ppm Review

R2Hobbies

TURBORIX 8CH PPM DUAL CONVERSION RC FM RECEIVER

PPM Dual Conversion Receiver Model Number : ..." />

Type	PPM / 8Channels
compatibility	with most PPM transmitter (Futaba/Hitec/GWS and etc)
Frequency	35/40/72Mhz
Dimensions	44.5 X 28 X 16mm

Weight:,

Turborix 8 Channel PPM Dual Conversion Receiver Model Number : ...

ReadyMadeRC

COMPUFLY USB TO PPM CONVERTER (JR)

PPM stream that can be used ..." />

RED	PPM
BLACK	Ground
Channel resolution	1024 (10 bit)
Max Channel Count	10 channel
PPM Mode	Positive/Negative PPM selectable
Cable Length	120cm
Software	GNU licensed OpenSource Software for everyone
- go to SysWOW64 folder on command prompt (type "cd c	windowssyswow64")

For people wiring directly without using the trainer plug, the wiring configuration is:, Features:, Control Application with full source code under GNU license:, , Software Download :, CompuFly.zip latest version, Windows XP/Vista/7 USB drivers :, CP210x_VCP_Win_XP_S2K3_Vista_7.zip,

The CompuFly generates a PPM stream that can be used ...

ReadyMadeRC

COMPUFLY USB TO PPM CONVERTER V2 (FUTABA)

PPM stream that can be used ..." />

RED	PPM
BLACK	Ground
Channel resolution v2.0	2048 (11bit)
Channel resolution v1.0	1024 (10bit)
Max Channel Count	10 channel
PPM Mode	Positive/Negative PPM selectable
Cable Length	120cm
Software	GNU licensed OpenSource Software for everyone
- go to SysWOW64 folder on command prompt (type "cd c	windowssyswow64")

For people wiring directly without using the trainer plug, the wiring configuration is:, Features:, Control Application with full source code under GNU license:, , Software Download :, CompuFly.zip version 1.35, Windows XP/Vista/7 USB drivers :, CP210x_VCP_Win_XP_S2K3_Vista_7.zip,

The CompuFly generates a PPM stream that can be used ...

HiModel

36MHZ WFT08 8-CHANNEL PCM/PPM RADIO SYSTEM

MODEL NO.	WFT08
●Band	36 MHz
●Output	≤750mW
●Current drain	≤300mA
●Output pulse	1000μs-2000μs
●Modulation	PPM/PCM
●RF module	individual
●Power	1.2v×8 (9.6v) Ni-cad/Ni-MH rechargeable batteries
RECEIVER type	WFR08-P PPM

, , , , , , Specifications:, , , , , , , , , , , TRANSMITTER, 1.5v×8(12v) normal alkalescence batteries, * Both mode 1 & mode 2 are available, mode 2 will be provided by default for international orders, you can specify the stick mode by leaving a message in the Remark field on the last step when place the order., *This radio come in white foam packing only, no outer color carton., , ,

Features: 8 Channels transmitter Specification and features 1. Model: WFT08 ...

ngHobbies

3DR PIXHAWK AUTOPILOT W/O GPS AND PPM ENCODER

• Weight	38g (1.31oz)
• Width	50mm (1.96")
• Thickness	15.5mm (.613")
• Length	81.5mm (3.21")

Note: Pixhawk is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers (and all those sold by 3D Robotics) allow for PPM output, but some, such as non-S.BUS Futaba receivers, do not., Pixhawk includes:, • Pixhawk autopilot, Microprocessor:, • 32-bit STM32F427 Cortex M4 core with FPU, Sensors:, • ST Micro L3GD20 3-axis 16-bit gyroscope, Interfaces:, • 5x UART (serial ports), one high-power capable, 2x with HW flow control, Power System:, • Ideal diode controller with automatic failover, Weight and Dimensions:,

Pixhawk is an advanced autopilot system designed by the PX4 ...

HiModel

FRSKY 2.4G 8-CHANNEL RECEIVER W/PPM OUTPUT V8R7SP

Model	V8R7-SP
Operating Voltage Range	3.0V-16.0V
Operating Current	30mA
Resolution	3072
Latency	22ms
Specified	7CH, 9g, 49mm×23mm×12mm, 1.5km-2.5km
Warning	DO NOT connect servos to channel 8, otherwise servos will get hot or even burn out.

, , , , , , Specifications:, , , , , , , , , , , V8R7-SP improves the smoothness of high-speed digital servos., Bind Procedure:, 1) Turn on your transmitter and switch it to PPM mode, turn off the TX., 2) Turn on your transmitter while holding the programming button. Release it a few seconds later. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver., 3) Connect the battery to the receiver while holding the receiver’s F/S button. The LED on the receiver will flash, indicating the binding process is complete. Turn off the transmitter and receiver., 4) Turn on your transmitter. Connect the battery to the receiver when ORANGE LED on TX is on. The LED on the receiver will indicate the receiver is receiving commands from the transmitter. In a few seconds system is ready to work (communication is established)., Binding is required only to set up a new link (like new or additional receiver or transmitter module). To control multi-receivers, every receiver should be programmed with the transmitter in binding state., Failsafe:, V8R7-SP supports failsafe function for all channels. Just do it as bellow:, After the receiver has been bind, press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, the failsafe is set up successfully., If you do not need the failsafe function any more, just re-bind the receiver., , ,

Includes/Requires: Includes:1 x V8R7SP receiver