HiModel
HV SERVO DIRECT POWER SUPPLY CONNECTOR W/BEC FE-DPC-1
| Input | 6~8.4v |
| BEC output current | 2A to receiver |
| Connector type | JR/Futaba compatible |
| Wire length | 30mm |
| Weight | 13g / 0.46oz |
, , , , , , Specifications:, , , , , , , , , , , BEC output voltage: 5V, This version has one servo output, and one receiver output., * The receiver output must connect to the matching channel of the servo, for example, if the servo is for elevator, then the receiver connector should be plugged to the RX elevator channel., , ,
Features: Typical application: Use one 2S lipo to power a ...HiModel
SKYWALKER 2-4S 40A ELECTRIC SPEED CONTROL (ESC) 40A-UBEC
| Type | SKYWALKER-40A-UBEC |
| · Weight | 43g |
| · Size | 68 x25 x12 mm |
| · Constant Current | 40A |
| · Max Current | 55A (for ten seconds) |
| · BEC | Yes, 3A / 5V |
| · Input | 2 to 4 Li-Po, or 5 to 12 Ni-MH/Ni-Cd |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: The SKYWALKER Series ESCs are produced by well known ...1 Reviews
HiModel
HIMODEL FLYHYPER 2-4S 30A ELECTRIC SPEED CONTROL (ESC) FH-30A
| Type | FH-30A |
| Weight | 30g |
| Size | 54x25x11 mm |
| Constant Current | 30A |
| Max Current | 40A (for ten seconds) |
| BEC | Yes, 3A / 5V |
| Input | 2 to 4 Li-Po, or 5 to 12 Ni-MH/Ni-Cd |
| Brake Setting | On/Off, the default is off; |
| Setting for battery type | LiPo (lithium) or NiCd/ NiMh (nickel metal hydride / nickel at), the default is LiPo |
| Low-voltage protection threshold setting | low / medium / high, the default is medium (3.0v/65%); |
| Motor timing setting (increase the efficiency and the start stability of the electronic governor) | low/medium/high, the default is medium (3.0v/65%); |
| Accelerated startup setting (for precision gearboxes and helicopters) | (provide the rapid accelerated startup with linear throttle response), the default is soft; |
| Motor steering (clockwise / counterclockwise) | forward steering / reverse steering, the default is forward steering; |
| PWM operating frequency | 8KHz/ 16kHz, the default is 8KHz; |
| Low voltage protection modes (lower power or stop immediately) | lower power / immediately stop, the default is lower power. |
, , , , , , Specifications:, , , , , , , , , , , Helicopter mode (for helicopters), the default is off;, , ,
Features: - With helicopter mode, can be used for both ...1 Reviews
HiModel
HIMODEL COOL SERIES 13A BRUSHLESS SPEED CONTROLLER 13A/LBEC
| Type | 13A/LBEC |
, , , , , , Specifications:, , , , , , , , , , , HiModel COOL ESCs for Airplanes/Helicopters, , Type, , Continious Current（A）, , Max Current（A）, , Lipo Cell Number, , BEC Mode, , BEC Volt/Current, , Weight, , Dimension (LxWxH)mm, , COOL 6A/LBEC, , 6A, , 7A, , ２, , Linear Mode, , 5V/0.8A, , 4g, , 25*12*4, , COOL 11A/LBEC, , 11A, , 13A, , ２- 3, , Linear Mode, , 5V/2A, , 10G, , 25*17*3, , COOL 13A/LBEC, , 13A, , 16A, , ２- 3, , Linear Mode, , 5V/2A, , 12g, , 25*17*5, , COOL 22A/SBEC, , 22A, , 25A, , ２- 4, , Switch Mode, , 5.0V/4A, , 27g, , 32*24*11, , COOL 33A/SBEC, , 33A, , 40A, , ２- 4, , Switch Mode, , 5.0V/4A, , 29g, , 32*24*11, , COOL 41A/SBEC, , 41A, , 50A, , ２- 4, , Switch Mode, , 5.0V/4A, , 35g, , 32*24*11, , COOL 44A/SBEC, , 44A, , 55A, , ２- 6, , Switch Mode, , 5.5V/6A, , 55g, , 51*31*12, , COOL 66A/SBEC, , 66A, , 80A, , ２- 6, , Switch Mode, , 5.5V/6A, , 57g, , 51*31*12, , COOL 88A/SBEC, , 88A, , 110A, , ２- 6, , Switch Mode, , 5.5V/6A, , 63g, , 51*31*13, , COOL 110A/SBEC, , 110A, , 150A, , ２- 6, , Switch Mode, , 5.5V/6A, , 74g, , 51*31*13, , COOL 155A/SBEC, , 155A, , 200A, , ２- 6, , Switch Mode, , 5.5V/6A, , 79g, , 52*31*17, , Program Card III, , , , , , , , , , , , 10g, , , , , ,
Features: HiModel COOL Series Brushless Speed Controller for airplane/helicopter etc. ...1 Reviews
HiModel
HIMODEL 50A 2-7S BRUSHLESS SPEED CONTROLLER FOR HELICOPTERS W/ULTRA BEC TYPE GX-H50A-BEC
| Type | GX-H50A-BEC |
| · Weight | 41 g / 1.46 oz (with separate BEC unit) |
| · Size | 45 X 36 X 9（mm） |
| · Constant Current | 50A |
| · Max Current | 60A (for ten seconds) |
| · BEC | 3A at 5V |
| · PWM | 8KHZ/16KHz |
| · Input | 2 - 7 Lipo |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: ●Auto detect the cells and type of batteries, and ...1 Reviews
HiModel
HIMODEL GX SEIRES 50A 2 - 7S BRUSHLESS ELECTRIC SPEED CONTROLLER TYPE GX-50A
| Type | GX-50A |
| · Weight | 40g / 1.41 oz |
| · Size | 46 x 35 x 8 mm |
| · Constant Current | 50A (under good cooling environment) |
| · Max Current | 60A (for ten seconds) |
| · BEC | No (you need a separate RX battery or a external BEC unit to power the receiver and servos) |
| · PWM | 8 Khz/ 16Khz |
| · Input | 6 - 20 Ni-Mh/Ni-Cd or 2 - 7 Lipo |
, , , , , , Specifications:, , , , , , , , , , , · FET No.: 12, * This ESC does not have BEC output, you need a separate RX battery or a external BEC unit to power the receiver and servos., , ,
Features: ●Auto detect the cells and type of batteries, and ...1 Reviews
HiModel
HIMODEL GX SEIRES 70A 3 - 7S BRUSHLESS ELECTRIC SPEED CONTROLLER W/BEC TYPE GX-70A-BEC
| Type | GX-70A-BEC |
| · Weight | 65g / 2.29 oz |
| · Size | 68 x 35 x 12 mm |
| · Constant Current | 70A (under good cooling environment) |
| · Max Current | 90A (for ten seconds) |
| · BEC | switch mode 3-7S, 5A |
| · PWM | 8 Khz/ 16Khz |
| · Input | 8 - 20 Ni-Mh/Ni-Cd or 3 - 7 Lipo |
, , , , , , Specifications:, , , , , , , , , , , · FET No.: 18, , ,
Features: ●Auto detect the cells and type of batteries, and ...8 Reviews
HiModel
HIMODEL 6-50V INPUT 20A LARGE CURRENT SWITCHING MODE VOLTAGE REGULATOR/ SBEC
| Input | 6 - 50.4 V |
| Output voltage | 5V/5.5V/6V/7V/9V (jumper selection) |
| Current | 20amps continuous/ 25amps peak (2 seconds) |
| Mode | Switch-mode |
| Quiescent current | 60uA to 200uA |
| Size | 59 x 26 x 22mm |
| Weight | 45g/ 1.57oz |
, , , , , , Specifications:, , , , , , , , , , , HiModel 20A SBEC, , ,
Includes/Requires: Includes:1 x SBEC3 Reviews
HiModel
HIFEI KINGKONG SERIES 2-6S 45A ELECTRIC SPEED CONTROL W/DATA LOGGER ESC-45A-K
| Type | ESC-40A-K |
| Size | 58mm X 26mm X 17mm |
| Weight | 40g |
| Constant Current | 45A (65A burst) |
| BEC | Yes, 3.5A switch mode |
| Input | 2 to 6S Li-Po |
| Data logging function | YES |
| Programing methods | Program card/Program box/USB Linker capable (not included) |
, , , , , , Specifications:, , , , , , , , , , , Resources:, Software, , Instruction Manual, , , ,
Features: 1. Microprocessor controlled 2. Integrated the function of flying ...HiModel
HIFEI KINGKONG SERIES 2-6S 60A ELECTRIC SPEED CONTROL W/DATA LOGGER ESC-60A-K
| Type | ESC-60A-K |
| Size | 71mm X 26.5mm X 15mm |
| Weight | 48g |
| Constant Current | 60A (70A burst) |
| BEC | Yes, 3.5A switch mode |
| Input | 2 to 6S Li-Po |
| Data logging function | YES |
| Programing methods | Program card/Program box/USB Linker capable (not included) |
, , , , , , Specifications:, , , , , , , , , , , Resources:, Software, , Instruction Manual, , , ,
Features: 1. Microprocessor controlled 2. Integrated the function of flying ...HiModel
ICE SERIES 100A 2-6S BRUSHLESS SPEED CONTROL FOR AIRPLANE/HELICOPTER TYPE FLY 100A-ICE SB
| Type | FLY 100A-ICE SB |
| Size | 72 x 32.8 x 14 mm |
| Constant Current | 100A |
| Max Current | 120A for 10 seconds |
| Input Voltage | 2-6 cells li-XX or 6-16 Ni-MH/Ni-Cd battery |
| BEC | yes, Switch BEC |
| BEC Output | 5.5V/6A |
| PWM | 8-16 KHz |
| Max RPM | 240,000rpm for 2 Poles Brushless Motor |
| Weight | 69g |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: * Compatible with a programming card to change and ...3 Reviews
HiModel
ICE SERIES 120A 4-14S ESC FOR AIRPLANE/HELICOPTER TYPE FLY 120A-ICE HV
| Type | FLY 120A-ICE HV |
| Constant Current | 120A |
| Max Current | 140A for 10 seconds |
| Input Voltage | 4-14 cells li-XX or 12-42 Ni-MH/Ni-Cd battery |
| BEC | none, OPTO |
| BEC Output | none |
| PWM | 8-16 KHz |
| Max RPM | 240,000rpm for 2 Poles Brushless Motor |
| Size | 85mm x 53mm x 30mm |
| Weight | 102g |
, , , , , , Specifications:, , , , , , , , , , , *This ESC is OPTO version and does not have BEC output, which means you need a separate RX battery pack or external BEC unit to power the receiver and servos., , ,
Features: * Compatible with a programming card to change and ...8 Reviews
HiModel
FLY PRO SEIRES 25A 2-4S BRUSHLESS SPEED CONTROL TYPE FLY-25A-PRO SB
| · Weight | 26 g |
| · Size | 46 x25 x9 mm |
| · Constant Current | 25A |
| · BEC | Switch mode 5.5V/ 3A |
| · PWM | 8 KHz |
| · Input | 2 to 4 Li-Po/ 6-12 NiCd/NiMh |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: ● Super fine and smooth touch of speed controlling, ...1 Reviews
HiModel
HIMODEL FLY SEIRES 4 - 10S 100A ELECTRIC SPEED CONTROLLER FOR HELICOPTER TYPE HV HELI-100-OPTO
| Type | HV Heli-100-OPTO |
| · Weight | 326 g / 11.5 oz |
| · Size | 151 x60 x30mm |
| · Constant Current | 100A |
| · Max Current | 120A (for ten seconds) |
| · PWM | 8/16/32 KHz |
| · Input | 4 to 10 Li-Po or 10 - 32 Ni-Mh/Ni-Cd. |
, , , , , , Specifications:, , , , , , , , , , , · BEC:NO, *This ESC is OPTO version and does not have BEC output, which means you need a separate RX battery pack or external BEC unit to power the receiver and servos., , ,
Features: HiModel FLY Seires Brushless Speed Control With Governor function ...HiModel
HIMODEL 3350KV BRUSHLESS MOTOR 2.3MM SHAFT B2040-7T
| Model | B2040-7T |
| Voltage Range | 11.1V |
| No Load Current(A) | 0.9 |
| Resistance | 0.085Ω |
| Kv(Rpm/V) | 3350 |
| Can diameter | 20 mm |
| Can length (without front/rear cover protrusion) | 42mm |
| Can length with front/rear cover | 47mm |
| Weight(g) | 60g |
| Shaft diameter | Φ2.3 mm |
| Shaft length | 9.4mm |
| Max Efficiency | 82% |
| Max Power | 165 W/60S |
, , , , , , Specifications:, , , , , , , , , , , Max Efficiency Current(A):20, Max Load Current (A/60S):23, , ,
Includes/Requires: Includes:1 x brushless motor1 Reviews