HobbyKing
COUNTER ROTATING THREE BLADE 6X4.5 PROPELLER - BLACK (1PAIR/BAG)
,
Counter Rotating Three Blade 6x4.5 Propeller - Black (1Pair/Bag)5 Reviews
HobbyKing
COUNTER ROTATING THREE BLADE 6X4.5 PROPELLER - RED (1PAIR/BAG)
,
Counter Rotating Three Blade 6x4.5 Propeller - Red (1Pair/Bag)5 Reviews
HobbyKing
COUNTER ROTATING THREE BLADE 7X4.5 PROPELLER - BLUE (1PAIR/BAG)
,
Counter Rotating Three Blade 7x4.5 Propeller - Blue (1Pair/Bag)HobbyKing
TURNIGY H.A.L. (HEAVY AERIAL LIFT) HEXCOPTER FRAME 775MM
| Weight | 983g |
| Width | 775mm |
| Motor Bolt Holes | 16/19/25mm |
Specs:, Requires:, 28-XX or 35-XX brushless outrunner motor x 6,
The Turnigy H.A.L. (Heavy Aerial Lift) Hexcopter Frame is crafted ...5 Reviews
HobbyKing
HOBBYKING X930 GLASS FIBER OCTOCOPTER FRAME 895MM
| Width | 895mm |
| Motor Bolt Holes | 16/19/25mm |
Specs:, Frame Weight:, 916g (w/out electronics), Required:, Multi-Rotor control board,
The Hobbyking X930 octocopter frame is a high quality glass ...5 Reviews
ngHobbies
MK3MAG WITH ACC
The following items are included in this kit:, , The MK3MAG requires calibration after installtion. For calibration instructions see the wiki pages:, Calibration istructions,
This item is the 3D compass module for the Mikrokopter ...ngHobbies
HEXA XL POWER DISTRIBUTION BOARD
| • Dimensions | 120 x 120 x 1 mm |
Specifications:, , Documentation:, -,
This is an 6-fold power distribution printed circuit board. Using ...ngHobbies
FLEXIBLE RED LED STRIP
| - Length | 10cm (6 x LED) |
| - Voltage required | 12V |
| - Mounting | remove the protective layer from the bottom to stick it to your MK. |
Technical Data:, Package contains:, One strip of 10cm long felxible red LED strip with 6 LED's on it.,
This is a felxible high output red LED strip. Usually ...ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
FLEXIBLE WHITE LED STRIP
| - Length | 10cm (6 x LED) |
| - Voltage required | 12V |
| - Mounting | remove the protective layer from the bottom to stick it to your MK. |
Technical Data:, Package contains:, One strip of 10cm long flexible white LED strip with 6 LED's on it.,
This is a felxible high output white LED strip. Usually ...ngHobbies
ADXRS610 GYRO BOARD
Documentation:,
This is an assembled ADXRS610 gyro board for the flight ...ngHobbies
BL CONTROLLER CAPACITOR PACK
,
This package contains 10 replacement capacitors for the BL controlers ...