
| 12-hours angle drift | 0.12-1.5 degrees |
| Suitable payload | 120g-400g |
| Suitable flying wind Speed | < 38km/h |
Free Download:, Mastor-G quick start manual 2013-5-18.pdf, Free Download:, GoPro-G Assistant Software.zip, Leave us a note in your order such as:, 1: what lipo you plan to use, 3 cell or 4 cell lipo, 2: what camera you plan to use, gopro hero1/2 or hero3, All the gimbals shipped after 18th, May will be registered and with the sticker marked the SN number and register code, as below pic shows, pre adjusted with 3s lipo and naked gopro:, , ry please send email to:, support@bevrc.zendesk.com, Specs:, Based on STM32 32-bits high-speed MCU(tens of times faster than other open-source solutions), Size:, 10.7(12.5)*11*12cm, Roll angle limit:, > 360 degrees, Pitch angle limit:, >180 degrees, can be controlled by any p, : roll: 178 degrees/s; pitch: 182 degrees/s, Control accuracy:, Recommend camera:, gopro hero1,hero2, hero3, or similar cameras, Power:, 2-4 cell lipo, 3-cell recommend, can be powered as high as 6-cell(the high voltage input need to be reduce the power output parameters in the configuration tool.), COG adjustment range: X: 28mm Y:12mm Z:36mm,
We will pre-adjust it well for you to guarantee you ...HobbyKing
GOPRO HERO3 GLASS FIBER CAMERA MOUNT
| Application | GoPRO HERO3 |
| Interior Dimensions (mm) | 60Lx25Wx45H |
| Weight | 55g |
Specs:,
This camera mount is contructed from strong yet lightweight glass ...5 Reviews
ReadyMadeRC
GOPROFESSIONAL CASES - PHANTOM/GOPRO HARD CASE
| Exterior Dimensions | 20.25" x 16.93" x 8.78" |
| Weight | 13.15 lbs |
Features:, All our products are the highest water-jet precision cut. We never cut corners and die-cut or punch cut our custom cases., The XB-DJI Will Fit 9" Props:, 1 DJI Phantom, GoPro Equipment:, 1 Additional GoPro Hero, Specifications:,
Go Professional Cases Introduces the XB-DJIFS The Elite Original Customized ...HobbyKing
GOPRO HERO 2 TO FPV TRANSMITTER LEAD - 150MM
| Cable length | 150mm |
Specs:, Connector:, 2.5mm to single pin connections, Note:, This cable is designed for video/audio out only, you must use the GoPro 2 Battery as the cameras power source.,
This handy cable will connect to the 2.5mm A/V port ...5 Reviews
HobbyKing
X-CAM X100B 2-AXIS BRUSHLESS CAMERA GIMBAL FOR GOPRO (PLUG AND PLAY)
| Motor Travel Limit | +/- 90° |
| Sensor Resolution | 0.015 |
| Twin Rail Mount Width | 59~60mm |
| Weight | 230g |
*Compatibility:, This gimbal is compatible with the GoPRO Hero 1~3 and other similar sized cameras., Features:, • Designed for use with the GoPRO Hero 1~3 and other similar sized sports cameras, Specs:, Input Voltage:, 12V (recommended to use a 12V BEC), *Note:, The X-Cam Brushless Gimbal PC Assistant software, USB link drivers and User Manual can be downloaded from the "Files" tab below.,
This is the X-Cam X100B 2-axis brushless camera gimbal for ...5 Reviews
ReadyMadeRC
GOPRO-HOUSING "SNAP" V2.0 FOR GOPRO HD2 - WHITE
GoPro-housing, which offers a perfect protection of ..." />
| Weight of the housing alone | 23 grams |
| Disclaimer | I suggest clipping off one side of the |
Most important changes:, - Screw-mechanism instead of the snapping mechanism (details see below), All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With version 1 there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the, A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),
"Snap" is a GoPro-housing, which offers a perfect protection of ...ReadyMadeRC
GOPRO-HOUSING "SNAP" V2.0 FOR GOPRO HD2 - BLACK
GoPro-housing, which offers a perfect protection of ..." />
| Weight of the housing alone | 23 grams |
| Disclaimer | I suggest clipping off one side of the |
Most important changes:, - Screw-mechanism instead of the snapping mechanism (details see below), All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With version 1 there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the, A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),
"Snap" is a GoPro-housing, which offers a perfect protection of ...ReadyMadeRC
GOPRO - DUAL CAMERA HOUSING GOPRO+CCD HERO1&2 - WHITE
"Snap-In"-Mechanism for a complete protection and a stable mounting:, We are especially proud of this, thats why the housing has been named after it: Due to a front-plate with a "snap"-mechanism, the box is completely sealed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using the 3 countersunk screws and the buttefly nuts included in the Quadrixette 30-frames, the housing can be mounted very flexible, :, "Snap" can be easily installed/uninstalled on the Quadrixette 30/40. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video).,
"Click" is a mounting system for cameras in the FPV-area. ...ReadyMadeRC
GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - BLACK
GoPro-housing offers a perfect protection of your GoPro against ..." />
| Weight of the housing includingg screws and lens protection | 30 grams |
| Disclaimer | I suggest clipping off one side of the nut a bit, so there won't be any part of it that would |
All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),
This GoPro-housing offers a perfect protection of your GoPro against ...ReadyMadeRC
GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - WHITE
GoPro-housing offers a perfect protection of your GoPro against ..." />
| Weight of the housing includingg screws and lens protection | 30 grams |
| Disclaimer | I suggest clipping off one side of the nut a bit, so there won't be any part of it that would |
All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),
This GoPro-housing offers a perfect protection of your GoPro against ...ngHobbies
GOPRO HERO 3 FPV IMMERSIONRC CABLE WITH POWER
GoPro ..." />
. The USB connector fits the GoPro Hero 3 cameras AV plug and the 5 pin Molex type connector has been provided to be plug and play with the video 2.4GHz and 5.8GHz transmitters designed and manufactured by Immersion RC. The 5 pin Molex connector has the following connections:, Brown - Ground connection, The power requirement for the GoPro camera is minimum 1A at 5V. The provided servo cable connections are:, Red - +5V (Do not exceed 5V), Please note:, The Immersion RC or Fatshark transmitters CANNOT supply enough power on the 5V out line to power the GoPro camera in flight. DO NOT risk it, it will damage your Immersion RC transmitter - or you will loose your transmitter in the air!!!,
Beside the FPV audio and video feed from a GoPro ...SDSHobby
CNC ALUMINIUM ALLOY BRUSHLESS GOPRO CAMERA GIMBAL FOR FPV AERIAL PHOTOGRAPHY/ GOPRO3
Gopro ..." />
| 4. Support Receiver | general receiver, S-BUS receiver, DSM2/ DSMJ/ DSMX receiver. |
| 5. Remote control | PPM/ PCM/ 2.4G |
| 6. Operating Voltage | DC 7.4V~14.8V (recommended 12V, 3-cell lithium battery) |
| 7. Operating Current | 200mA-1000mA (Related to supply voltage and motor power) |
| 8. Operating Temperature | -18°C~70°C |
| 9. Control frequency | 2000Hz |
| 10. Motor driving frequency | 20 KHz (noiseless smooth drive) |
| 12. Controlled angle range | -45~45degree (roll), -60~60degree (pitch) |
| 13. Suitable film device | GOPRO Hero3, GOPRO Hero3+ |
Product Description:, Features:, 1. Support video, 11. Control precision:, 0.1 degree, 17. Whole weight:, 160g, Package Details:, *Attention:, GOPRO3 camera,
GOPRP3 ( free debugging ) gimbal is designed for Gopro ...RCPlanet
WALKERA QR X350 QUADCOPTER RTF DEVO 7 RADIO W/GOPRO HERO 3+ CAMERA GPOCHDHX-301
GoPro Camera, Optics:, Ultra sharp ƒ/2.8 6-element aspherical glass lens / Ultra wide angle / reduced distortion / 2X Better low-light performance, Video format:, H.264 codec, .mp4 file format, White Balance:, Auto and manual, Resolutions:, 12, 7, 5MP, Burst:, 30 photos per second, Continuous Photo:, 3 photos per second, 5 photos per second, 10 photos per second, Time-lapse:, 0.5, 1, 2, 5, 10, 30, 60 second intervals, Simultaneous Photo and Video:, 12MP + 1440p24 fps, 8MP + 1080p30 fps 8, 8MP + 720p60 fps, Battery and Charging:, 1050mAh rechargeable lithium-ion / Charge via USB, Audio:, Mono, 48kHz, AAC compression w/ AGC, and supports optional 3.5mm stereo mic adapter, Memory:, MicroSD class 10 or higher required / Up to 64GB capacity supported, Included Cables:, USB charging cable, Operating System:, Microsoft Windows Vista, 7 and later, Quadcopter, Main Rotor Diameter:, 21.8in (556mm), Main Rotor Blade Length:, 8.1in (206mm), Main Motor Size:, WK-WS-28-008A, Battery:, 11.1V 2200mAh 25C LiPo, Length:, 11.3in (289mm), Width:, 11.3in (289mm), Height:, 7.0in (180mm), Flying Weight:, approx 2.20lbs (35.2 oz), Approximate Flight Time:, 10-15 minutes, Rotor Type:, QuadCopter, Experience Level:, Intermediate, Completion Level:, Ready to Fly (RTF), Recommended Environment:, Indoor and Outdoor, Tips & Tricks, More Info, ,
This is the brand new Walkera QR X350 Quadcopter RTF ...ReadyMadeRC
GOPRO HEAD STRAP + QUICKCLIP
| Warranty | 1 Year |
Restrictions:, According to GoPro policy, sales of the GoPro cameras from this store are restricted to the United States only.,
Includes a Head Strap and a QuickClip for a variety ...