JR HiModel Page 5 Review

HiModel

FY-91Q MULTI-ROTOR FLIGHT STABILIZATION & AUTOPILOT SYSTEM

, , , , , , Specifications:, , , , , , , , , , , FY-91Q Module, Operating voltage ：4.0~6.0 Volt, Current consumption ：50mA (5V input), Dimensions ：55 x 33 x 20 mm, Weight (not including wires) ：20g, Operating Temperature ：-25°C~ +70°C, The maximum allowable rotation rate ： 3 rotations per minute, APPLICABLE AIRCRAFTMODELS, The FY91Q can be installed and flown it the following multi-rotor aircraft:, - 4 motored quadcopters;, - Tri-axial rotory aircraft with 6 motors, - Six-axial multi-rotor aircraft (6 motors), REMOTE CONTROL SYSTEM COMPATIBILITY, FY-91Q have been tested to work with the following RC systems:, · Robbe-Futaba PPM / PCM 1024 / PCM G3 mode, 2.4 GHz systems；, · Graupner/JR PPM 8, PPM 12, SPCM mode；, · MPX PPM8, PPM 12 with UNI mode, · Any remote control system using the standard of 1.5 ms neutral position., , ,

Features: THIS IS FY91Q MODULE ONLY, THE GPS & COMPASS ...

HiModel

STARTER SHAFT W/ ONE-WAY BEARING H0050

, , , , , , Specifications:, , , , , , , , , , , Servo Connector Safety Lock/Clip (5pcs) JR E0023J, , ,

Includes/Requires: Inludes:1 x STARTER SHAFT

HiModel

HOBBYWING HEAD LOCK AVCS GYRO G3

1 Input	4.5-6.5V, operating current = 50mA, maximum current
2 Size	26mm24mm9mm
3 Weight	12g
Analog Servos (frequency 50Hz), servo neutral point	1520us
Digital Servos (frequency 333Hz), servo neutral point	1520us
Note	This gyro is not compatible with following servos

, , , , , , Specifications:, , , , , , , , , , , Specification, 4 Suitable Servo:, Futaba- S9251, S9256, BLS251, JR-2700G, 8700G, 810G, 5 Accessories:, 2 pieces of adhesive foam pads, 1 piece of steel plate for vibration isolation, , ,

Features: 1 Dual working modes: Normal mode and Head-lock mode, ...

HiModel

GWS PG-03 PIEZO GYRO

Size	262711.3mm
Weight	7.0g（0.28oz）
Power Supply	4.8V-6V
Current Draw	10ma（4.8V）
Gain Adjustment	Single rate, non-remote
Operating Temperature	－5�～60�C
Applicable R/C System	FUTABA, JR, SANWA/Airtronics, HI-TEC, Multiplex, GWS etc.

, , , , , , Specifications:, , , , , , , , , , , , ,

Features: The PG-03 has been designed using a new micro ...

HiModel

ZERO TECH YS-X6-P 16-WAYPOINT MULTI-ROTOR FLIGHT CONTROLLER - STANDARD |

* Hint	This system do not support JR radios currently.

, , , , , , Specifications:, , , , , , , , , , , ZERO TECH YS-X6-P 16-waypoint Multi-rotor Flight Controller - Standard, * This is the standard kit, you can buy upgrading package to upgrade to enhanced or professional version., BELOW IS THE LATEST VERSION STRUCTURE OF YS-X6-P, THIS PRODUCT IS THE STANDARD EDITION., , ,

Features: THIS IS THE LATEST P EDITION, YS-X6-P 16-waypoint. New ...

HiModel

SERVOLESS RETRACTABLE LANDING GEAR (METAL STERRING BASE) PZ-15091M

Size(LWH)	73.544.028.0mm 2.891.731.1″
Weight	68g/2.4oz
Speed	0.8s/90°@4.8v 0.6s/90°@6v
Torque	2.7kg-cm@4.8v 3.0kg-cm@6v
Landing Struct Diameter	5mm
Operating Voltage	4.8v-6.0v
Wire Length	150mm
Plug Type	JR Plug

, , , , , , Specifications:, , , , , , , , , , , Servoless Retractable Landing Gear (Metal Steering Base) PZ-15091M, Large Landing Gears with Metal Block, 37.5oz-in@4.8v 41.7oz-in@6v, Support Flight Weight 5kg, , ,

Features: - Integrated design, easy to install, light weight. - ...

HiModel

HV SERVO DIRECT POWER SUPPLY CONNECTOR W/BEC FE-DPC-1

Input	6~8.4v
BEC output current	2A to receiver
Connector type	JR/Futaba compatible
Wire length	30mm
Weight	13g / 0.46oz

, , , , , , Specifications:, , , , , , , , , , , BEC output voltage: 5V, This version has one servo output, and one receiver output., * The receiver output must connect to the matching channel of the servo, for example, if the servo is for elevator, then the receiver connector should be plugged to the RX elevator channel., , ,

Features: Typical application: Use one 2S lipo to power a ...

HiModel

4-WAY HV SERVO DIRECT POWER SUPPLY CONNECTOR W/BEC FE-DPC-4

Input	6~8.4v
BEC output current	2A to receiver
Connector type	JR/Futaba compatible (4 connectors for servos, 4 connectors to receiver)
Wire length	30mm
Weight	32g / 1.13oz

, , , , , , Specifications:, , , , , , , , , , , BEC output voltage: 5V, This version has 4 servo outputs., Wiring hint: simply plug the 4 servos to the servo outputs, and connect the matching RX connectors to the relative channels., , ,

Features: Typical application: Use one 2S lipo to power a ...

HiModel

XQ-POWER 56G/16KG/ .12SEC 6-7.2V METAL GEAR DIGITAL SERVO XQ-S3015D

Speed	0.16 sec/60° @ 6V; 0.12 sec/60° @ 7.2V
Torque	15kg-cm @ 6V; 16kg-cm @ 7.2V
Weight	56g / 1.46oz
Power Supply	6V/ 7.2V
Connector type	JR/Futaba compatible

, , , , , , Specifications:, , , , , , , , , , , Dimension (mm): A: 40.8, B: 20.1, C: 38, D: 48.5, E: 10, , ,

Includes/Requires: Includes:1 x servo 1 x servo horn set

HiModel

XQ-POWER 25G/2.9KG/ .09SEC DIGITAL SERVO XQ-S1016D

Speed	0.13 sec/60° @ 4.8V; 0.11 sec/60° @ 6V
Torque	2.5kg-cm @ 4.8V; 2.9kg-cm @ 6V
Weight	16g / 0.42oz
Power Supply	4.8V/ 6V
Connector type	JR/Futaba compatible

, , , , , , Specifications:, , , , , , , , , , , Dimension (mm): A: 22.8, B: 12.6, C: 24.8, D: -, E: -, , ,

Includes/Requires: Includes:1 x servo 1 x servo horn set

HiModel

FITEC 56G/ 12.5KG/ .12 SEC TITANIUM GEAR DIGITAL SERVO FS5513M

Dimension	40.2 x20.0 x38.6mm
Weight	56g (1.46oz)
Speed	0.14sec/60°（4.8V）
Torque	10.5kg.cm/146.7 oz.in（4.8V）
Working voltage	4.8-6V
Dead band width（usec）	2usec
Connector type	JR/Futaba compatible
Wire length	30cm
Application	airplane, car, boat

, , , , , , Specifications:, , , , , , , , , , , SPECIFICATION：, .12sec/60°（6V）, 12.5kg.cm/173.6 oz.in（6V）, , ,