ReadyMadeRC
GAUI 330X-S QUAD FLYER KIT W/ SCORPION MOTORS W/O GU-344 GYRO
| 5. System Extensibility | can be used with GPS positioning system and navigation system on 330X without any change |
| *The actual of Cruise data with full payload(The safety flight time | 1332/170X75%=5.88min) |
| Gaui 330X Quadcopter | Part One |
330X was designed based on UAV , which emphasizes the advantages are:, 1. Flight Efficiency: Standard Battery (2S2000mAh) time of flight for more than 12min, with a high-capacity battery, the flight time will be more than 20 min or more (available spreadsheet calculation), 2. Excellent wind resistance: the efficiency and load of propeller are perfectly optimized, so the wind resistance will be better than general electric aircraft, 3. High stability: contains GU344 (three-axis stabilizing system) for the beginner or the FPV flying, it is a very stable Vehicle, 4. Additional payload capabilities: payload up to 700g (including battery), can freely install cameras and video recorder, and other general system, Videos of 330X:, ,
The 330X Quad-Flyer This version comes without the GU-344 Gyro, ...ReadyMadeRC
TWINSTAR FPV PAN/TILT POD KIT
| Manual | TwinStarPod.pdf |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, RMRC-420, RMRC-420XV, RMRC-520, RMRC-LL600, KX131, KX171, KX191, IF Cam, SN777, SN555 and others, Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900 servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
A TwinStar FPV pod that uses a custom mechanism allowing ...ReadyMadeRC
SKYWALKER FPV PAN/TILT POD KIT
| Manual | HERE |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for TG9e servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
An FPV pod for the SkyWalker that offers a custom ...ReadyMadeRC
RADIAN FPV PAN/TILT POD KIT
| Manual | HERE |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900/TG9e servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
A Parkzone Radian and Radian Pro FPV pod that uses ...ReadyMadeRC
EASY GLIDER FPV PAN/TILT POD KIT
| Manual | EasyGliderPod |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, RMRC-420, RMRC-420XV, RMRC-520, RMRC-LL600, KX131, KX171, KX191, IF Cam, SN777, SN555 and others, Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900 servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
An Easy Glider FPV pod that uses a custom mechanism ...ReadyMadeRC
SKY SURFER FPV PAN/TILT POD KIT (FITS BIXLER V1)
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, , Other options include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for TG9e or HS-65HB servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, , Manual:, Sky Sufer Pod Instructions,
A Sky Surfer FPV pod that uses a custom mechanism ...ReadyMadeRC
EASY STAR FPV PAN/TILT POD KIT
| Manual | EasyPod |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900 servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
An Easy Star FPV pod that uses a custom mechanism ...ReadyMadeRC
CAMERA PAN AND TILT KIT
| Manual | Pan/Tilt Module |
Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., Comes with a mounting plate that will fit many popular FPV cameras including:, , Note: Currently the back plates are designed for the pan/tilt system being installed on top of the aircraft. If you plan on mounting the assembly inverted under the aircraft, some modifications to the back plate may be required., This kit includes:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for the servo options listed below. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
This is a stand alone pan/tilt FPV module that uses ...ReadyMadeRC
CAMERA CABLE 4-WIRE 6-PIN SUPER COMPACT TO IMMERSIONRC/FATSHARK
The wiring order on the camera connector as delivered will fit the following cameras directly:, RMRC-600XV (Old version), RMRC-700XV,
This is a super small 4-wire 6 pin camera lead ...ReadyMadeRC
CAMERA CABLE (4-WIRE,6PIN FOR OLD VERSION RMRC-700XV)
PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera you need to use a regulator before the cable.,
This is a 4-wire camera lead with a 6 pin ...ReadyMadeRC
CAMERA CABLE (4-WIRE, FOR CAMERAS WITH AUDIO)
Directly compatible with the following cameras:, RMRC-600XV, RMRC-540, RMRC-480, RMRC-420 (not 420xv), PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera you need to use a regulator before the cable.,
This is a 4-wire camera lead compatible with many different ...ReadyMadeRC
CAMERA CABLE (4-WIRE SUPER COMPACT TO IMMERSIONRC/FATSHARK)
The wiring order on the camera connector as delivered will fit the following cameras directly:, RMRC-420, RMRC-480, RMRC-540, RMRC-LL600, NOTE: The above cameras are all 12V cameras, and the IRC transmitters have a 5V output. This cable assumes you are connecting the camera directly to an EZOSD and/or you are using a regulator bypass adapter (available separately) so you are supplying the proper voltage to the camera.,
This is a super small 4-wire camera lead compatible with ...ReadyMadeRC
CAMERA CABLE (3-WIRE)
The wiring order on the camera connector as delivered will fit the following cameras directly:, RMRC-520, RMRC-420XV, RMRC-MINI, RMRC-PICO, DPC-171/KX-171,, It will fit the following cameras by simply rearranging the wiring order (User responsible for verifying compatibility):, SN777 , KX-131, KX-191, Others?, PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera such as the KX131, you need to either use a regulator before the cable.,
This is a 3-wire camera lead compatible with many different ...ReadyMadeRC
CAMERA CABLE (3-WIRE SUPER COMPACT)
The wiring order on the camera connector as delivered will fit the following cameras directly:, RMRC-520, RMRC-420XV, RMRC-MINI, RMRC-PICO, DPC-171/KX-171,, It will fit the following cameras by simply rearranging the wiring order (User responsible for verifying compatibility):, SN777 , KX-131, KX-191, Others?, PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera , you need to either use a regulator before the cable or power the camera with a separate power source.,
This is a super small 3-wire camera lead compatible with ...ReadyMadeRC
CAMERA CABLE (3-WIRE SUPER COMPACT TO IMMERSIONRC/FATSHARK)
The wiring order on the camera connector as delivered will fit the following cameras directly:, RMRC-520, RMRC-420XV, RMRC-MINI, RMRC-PICO, DPC-171/KX-171,, It will fit the following cameras by simply rearranging the wiring order (User responsible for verifying compatibility):, SN777 , KX-131, KX-191, Others?,
This is a super small 3-wire camera lead compatible with ...