FPV Equipment, First Person View, RC FPV Page 15 Review

HiModel

FRSKY AMPERE SENSOR FAS-100

Model	FAS-100
Dimension	38 x 30 x 10mm
Weight	24g
Measurement range	0-100A
Maximum safe current	100A
Sensor current consumption	33mA
Update rate	≥1Hz

, , , , , , Specifications:, , , , , , , , , , , * When use the amp sensor FAS-100 with a sensor hub, please make sure your sensor hub firmware is V2.0., , ,

Includes/Requires: Includes:1 x amp sensor

HiModel

FRSKY TWO-WAY 2.4G DHT MODULE - TOGGLE SWITCH VERSION

Operating Voltage Range	6.0V-13.0V
Operating Current	50mA
Output Power	60mW
Resolution	3072 (>11bit)

, , , , , , , , Features:, , , , , , , , , , , THIS IS THE NEW TOGGLE SWITCH VERSION DHT., 1.1 Compatibility:, Switch 1, , Switch 2, , Mode of DHT, , Compatibility, , OFF, , OFF, , Two-way Mode, , Two way telemetry receivers (D8R, D6FR), , OFF, , ON, , V8 Mode, , V8 receivers (V8FR-HV, V8R7-HV, V8R7-SP, V8R4), , 1.2 Specifications:, 2. Setup, 2.1 Installation process:, 1）Open the transmitter, find out Battery power supply line, PPM signal line, and GND., 2）Take the order and solder Battery power supply line, PPM signal line, and GND to DHT with 3 wires., (RED→V+; BLACK→GND; YELLOW→PPM), 3）Drill one hole on the transmitter to install the PCB with F/S button, GREEN/RED LED and two switches., 4）Connect the antenna connector at the port on transmitter board., 5）Drill a hole for antenna connector at suitable space on the transmitter (diameter 7mm is suitable)., 6）Fix the transmitter antenna on the connector .Turn the transmitter power on and check the power indicator LED, which is normally light RED., 2.2 Bind procedure, 1）Turn your transmitter on and switch it to PPM mode. Turn your transmitter off., 2） Turn your transmitter on while holding the F/S button on the transmitter module (Please make sure DHT is in its corresponding mode when working with V8 or two way telemetry receivers). Release it in a few seconds. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver., 3）Connect battery to the receiver while holding the F/S button on the receiver. The RED LED on the receiver will flash, indicating the binding process is completed., 4）Turn on the transmitter and re-connect battery to the receiver. The RED SOLID LED on the receiver will indicate the receiver is receiving commands from the transmitter., 5）After the above steps are completed, both the transmitter and the receiver are ready to be used., Notice: When working with two way telemetry receivers (D8R or D6FR), please kindly make sure that the battery ,

Features: THIS IS THE NEW TOGGLE SWITCH VERSION DHT. 1.1 ...

1 Reviews

HiModel

FRSKY LIPO BATTERY VOLTAGE SENSOR W/O LED DISPLAY FLVS

, , , , , , Specifications:, , , , , , , , , , , Battery Voltage Sensor, FrSky Lipo Battery Voltage Sensor (without LED Display) for FrSky Two-way Telemetry System, , ,

Features: This is the simplified version of FLVS-01. Includes/Requires: Includes: ...

HiModel

D24XD8XL65MM LANDING SKID SPONGE SHOCK ABSORBING & PROTECTION SLEEVES (4PCS)

Outer diameter	24mm
Inner diameter	8mm
Length	65mm
Weight	2.3g (each)

Specifications:, Landing Skid Sponge Shock Absorbing & Protection Sleeves - Red & Black (4pcs), ,

Features: Typical application: Put the sponge sleeves around the landing ...

HiModel

D24XD8XL45MM LANDING SKID SPONGE SHOCK ABSORBING & PROTECTION SLEEVES (4PCS)

Outer diameter	24mm
Inner diameter	8mm
Length	45mm
Weight	3.2g (each)

Specifications:, Landing Skid Sponge Shock Absorbing & Protection Sleeves - Red & Black (4pcs), ,

Features: Typical application: Put the sponge sleeves around the landing ...

HiModel

3K GLASSY CARBON SHOCK ABSORBING PLATE A4 W/4 DAMPING BALLS (SUIT FOR GOPRO ETC.)

Dimension	85 x 70 x 20mm
Material	3K Glassy Carbon
Plate thickness	1.2mm
Suitable camera	Gopro or similar size card type cameras
Weight	25g

Specifications:, 3K Glassy Carbon Shock Absorbing Plate A4 W/4 Damping Balls (suit for Gopro etc.), Damping ball number: 4, * Not pre-assembled., ,

Features: Application: Hooked between multi-rotor craft and gimbal, eliminates vibration ...

HiModel

3K CARBON FIBER SHOCK ABSORBING PLATE A24 W/24 DAMPING BALLS (SUIT FOR 5-8KG GIMBAL)

Material	3K Glassy Carbon
Plate thickness	2mm
Suitable camera	5-8Kg gimbal
Weight	115g

Specifications:, 3K Carbon Fiber Shock Absorbing Plate A24 W/24 Damping Balls (suit for 5-8Kg Gimbal), Dimension:, Φ141, x 20mm (approx.), Damping ball number: 24, * Not pre-assembled., ,

Features: Application: Hooked between multi-rotor craft and gimbal, eliminates vibration ...