ngHobbies
XBEE TELEMETRY KIT
The following items are included with this product:, 1 of XtreamBee Board (No XBee included), In this kit you will find everything you need to add telemetry features to your aircraft set up. The Xbee modules come paired up and ready to use! Included with this kit:, 1 x XtreamBee Board (The one manufactured by DIYDrones!), including the two female connectors and right angle connectors., For setup instructions:, Click here,
1 of XtreamBee USB Adapter 1 of Xbee-Oil Pan connector ...ngHobbies
EM-406/UBLOX/MTK ADAPTER CABLE 15CM
,
This is a communication cable, 15 centimeters, that mates with ...ngHobbies
ARDUINO PRO MINI 328 - 3.3V/8MHZ
Please note: Arduino 0015 supports the ATmega328 but not yet at 8MHz. Please select 'Arduino Duemilanove w/ 328' within the Arduino software but expect your delays to work twice as long (Code will run half as fast as the Duemilanove is at 16MHz)., FEATURES:, ATmega328 running at 8MHz with external resonator (0.5% tolerance),
It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! ...ngHobbies
ARDUPILOT MEGA 2.5+ FULLY ASSEMBLED SYSTEM
Features:, Arduino Compatible!, :, ArduPlane code, :, MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking™,
The ArduPilot Mega 2.5 is a complete open source autopilot ...ngHobbies
DF13 6 POSITION TO 5 POSITION CONNECTOR 15 CM
,
This communication cable uses the Hirose DF13 series connector. It ...ngHobbies
3DR RADIO TELEMETRY KIT - 915 MHZ
The 3DR Radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. It’s available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground)., Documentation and Manuals:, 3DR Radio Configurator,
The system provides a full-duplex link using HopeRF's HM-TRP modules ...ngHobbies
AIRSPEED KIT WITH MPXV7002DP
| Weight | 0.1 oz; 4 g (Just the sensor) |
The MPXV7002 is designed to measure positive and negative pressure. In addition, with an offset specifically at 2.5V instead of the conventional 0V, this new series allows to measure pressure up to 7kPa through each port for pressure sensing but also for vacuum sensing (refer to the transfer function in the data sheet for more detailed information). Features: -2 to 2 kPa (-0.3 to 0.3 psi). 0.5 to 4.5 V Output,
This is a stand-alone airspeed sensor. Includes Pitot Tube and ...ngHobbies
ARDUPILOT MEGA MINIMOSD REV. 1.1
| Dimensions | 0.7"W x 1.7"L (2.4" w/ pins as shown) x 0.3"H |
| NOTE | This product is not compatible with the APM 2.0. |
It features two independent power and ground sections to isolate the OSD's analog stage:, a +5V section for the ATmega and the OSD's digital stage, powered through the FTDI cable or other +5V source; and a regulated +5V section for the OSD's analog stage, powered through the video in/out header and capable of handling up to +12V input. Solder jumpers are available to combine the two power and ground sections if desired., Set up instructions:, click here to download or open,
MinimOSD, a minimal Arduino-based on-screen display board. It's tailored for ...ngHobbies
I2C/SMBUS VOLTAGE TRANSLATOR (I2C LEVEL SHIFTER)
Features:, I2C and SMBus compatible, Resources:, TI PCA9306 Datasheet,
This great tiny board will allow to interface slave 3.3V ...ngHobbies
ARDUPILOT MEGA 2.5 CASE, TOP ENTRY
The new APM 2.5 enclosure is made of black translucent ABS plastic. It protects your electronics while allowing access to all pins and connectors. The inside of the enclosure is lined with ESD safe open cell foam to ensure the barometric pressure sensor is surrounded by static air and prevent unwanted readings due to airflow over the sensor. The screws that secure the enclosure have been moved to the top for ease of use. The enclosure comes in two variants: top entry and side entry., Assembly Instructions:, Click here, NOTE:, This product is compatible with APM 2.5 only! The ArduPilot Mega 2.5 board is not included, it's included in the image only as a reference.,
This is the official case for the APM 2.5 system. ...ngHobbies
ARDUPILOT MEGA 2.6+ FULLY ASSEMBLED SYSTEM
Features:, Arduino Compatible!, :, ArduPlane code, :, MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking™,
The ArduPilot Mega 2.6 is a complete open source autopilot ...ngHobbies
ARDUSTATION
Please note:, Assembly required., Atmega328 at 16Mhz with Arduino Bootloader. XBee Socket and 3.3V powered (I've included some holes near to the antenna so you can hold it with a strap). Wireless programing: You can use XBEE to program it (needs 2n2222 transistor available at any radioshack). Can be powered with 2 and 3 cell LIPOS (diode protected and regulated). Huge 4 line screen with backlight, very clear under the sun! (2 pots to control the backlight and contrast). FTDI port to upload code, also the boards is ready to be programmed with XBee. Six button to navigate and change screen and options. Very noisy buzzer that can be used to alert you when it has low battery or low altitude. 6 I/O analog pins available, including the I2C port. 2 powered SERVO OUTPUTS (Tilt & Pan) that can be used to control a directional antenna (NICE!). Extra 3.3V and 5V volts outputs. Status LED's., Documentation:, -,
New portable open source ground station (Arduino and xBee based) ...