RCModelScout.

HobbyKing

EXTENDED LANDING SKID SET FOR SK450 QUADCOPTER FRAME

*Note:, This is an extended landing skid set only, SK450 multi-rotor frame sold separately, Specs:, Weight:, 93g (w/all hardware), Includes:, Complete extended landing skid set,

HobbyKing

MICRO INTEGRATED PCB W/ESCS QUADCOPTER FRAME 235MM (KIT)

Features:, Compact, lightweight design, Specs:, Weight:, 82g (w/out electronics), Required:, 4 x brushless outrunner motors,

ngHobbies

MIKROKOPTER BASIKSET L4-ME

NOTE:, Please note this kit is, Please make sure you read and understand the warranty information on these kits before purchasing:, The Mikrokopter is an open source project with a very big support from Germany and all over Europe. The Mikrokopter kit contains everything to get the Mikrokopter in the air in about 5-10 hours of work. The skills needed to make this happen are: soldering, mechanical, good understanding of electronics, airplanes. To fly the Mikrokopter you need a good understanding of helicopter controls. If you ever flew a model helicopter you'll be flying the Mikrokopter in no time., The package contains:, 1 x preassembled FlightCtrl ME V2.1 with Altitude Sensor, Documentation:, Assembly manual:, English getting started page:, English Flight controller manual:, English Brushless ESC manual:, English Serial converter manual:, English wiring diagram:, English Mikrokopter tool:, There is also an international section of the Mikrokopter forum:,

HobbyKing

TURNIGY TALON TRICOPTER (V1.0) - EXTENDED CARBON FIBRE BOOM (380MM) (3PCS)

,

HobbyKing

TURNIGY TALON TRICOPTER (V1.0) - INTEGRATED TAIL SERVO MOUNT SET

,

HobbyWireless

GAUI GM-412S SCORPION BRUSHLESS MOTOR (400W-KV960)

Details:, , Description:,

HiModel

X-CAM 2 AXIS GIMBAL STABILIZATION MODULE GSM110

, , , , , , Specifications:, , , , , , , , , , , X-CAM 2 Axis Gimbal Stabilization Module GSM110, Specification：, Input Voltage： 5, - 6V, Volume：, 45 x 35 x 10 mm, There are 4 versions of this series product available, And this one is version GSM110., How to use the Remote Controller for Servo Reverse Setup ：, 1.  Connect to channel CH5 on the Printed Circuit Board (PCB), 2.  Push this channel to the highest position on your Remote Controller, 3.  There will be 3 BEEPs followed by the Red LED flashing, Return the Remote Controller Lever to the middle position to enter the Servo Reverse Setup mode, 4.  Move the Remote Controller Lever to the Highest or lowest position to set the Servo Reverse after hearing the BEEPs., (One BEEP means Channel 1 (TILT) , Two BEEP means Channel 2 (ROLL), Three BEEP means Channel 3 (PAN) ),, If you do not want to change the setup, Just move the  Remote Controller Lever to the Middel position., 5.  When you hear 4 BEEPs, the setup has been saved., How to adjust the Acc. Gain:, Rotate the Blue Potentiometer on the PCB for adjust the Acc. Gain., PC software for setup, , ,

HobbyKing

TURNIGY PLUSH 40AMP SPEED CONTROLLER

HobbyKing

TURNIGY PLUSH 60AMP SPEED CONTROLLER

HobbyKing

TURNIGY PLUSH 10AMP 9GRAM SPEED CONTROLLER

Weight: 9g,

HobbyKing

TURNIGY PLUSH 25AMP SPEED CONTROLLER

HobbyKing

NX-4006-530KV BRUSHLESS QUADCOPTER MOTOR

Kv:530rpm/v, Shaft:, 3mm (Includes Prop saver mount for GWS style props),

HobbyKing

TURNIGY TALON CARBON FIBER QUADCOPTER FRAME

Specs:,

HobbyKing

HOBBYKING X525 V3 GLASS FIBER MOTOR MOUNT (4PCS/BAG)

,

HobbyKing

HOBBYKING X550 GLASS FIBER QUADCOPTER FRAME 550MM

Specs:, Required:, Multi-Rotor control board, Note:, All Hobbyking X series frames are purchased factory direct. We have worked closely with the factory engineers to ensure quality. All X series frames are CNC cut and accurately milled unlike many of the cheap frames available from Ebay or Chinese vendors that are drilled by hand in low tech factories. The Hobbyking X series also feature thicker GF main plates for added stength.,