HiModel
2.4G 6-CHANNLE DSM2 MICROLITE PARK FLYER RECEIVER AR6110E (JR/SPEKTRUM COMPATIBLE)
| * Modulation | DSM2 |
| * Band | 2.4 GHz |
| * Dimensions (WxLxH) | 21mm x 28.7mm x 10mm |
| * Weight | 4.0 grams |
| * Voltage Range | 3.5v - 9.6v |
| * Antenna Length | 2 @ 30mm each |
, , , , , , Specifications:, , , , , , , , , , , * # of Channels: 6, How to bind?, 1.with the power off, plug the bind plug into the BATT port., 2.power on the receiver. if powered by a separate battery,plug the battery into any unused port., 3.Position the transmitter's control sticks and switches in the desired fail-safe positions(normally low throttle and all other controls at netural)., 4.press and hold the bind button on the back of the transmitter while turning on the transmitter. the button will flash for several seconds, then the LED on the transmitter and receiver will remain solid on, indicating a successful bind., 5.remove the bind plug to prevent the system form rebinding the next time the power is turned on., , ,
Features: JR/SPEKTRUM Compatible DSM2 2.4G Micro Receiver. Includes/Requires: Includes:1 x ...HiModel
2.4G 9-CHANNLE MICROLITE DSM2 RECEIVER W/ SATELLITE (JR/SPEKTRUM COMPATIBLE)
| ◆ Type | 9-Channel Full-Range DSM2 Receiver |
| ◆ Modulation | DSM2 |
| ◆ Band | 2.4GHz |
| ◆ Dimensions (W x Lx H) | 30 x 50 x 13mm |
| ◆ Weight | 19g |
| ◆ Voltage Range | 4-10v |
| ◆ Brown-Out Voltage | 4.0v (Always supply power above this voltage) |
| ◆ Antenna Length Main RX | 30mm (2) |
, , , , , , Specifications:, , , , , , , , , , , Wireless simulator interface(W.D.S.C), 1. Main receiver and satellite must connect., 2. Receiver must bind with transmitter first (AUX4 channel do not plug binding harness), 3. AUX3 is the (W.D.S.C) channel, connect with simulator line, 4. BIND channel and AUX4 channel plug the binding harness, 5. Apply power to the receiver with USD line or battery, 6. Turn transmitter on, now both LEDS keep light and simulator works, Binding Procedure, 1. Put the binding harness into connector location marked BIND. Next apply power to the receiver. Both receiver and Satellite LED's should illuminate., 2. To set fail-safe throttle and control surface positions, (minimum throttle and all control surfaces set to neutral is suggested). Press and hold the bind button of transmitter (LED will illuminate), Turn on the transmitter., 3. Receiver LED will change from rapid flashing to slow flashing and a few seconds later when bind is accomplished the LED of both satellite and main receiver will illuminate solid. All fail-safes should be programed correctly now., 4. Remove binding harness from the BIND channel. Restart the receiver by cycling it power off and turn on. All channels should function properly now. You may test fail-safe by holding sticks in corner, cycle transmitter on and off. Surfaces and throttle should return to your preset fail-safe positions., General Notes:, Only one bind procedure is required on a new receiver. Repetitive binding provides no extra security. Always remember to remove the binding harness after successful bind is completed., , ,
Features: JR/SPEKTRUM Compatible Key Features ◆ 9 channels ◆ Patent ...1 Reviews
HiModel
2.4G 4-CHANNEL MICROLITE DSM2 /DSMX RECEIVER 4100E (JR/SPEKTRUM COMPATIBLE)
| ◆ Type | 4-Channel Full-Range DSM2 Receiver |
| ◆ Modulation | DSM2 /DSMX |
| ◆ Band | 2.4GHz |
| ◆ Dimensions (L xWx H) | 29x16x7mm |
| ◆ Voltage Range | 3.6-10v |
| ◆ Antenna Length Main RX | 29mm |
| General Notes | This is not a Spektrum receiver, nor is it a copy of a Spektrum Receiver. |
, , , , , , Specifications:, , , , , , , , , , , Receiver Specifications:, ◆ Weight: 3g, Binding Procedure, 1. Put the binding harness into the Channel marked BIND. Next apply power to the receiver. Receiver’s LED should illuminate., 2. To set fail-safe throttle and control surface positions, (minimum throttle and all control surfaces set to neutral is suggested). Press and hold the bind button of transmitter (LED will illuminate), Turn on the transmitter., 3. Receiver LED will change from rapid flashing to slow flashing and a few seconds later when bind is accomplished the LED of receiver will illuminate solid. All fail-safes should be programed correctly now., 4. Remove binding harness from the BIND channel. Restart the receiver by cycling it power off and turn on. All channels should function properly now. You may test fail-safe by holding sticks in corner, cycle transmitter on and off. Surfaces and throttle should return to your preset fail-safe positions., The Spektrum brand is a trademark of Horizon Hobbies USA., , ,
Features: Key Features ◆ 4 channels ◆ Preset failsafe system ...HiModel
2.4GHZ JR DSX3 3-CHANNEL DSM RACING RADIO SYSTEM W/RD350
| Receiver | DSX3 3-Channel DSM |
, , , , , , Specifications:, , , , , , , , , , , Specifications:, , ,
Features: Includes/Requires: Includes: 1 x JR DSX3 transmitter 1 x ...1 Reviews
HiModel
2.4G JR DSX9MK II 9-CHANNEL DSM2 RADIO (BACKLIGHT) W/RD921 RX (NO SERVO)
| -Method | DSM2 |
| -Number of Channels | 9Ch |
| -Transmitter Weight | 810g (excluding battery) |
| - Stick mode | mode 2 (throttle on left hand) will be sent by default, mode 1 is available upon request. |
, , , , , , Specifications:, , , , , , , , , , , * We only accept bank wire transfer (T/T) or western union money transfer for new customers for this product., *, Technical_hints_2.4G.pdf Technical hints on usage of 2.4G radios., , , ,
Features: JR Propo DSX9II Transmitter - Multi-Data Graphic Display with ...HiModel
SWITCH HARNESS W/ FUTABA & JR COMPATIBLE CONNECTORS
| Length | 47cm |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: Switch harness with Futaba & JR compatible connectors. Includes/Requires: ...HiModel
35MHZ BA-R3P6 H/T V3 FM 6-CHANNEL MICRO RECEIVER W/O XTAL
| 4. Weight | 0.19 oz or 5.3g |
| 14. Packing | Shrink wrap |
| 15. Pin direction | horizontal pin |
, , , , , , Specifications:, , , , , , , , , , , 1. Sensitivity：＜2μV, 2. Selectivity：－53dB ±3KHz, 3. Dimensions： 35mmX15mmX10mm(1.38in x 0.59in x 0.39in), 5. Channel：1—6CH, 6. Modulation：FM PPM, 7. Compatibility：PPM transmitter (automatically compatible with positive and negative shift transmitters like Futaba, JR, Hitec, Multiplex, Sanwa, GWS etc.), 8. Effective Receiving ranging：＞300M (＞1000 feet), Note: This is the basic spec of R3PX V3 series receivers; field test could exceed this data due to different radio used. If the field test can not meet this data, please check your radio and crystals., 9. Interference test：Connect the receiver to servo (radio and receiver should be on the same channel). Turn on another radio on an adjacent channel and put it close to the receiver. The receiver should work properly (servo does not glitch at all)., 10. Crystal：UM-5 or UM-1 RX single conversion crystal, 11. Operating current：10mA, 12. Input current：5 V (4-cell) ESC is recommended to power these receivers., 13. frequency： 35M, , ,
Features: ★ BLUEARROW R3Px V3 series micro receivers are upgraded ...HiModel
SPRINGRC 44G / 6.2KG 360° ROBOT SERVO S4306R
, , , , , , Specifications:, , , , , , , , , , , JR interface，360°with Robot Servo,4plastic gears+1metal gear.double ball bearing., , 4.8V, , 6V, , Size (mm), , Weight, , Speed, , Torque, , Speed, , Torque, , A, , B, , C, , D, , E, , g, , oz, , R/M, , kg-cm, , oz-in, , R/M, , kg-cm, , oz-in, , 42.0, , 20.5, , 39.5, , 49.0, , 10.0, , 44, , 1.55, , 60.0, , 5.0, , 69.4, , 50.0, , 6.2, , 86.1, , , ,
Features: JR interface，360°with Robot Servo,4plastic gears+1metal gear.double ball bearing. Includes/Requires: ...3 Reviews
HiModel
HIMODEL 2200MAH 11.1V LITHIUM POLYMER (TX) BATTERY FOR TRANSMITTERS - FLAT
| Size | 100x45x13.5 mm |
| Weight | 124g / 4.38 oz |
| Capacity | 2200mAh |
| Voltage | 11.1V |
| Connector | FUTABA AND JR standard |
, , , , , , Specifications:, , , , , , , , , , , HiModel 2200mAh 11.1V Lithium Polymer (TX) Battery for Transmitters, , ,
Features: Specially designed to use as replacement of TX Ni-Mh/Ni-Cd ...5 Reviews
HiModel
HIMODEL 2200MAH 11.1V LITHIUM POLYMER (TX) BATTERY FOR TRANSMITTERS
| Size | 95x30x18mm |
| Weight | 114g / 4.03 oz |
| Capacity | 2200mAh |
| Voltage | 11.1V |
| Connector | FUTABA AND JR standard |
, , , , , , Specifications:, , , , , , , , , , , HiModel 2000mAh 11.1V 15C Lithium Polymer (TX) Battery for Transmitters, , ,
Features: Specially designed to use as replacement of TX Ni-Mh/Ni-Cd ...2 Reviews
HiModel
MINI USB SIMULATOR INTERFACE CABLE
| ●Supporting system | Windows ME, Windows 2000, Windows XP. |
| http | //n.ethz.ch/student/mmoeller/fms/index_e.html |
, , , , , , Specifications:, , , , , , , , , , , ●Plug and Play., ●USB 1.1/ USB 2.0 Compatible., ●USB interface unit features connectors compatible with most Futaba and JR transmitters., Visit FMS website at, to download simulator software at free of charge, then plug & play., , ,
Features: This is the latest mini size USB type simulator. ...4 Reviews
HiModel
MINI USB SIMULATOR INTERFACE CABLE SIM X12
| http | //n.ethz.ch/student/mmoeller/fms/index_e.html |
Specifications:, ●USB interface unit features connectors compatible with most Futaba and JR transmitters., Visit FMS website at, to download simulator software at free of charge, then plug & play., * Simulator software is NOT included, this is the USB interface with conversion cables only., ,
Features: This is the mini size USB type simulator. The ...HiModel
3.5-7V RX BATTERY VOLTAGE LEVEL LED INDICATOR
| Wire length | 28cm |
| Working voltage | 3.5 to 7V (typically for 4.8V or 6V RX battery) |
| Connector type | Futaba/JR compatible |
| 5V above | green LED |
| 5-4.5V | Green , flash slowly |
| 4.5-4V | Red LED |
| Below 4V | Red LED, quick flash |
, , , , , , Specifications:, , , , , , , , , , , 3.5-7V RX Battery Voltage Level Indicator, Weight: 4g, Working current: , Status:, * This unit can only work under 7V, and can not connect directly to 2S Lipo., , ,
HiModel
GIANT E-RETRACTS SERVOLESS FULL METAL CASE RETRACTABLE LANDING GEAR PZ-15096B (TORQUE 20KG, 7.4V)
| Item No | PZ-15096B |
| Description | Full Metal Case Giant E-retract with Alex |
| Size | 93*51*35(L*W*H) |
| Weight | 173G |
| Speed | 6S/90°@4.8V; 5S/90°@6.0V, 4S/90°@7.4V |
| Torque | 15.5kg-cm@4.8V |
| Operating Voltage | 4.8V-7.4V |
| Landing Struct Diameter | Φ 10mm |
| Support Flight Weight | 10kg-12kg |
| Wire Length | 420mm |
| Wire Color | Brown, Red, Orange |
| Plug Type | JR Plug |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: Features: Smart Build-in Circuit Design After 10 Seconds Auto ...HiModel
FEIYU INERTIAL ATTITUDE STABILIZER FY-30A
| ● Mode 1 | FY-30A Deactivated Mode. In this mode, the FY-30A stabilization function is |
| ● Mode 2 | 3D Control Mode. In this mode, the stabilizer utilizes its 3-axis gyroscope to |
| ● Mode 3 | self-balancing mode. In this mode, the FY-30A will automatically command the |
, , , , , , Specifications:, , , , , , , , , , , Applications, The FY30A can be used in the following fixed wing models:, · Traditional layout fixed-wing aircraft with Aileron, Elevator and Rudder, · Flying wings with rudder;, · Flying wings with no rudder;, · Airplanes with no ailerons (rudder and elevator only), · V-tail airplanes with ailerons;, · V tail airplanes with no ailerons, · Any other configuration, please email us for consultation - feiyudz@yahoo.cn., Remote control system:, The FY-30A has been tested to work well with the following RC system:, · Robbe-Futaba PPM / PCM 1024 / PCM G3 mode, 2.4G systems, · Graupner / JR PPM 8, PPM 12, SPCM mode;, · MPX PPM8, PPM 12 with UNI mode, · any other system with a neutral position of 1.5 ms (standard remote control device)., FY-30A OperatingMode, The FY-30A can be operated in three flight modes modes:, turned off. The aircraft is completely under the control of the pilot., sense roll velocity and flight attitude. If no input is given by the pilot (sticks in the middle, position) the FY30A will hold the current aircraft attitude. This prevents rolling of the, aircraft at the axial plane and maintains its current posture. Therefore the aircraft can be, easily maneuvered to complete a variety of 3D flight with added stability and smoothness., aircraft control surfaces to maintain level flight at all times., The instruction to change the FY30A flight modes is via a spare channel on the RC receiver., , ,
Features: FY-30A is an inertial attitude measurement instrument used for ...2 Reviews