HiModel
CYCLOPS NOVA OSD FIRMWARE UPGRADER
Features:, , Includes/Requires:, , Includes:, 1 x firmware upgrader for NOVA OSD,
This is the firmware upgrader for Nova OSD system from ...HiModel
HIMODEL 5.8G 4-WAY DIVERSITY A/V RECEIVER (RX) D58-4 | SMA, JACK
| CH1 | 5705MHz CH2 |
| CH5 | 5885MHz CH6 |
| Video Output | 75Ω/1Vpp |
| Audio Output | 10KΩ/500mVpp |
| TV System | PAL/NTSC/SECAM |
| Input Voltage | 12V/500mA |
| - Connector type | SMA Jack (on the receiver side) |
, , , , , , Specifications:, , , , , , , , , , , 1. Specification:, Receiver Frequency:, Refer to here for connector type diagram, , ,
Features: Four Receiver for best reception Automatic Antenna ...HiModel
FPV 5.8G 200MW A/V TRANSMITTING/RECEIVING SYSTEM | RP-SMA, JACK
| Transmitting unit weight | 34.5g |
| Power input | 12V ± 5% |
| Receiving current | 100mA |
| Transmitting current | 100mA |
| Transmitter Channel number | 8-ch |
| Receiver channel number | 4-ch |
| Antenna gain | 3db |
| Video signal resistance | 75Ω |
| Antenna connection | RP-SMA jack (both TX/RX modules, module side) |
| CH1 | 5705 CH2 |
| CH3 | 5665 CH4 |
| CH5 | 5885 CH6 |
| CH7 | 5925 CH8 |
, , , , , , Specifications:, , , , , , , , , , , FPV 5.8G 200mW A/V Transmitting/receiving System, Refer to here for connector type diagram, Details of channel frequencies of the transmitter:, *Note: TX antenna must be installed properly before it is switched on, power on without install antenna, or a improper antenna was used may easily burn the TX, and such damage is not covered by warranty., , ,
Features: FPV 5.8G 200mW A/V Transmitting/receiving System, a good choice ...11 Reviews
HiModel
FPV 5.8G 400MW A/V TRANSMITTER MODULE (TX) ｜SMA, JACK
| Transmitting unit weight | 35g (excluding antenna) |
| video format supported | NTSC/PAL |
| Working frequency | 5645-5945Mhz |
| Power input | 7-15V (3S Lipo suggested, does NOT support 4S Lipo) |
| Transmitting current | 220mA |
| Dimension | 55*26*17mm (excluding antenna) |
| Antenna connection | SMA jack (TX module side) |
, , , , , , Specifications:, , , , , , , , , , , FPV 5.8G 400mW A/V Transmitter Module (TX), Refer to here for connector type diagram, * This product shares the PCB board with the 1000mW version, you may see letters "TX51W-power...." on the PCB board, this is not a mistake. There is no cooling fan on the 400mW version which is a obvious difference., *Note: TX antenna must be installed properly before it is switched on, power on without install antenna, or a improper antenna was used may easily burn the TX, and such damage is not covered by warranty., , ,
Features: FPV 5.8G 400mW A/V Transmitting module, a good choice ...HiModel
FEIYU HORNET OSD W/CURRENT SENSOR FY-OSD
, , , , , , Specifications:, , , , , , , , , , , FEIYU Hornet OSD FY-OSD, , ,
Includes/Requires: Includes:1 x FY-OSD 1 x current sensor 1 x ...HiModel
AP117 ON SCREEN DISPLAY (OSD) AP117
, , , , , , Specifications:, , , , , , , , , , , , ,
Includes/Requires: Includes:1 x AP117 OSDHiModel
G.T.POWER FPV 5.8G 250MW A/V TRANSMITTING MODULE (TX) ｜RP-SMA, JACK
| Video Format | Pal/NTSC |
| Output impedance | 50 Ohm |
| Output power | 21-23 dBm |
| Transmitter operating voltage | 7.4-12.6 V DC/200mA |
| Video bandwidth | 0-8.0 MHZ |
| Audio input impedance | 10K/Ohm |
| Audio input level | 0.5-2.0 Vp-p |
| Audio frequency | 6.5 MHZ |
| Antenna connector | RP-SMA, jack (TX side) |
| Video input level | 0.8-1.2 Vp-p |
| Video input impedance | 75 Ohm |
| Dimensions | 55x26x17 mm |
| Weight | 25 g |
, , , , , , Specifications:, , , , , , , , , , , Channels: 8, See connector type diagram, , ,
Includes/Requires: Includes: 1 x transmitting unit 1 x basic wires1 Reviews
HiModel
FPV 5.8G A/V RECEIVER (RX) RC305 | RP-SMA, JACK
| Receiving current | 100mA |
| Receiver channel number | 8-ch |
| Power input | 12V +/- 5% |
| Antenna connector | RP-SMA jack (module side) |
, , , , , , Specifications:, , , , , , , , , , , FPV 5.8G A/V receiving unit RC305, Refer to here for connector type diagram, , ,
Features: This is the A/V receiving unit only, a good ...2 Reviews
HiModel
FPV 5.8G A/V RECEIVER (RX) W/CHANNEL NUMBER DISPLAY RC805 | RP-SMA, JACK
Features:,
THIS IS THE NEW VERSION WITH CHANNEL NUMBER DISPLAY. This ...2 Reviews
HiModel
MFD AUTOMATIC ANTENNA TRACKER (AAT) SYSTEM - STANDARD COMBO
| Includes | TeleFlyOSD x 1 |
Features:, , What makes the MyFlyDream Tracking System so special:, - The high quality slipring provides endless rotation, meaning endless freedom, you will never again temporarily loose your signal because the tracker has reached its maximum rotation angle and is turning over to the other side., Includes/Requires:, ,
The standard combo contains everything you need to set up ...HiModel
MFD 10HZ GPS MODULE (COMPATIBLE WITH CYCLONE OSD) LS20033
| Includes | 1 x GPS module |
Features:, , Includes/Requires:, ,
LS20030~3 series products are complete GPS smart antenna receivers, including ...HiModel
5.8G 16DBI HIGH GAIN RECEIVING PLATE ANTENNA
| Dimension | 23.5x 19.5x 3.5cm |
| Weight | 405g |
| Working Frequency | 5180-5850Mhz |
| Connector type | SMA (inner thread) |
| Wire length | 29cm |
| Mounting screw diameter | 5mm |
, , , , , , Specifications:, , , , , , , , , , , 5.8G 16dbi High Gain Receiving Plate Antenna, standing wave ratio: , , ,
Features: Compatible with MFD Automatic Antenna Tracker (AAT) System. Includes/Requires: ...HiModel
FRSKY GPS MODUEL GPS-01
| Longitude | dddmm.mmmm E/W |
| Latitude | ddmm.mmmm N/S |
| Installation | Use double-sided tape to install the GPS on any appropriate surface of the airframe. |
| Note | Up right position is recommended. |
, , , , , , Specifications:, , , , , , , , , , , GPS feedbacks various data, such as speed, longitude and latitude., Note:, , ,
Features: Different sensors facilitate to monitor different data, such as ...HiModel
FRSKY TEMPERATURE SENSOR TEMS-01
| Accuracy | 1 degree Celsius/ 1 degree Fahrenheit |
, , , , , , Specifications:, , , , , , , , , , , Up to two temperature sensors can be used at the same time. They are commonly used to read temperatures of model accessories, such as electric motor, ESC, glow and gas engine cylinder head, battery, muffler, voltage regulator, BEC, tailpipe and ambient air. Measurement Range: -30~250 degrees Celsius/ -22~482 degrees Fahrenheit, Installation: Use zip ties to hold the temperature sensor tightly against the accessory that requires temperature reading., , ,
Features: Different sensors facilitate to monitor different data, such as ...